For a fluid of specific gravity SG = 0.86 flowing past a flat plate with an upstream velocity of U = 5 m/s, the wall shear stress on the flat plate was determined to be as indicated in the table below. Use the momentum integral equation to determine the boundary layer momentum thickness, = 0 (x). Assume 0= 0 at the leading edge, x = 0. Enter the value of 0 (in mm) at x = 2 m.

For a fluid of specific gravity SG = 0.86 flowing past a flat plate with an upstream velocity of U = 5 m/s, the wall shear stress on the flat plate was determined to be as indicated in the table below. Use the momentum integral equation to determine the boundary layer momentum thickness, = 0 (x). Assume 0= 0 at the leading edge, x = 0. Enter the value of 0 (in mm) at x = 2 m.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water flows at a velocity of 1.2 m/s over a flat plate 1.2 m long. Assume 1/7thpower law and determine the boundary layer thickness and displacementthickness. Compare the values with values calculated using laminar flowcorrelations. υ = 1 × 10−6m2/s.
In gliding (unpowered) flight, the lift and drag are in equilibriumwith the weight. Show that if there is no wind, theaircraft sinks at an angletan θ ≈drag/liftFor a sailplane of mass 200 kg, wing area 12 m2, and aspectratio 11, with an NACA 0009 airfoil, estimate (a) the stallspeed, (b) the minimum gliding angle, and (c) the maximumthe distance it can glide in still air when it is 1200 mabove level ground.
The Cessna Citation executive jet weighs 67 kN and has awing area of 32 m2. It cruises at 10 km standard altitudewith a lift coeffi cient of 0.21 and a drag coeffi cient of0.015. Estimate (a) the cruise speed in mi/h and (b) thehorsepower required to maintain cruise velocity.
A Savonius rotor can be approximatedby the two open half-tubes in Fig mounted ona central axis. If the drag of each tube is similar to thatin Table 7.2, derive an approximate formula for therotation rate Ω, as a function of U, D, L, and the fluidproperties (ρ, μ).
Local boundary layer effects, such as shear stress and heattransfer, are best correlated with local variables, rather usingdistance x from the leading edge. The momentum thicknessθ is often used as a length scale. Use the analysis of turbulentflat-plate flow to write local wall shear stress τw in terms ofdimensionless θ and compare with the formula recommendedby Schlichting: Cf ≈ 0.033 Reθ -0.268.
Air at 20°C and 1 atm flow at 20 m/s past the flat platein Fig. . A pitot stagnation tube, placed 2 mm fromthe wall, develops a manometer head h = 16 mm of Meriamred oil, SG = 0.827. Use this information to estimatethe downstream position x of the pitot tube. Assumelaminar flow.
The drag of an airfoil (Fig.) increases considerably ifyou turn the sharp edge around 180° to face the stream. Canyou explain this?
Consider a commercial airliner flying at a speed of 540 mph (relative to the air) at analtitude of 30,000 feet. (c) With a mean molar mass of M = 28.9 g/mol, determine the Reynolds number andMach number in flight. Justify your choice of characteristic length by referencinga commercial aircraft currently in service.(d) Is this flow inviscid or viscous? Is this flow subsonic or supersonic? Qualitativelydescribe the differences between these flight regimes.
A liquid (? = 850 kg/?3; ? = 1.7 × 10−1 Pa ∙ s) flows tangentially past a flat plate. If the free stream velocity is 2 m/s Question 1: what is the velocity 5 m downstream from the leading edge of the plateand 15 mm away from the plate. Question 2: if that plate is 10 m long and 3 m wide. Determine the drag force on the plate when liquid flows over both sides of the plate. (just only answer Question 2)!!!
1.A.)A semi-cylindrical concrete structure having a radius of 5 m and length of 3 m is rested on ground. Wind (air having a density ρ=1,2 kg/m3 ) at a free-sream speed of 3 m/s with an atmospheric pressure of 100 kPa far upstream the structure blows over the structure. The air entrance to the structure is at ground level corresponding to the forward stagnation point . Determine the magnitude of pressure at ground level in terms of gage .Assume flow potential ANSWER: 5,4 Pa 1.B.)A semi-cylindrical concrete structure having a radius of 5 m and length of 3 m is rested on ground. Wind (air having a density ρ=1,2 kg/m3 ) at a free-sream speed of 3 m/s with an atmospheric pressure of 100 kPa far upstream the structure blows over the structure. The air entrance to the structure is at ground level corresponding to the forward stagnation point . Since the magnitude of minimum pressure is acting on the top of the structure determine the magnitude of lift force due to the pressure difference in…
Air at 20 °C flows at V = 10 m/s over a flat plate of length L= 1.52 m and width W = 2 m.Calculate the boundary layer thickness at the trailing edge of plate and drag force on one sideof plate if:a. Surface of plate is smooth.b. Surface of plate is rough.The air properties at 20 °C are: Density, ? = 1.2 kg/m3and dynamic viscosity, ? = 1.8x 10-5kg/m·s and kinematic viscosity, ν = 1.516×10-5m2/s. kindly give me the solution of this problem with correct and logical reasoning.
Air at 20 °C flows at V = 10 m/s over a flat plate of length L= 1.52 m and width W = 2 m.Calculate the boundary layer thickness at the trailing edge of plate and drag force on one sideof plate if:a. Surface of plate is smooth.b. Surface of plate is rough.The air properties at 20 °C are: Density, ? = 1.2 kg/m3and dynamic viscosity, ? = 1.8x 10-5kg/m·s and kinematic viscosity, ν = 1.516×10-5m2/s. I got the first solution which was wrong kindly solve it correctly