b) A multi-stage impulse generator has 10 stages with the following circuit elements: storage capacitor of 1µF per stage, a front resistor of 5800 per stage and a tail resistor of 3k per stage. The value of the front capacitor is 9nF. The charging voltage per stage is 50kV (i) Calculate the parameters of the single stage equivalent circuit for the above generator (ii) Calculate the front time (T1) and tail time (T2) for the above generator

b) A multi-stage impulse generator has 10 stages with the following circuit elements: storage capacitor of 1µF per stage, a front resistor of 5800 per stage and a tail resistor of 3k per stage. The value of the front capacitor is 9nF. The charging voltage per stage is 50kV (i) Calculate the parameters of the single stage equivalent circuit for the above generator (ii) Calculate the front time (T1) and tail time (T2) for the above generator

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

design a chopper drive circuit for a maximum motor current of Im=2.2 A with all mathematical calculations. Thw value of sense resistor is 0.1 ohm
A long shunt compound generator with Ra = 0.05 ohms, Rse = 0.3 ohms, and Rsh = 200 ohms delivers a load current of 30 A; VT=220V. Calculate the induced emf, as well as Ia. As a contact drop, allow 1.0 per brush. (Draw the circuit diagram)
Two star connected induction motor are fed by 4160 V, line to line, 3-phase 60 Hzmotor control 20 ft away. Motor A drives a 600 HP compressor. The efficiency of themotor is 90 %, and its power factor is 0.5. Instruments of motor B indicate 1730 kW,277 Amps (a) Determine the capacity in microfarads of a wye connected capacitor bankthat is required to correct the power factor of the load to 0.966. (b) If asynchronous motor is installed in place of motor B and used instead of the capacitorbank to achieve tha same overall power factor (0.966), what must its power factorbe?
A short shunt compound generator with Ra = 0.05 ohms, Rse = 0.3 ohms, and Rsh = 200 ohms delivers a load current of 30 A; VT=220V . Calculate the induced emf, as well as Ia. As a contact drop, allow 1.0 per brush. (Draw the circuit diagram)
Determine the stability of the system whose characteristic equation is 25s^4 + 105s^3 +85s^2+42s + 10 = 0 according to the Routh Stability criterion with the following explanations: a) Create the routh table according to the given characteristic equation. b) Calculate the necessary coefficient in the table you created. c)State whether the system is stable and how you determined it.
DESIGN A CONVENTIONAL POWER SUPPLY USING 220V AC , 10 KILO OHMS RESISTOR ,4 SILICON DIODES, CAPACITOR , TRANSFORMER WITH 20:1 TURNS' RATIO AND PERCENTAGE ERROR= 5 PERCENT. FIND THE SUITABLE REGULATOR
A 3-phase, two-pole, Y-connected, 60 Hz, 10MVA, 13.8kV synchronous generator has a synchronous reactance of 10.5 ohms and negligible resistance. It is operating in parallel with a large power system (infinite bus). The grid operates at 13.8kV and the internal generated voltage of the generator is 20.48 kV. What is the maximum output power the generator can theoretically deliver?
Q#4: A single phase motor operating off a 400V, 50Hz supply is developing 10KW with an efficiency of 84% and a power factor (p.f) of 0.7 lagging. Calculate; i) The input apparent power; ii) The active and reactive components of the current; iii) The reactive power (in kilovars).
A 12-stage impulse voltage generator has a capacitor C. The wave front resistance equal to 0.6kΩ and wave tail resistance 7019Ω. If the wave front and wave tail times of the impulse wave are 2 μs and 0.06 ms respectively. Calculate (i) the capacitance of each capacitor in the generator and (ii) the capacitance of the load capacitor (C2)?
Q#4 A single phase motor operating off a 400V, 50Hz supply is developing 10KW with an efficiency of 84% and a power factor (p.f) of 0.7 lagging. Calculate; The input apparent power; The active and reactive components of the current; 3.The reactive power (in kilovars).
A stepper motor with a 450 step angle provide a resolution of 8 steps per revolution True False
An alternative current (AC) motor draws 13A current from 220V/50Hz power system network during the operation. The power factor of this 2kW motor is calculated as 0,8, In order to increase power factor from 0,8 to 0,9 a shunt capacitor is connected system for compendsation. Calculate the accurate capacity value of the capacitor while modified system has 0,9 power factor.