I am studying for an exam this week, and I want to check my steps and answers for this one problem. Air enters a nozzle steadily with a density of 2.21 kg/m^3 and velocity of 40 m/s and leaves at 180 m/s with a density of 0.762 kg/m3. If the nozzle inlet has an area of 90 cm^2, determine: a) The Volumetric flow rate at the in let (m^3/s) b) The Mass flow rate (kg/s) through the nozzle; c) The exit area of the nozzle (cm^2

I am studying for an exam this week, and I want to check my steps and answers for this one problem. Air enters a nozzle steadily with a density of 2.21 kg/m^3 and velocity of 40 m/s and leaves at 180 m/s with a density of 0.762 kg/m3. If the nozzle inlet has an area of 90 cm^2, determine: a) The Volumetric flow rate at the in let (m^3/s) b) The Mass flow rate (kg/s) through the nozzle; c) The exit area of the nozzle (cm^2

Name: I am studying for an exam this week, and I want to check my steps and
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: I am studying for an exam this week, and I want to check my steps and answers for this one problem. Air enters a nozzle steadily with a density of 2.21 kg/m^3 and velocity of 40 m/s and leaves at 180 m/s with a density of 0.762 kg/m3. If the nozzle i

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.33P

See similar textbooks

Similar questions

Air enters a fan through a duct velocity of 6.3 m/s and an inlet static pressure of 2.5cm of water less than the atmospheric pressure. The air leaves the fan through the duct at a velocity of 11.25 m/s and a discharge pressure of 7.62cm of water above the atmospheric pressure. If, the density of the air is 1.2kg/m3and the fan delivers 9.45m3/s, what is the fan efficiency when the power input to the fan is 13.75 kW at the coupling. Show schematic diagram and provide solutions.
At the bottom of a pressurized water tank is a mouth with a diameter of 5 cm, where water is discharged into the atmosphere. The water level is 2 m above the outlet. The tank air pressure above the water level is 300 kPa (absolute) and the atmospheric pressure is 100 KPA. Determine the initial rate of water discharge (volumetric flow rate) from the tank, neglecting the effects of friction.
Water flows through a constricted pipe at a uniform rate. At one point, the diameter of the pipe is 0.056 m and the pressure is 5.7 x 104N/m2. At another point, 0.8 m higher than the previous point, the diameter is 0.023 m and the pressure is 1 X 104N/m2 . Calculate the velocities at the lower section and the upper section. Also calculate the rate of flow. Density of water = 1000 kg/m3.
Between two sections in a vessel, a fluid moves in a steady flow manner. At entrance: A1=20 m2, ρ1=1300 kgm/m3. At exit: A2=10 m2, ʋ2=0.00125 m3/kg, ῡ2=3 m/min. Determine the following: a) ḿ1 in kg/min b) ῡ1 in m/min
14A fluid flows at a speed of 7.5 m/s in a pipe with a diameter of 35 cm. What is the power, in W, of the pump to overcome the irreversible pressure drop when the pressure drop along the pipe is calculated to be 6300 Pa?
In a centrifugal blower (Figure Q1) air enters in to the blower normal to the blades (a1 = 0°), and exits at 40°from the radial direction (∞2=40°). The blower rotates at w = 200 rad/s. The inlet radius r1 = 4 cm, and inlet widthb1 = 6 cm. The outlet radius r2 = 10 cm and outlet width b2 = 3 cm. Assuming 100% etticiency and considering 0.2m3/s flow rate, calculatea) the net head produced by the blowerb) the breaking horsepower in watt.(Take density of air Pair = 1.2 kg/m', gravity, g = 9.81 m/52)
PAY ATTENTION TO THE QUESTION : What is the resulting flow rate in the system if three pumps are used in parallel? (a) 0.483 m^3/s (b) 0.364 m^3/s (c) 0.333 m^3/s (d) 0.563 m^3/s 1. The Head -flowrate curve for a centrifugal pump is given by: HP = 28 -30Q2 Where, HP is in meter and Q is in m3/s . This pump is used to pump water for a system with the following (H-Q) curve: HS = 8 + 150Q2 Where, HS is in meter and Q is in m3/s . IT SAYS : if theee pumps are used in parallel PAY ATTENTION Multiple choice choose correct answer
Please anybody answer this ASAP,i need the answer in 40 min Air flows isentropically through a channel To = 310 ° C. The two ends have identical areas, namely A = 25 cm², pressure p1 = 160 kPa and p2 = 65 kPa Determine a). Mass flow rate, b). Throat area and C). Ma2
A pressurized tank of water has a 10-cm-diameter orifice at the bottom, where water discharges to the atmosphere. The water level is 3 m above the outlet. The tank air pressure above the water level is 300 kPa (absolute) while the atmospheric pressure is 100 kPa. Neglecting frictional effects, determine the initial discharge rate of water from the tank
36 - Water flows at a speed of 0.75 m/s in a 6 cm diameter pipe. What is the mass flow rate of the water passing through the pipe? a) 137.5 kg/min B) 353 kg/min NS) 75.4 kg/min D) 127.17 kg/min TO) 88.4 kg/min
water circulates throughout a house in a hot water heating system. if the water is pumped at a speed of 0.55 m/s through a 6.0-cm diameter pipe in the basement under a pressure of 3.03x105 pa, what will be the velocity and pressure in a 2.6-cm diameter pipe on the second floor 5.0 m above?
11. Water flows through a constricted pipe at a uniform rate. At one point, the diameter of the pipe is 43mm and the pressure is 8.3 x 10 4N/m2. At another point, 1 m higher than the previous point, the diameter is 17 mm and the pressure is 2.7 x 104 N/m2 . Calculate the velocities at the lower section and the upper section. Also calculate the rate of flow. Density of water = 1000 kg/m3.