b) A square cross section is made of wood with 2 m long pin-ended column as shown in Figure 7. Given the data, E = 13 GPa, Gall = 12 MPa, and a factor of safety of 2.5 to calculate Euler's critical load for buckling. Examine the size of the cross section if the column is to safely withstand the following conditions. i) 100 kN load ii) 200 kN load 2 m D Figure 7

b) A square cross section is made of wood with 2 m long pin-ended column as shown in Figure 7. Given the data, E = 13 GPa, Gall = 12 MPa, and a factor of safety of 2.5 to calculate Euler's critical load for buckling. Examine the size of the cross section if the column is to safely withstand the following conditions. i) 100 kN load ii) 200 kN load 2 m D Figure 7

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The figureshows a copper rod that is placed in an aluminum tube. The rod is 0.005 in. longer than the tube of length L = 10.3 in. Find the maximum safe load P (in lb with four decimal places) that can be applied to the bearing plate, using the following data: area of copper = 2.98 sq, in. area of aluminum = 3.17 sq, in. E of copper = 17066931 ksi E of aluminum = 10016839 ksi allowable stress for copper = 19002 ksi allowable stress for aluminum = 10966 ksi
A W section is used as a column of hinged ends with a length of 6 m. Fy = 248 MPa and E = 200GPa.Use the formula for combined stress. Section properties:A = 21300 mm2Sx = 2080 x 10^3 mm^3rx = 119 mmSy = 746 × 10^3 mm^3ry = 68.10 mm Questions:Determine the safe distance along the plane of the web could an eccentric load of 197.6 kN be placed.Hint Answers: 1,420.18
A prestressed hollow box cross section is shown in the figure. The area of prestressed reinforcement in the tension zone is 1148 mm2. Use grade 270 for seven wire-strand tendons. fpy = specified yield strength of tendons fpu = specified tensile strength o pre stressing tendons fse = effective prestress after losses fse = 1022 MPa Aps = 1148 mm2 fpy = 0.95fpu fc’ = 34.5 MPa fpu = 1860 MPa a. Compute the Yp factor. b. Compute the stress in prestressed reinforcement at nominal strength. c. Compute for the design moment capacity. d. Compute the effective pre stressing force after losses of stress e. Compute the depth of the compression block. f. Compute the pre stressing steel ratio.
A foundation must be built on a non-cohesive soil that has the following characteristics: soil density = 18.0 kN/m3, saturated soil density = 19.0 kN/m3, internal friction angle of 30°, depth of planting = 1.5 m and depth of water table = 0.8 mThe gross allowable load with FS = 3 is 700 kN. Determine the dimensions of the proposed footing using Meyerhof theory.
A rail road track is laid at a temperature of 15F with gaps of 0.01 ft between the ends of the rails. The rails are 33 feet long. If they are prevented from buckling, what stress will result from a temperature of 100F? a. 9500 b. 9300 c. 10600 d. 1090
A W section is used as a column of hinged ends with a length of 6 m. Fy = 248 MPa and E = 200GPa.Use the formula for combined stress. Section properties:A = 21300 mm2Sx = 2080 x 10^3 mm^3rx = 119 mmSy = 746 × 10^3 mm^3ry = 68.10 mm Questions:Determine the safe distance along the plane of the web could an eccentric load of 197.6 kN be placed. Kindly Use NSCP 2015 please for this problemHint Answers: 1,420.18
A closely coiled helical spring is made of 10 mm diameter steel wire, the mean diameter of the coil is 68.4 mm and there are 8 coils. Taking the modulus of rigidity as 100 kN/mm2, (a) find the stress in the wire, in N/m2, when carrying an axial load of 807N, (b) the deflection, in mm, and (c) the spring rate in N/mm. Express your answer in 3 decimal places.
The bridge has a length of 16 meters with a continuous linear load value at the beginning and end of the bridge as 0 and 25 N/m, respectively. What is the amount of the resultant load? a)180 N b)200 N c)90 N d)150 N e)400 N
An aluminum [E = 10,000 ksi] control rod with a circular cross section must not stretch more than 0.22 in. when the tension in the rod is 2100 lb. If the diameter of the rod is 0.372 in., determine the maximum length of the rod.
Choose correct answer: A mild steel rod of 15mm diameter that is 1.5.m in length is elongated by 0.15cm along its longitudinal direction by a load of 15 kN. The intensity of stress is 0.08488 N/mm2 48.88 N/mm2 84880 N/mm2 84.88 N/mm2
A simply supported beam, having the following properties: 5.5 m length, Mcr = 30 kN-m, Ig = 7000x10^6 mm^4, Icr = 3000x10^6 mm^4, uniformly distributed dead load = 5 kN/m, uniformly distributed live load = 7 kN/m, Ec = 21,000 MPa. b) Determine the computed value of Ie (DL+LL).
The cross section of the rod in the picture is a circle and the elastic modulus of the material is 200 GPa (material S235JRG2). The rod is pulled with a force of F = 5250 N. Determine the minimum value of the rod diameter d when the rod length is L = 5250 mm and a length change of ΔL = 4.0 mm is allowed for the rod. Also determine the safety with respect to the rod. Use units in calculations [N, mm] Enter the answer to one decimal place. Do not round the invoices in the intermediate stages, but only the final answer!