(b) Estimate the total uphill resistance force (F) for a truck with an estimated rolling resistance force of 13272.93N, on the same asphalt road but inclined at Mg = 17% grade with respect to the horizontal axis. What braking force (Fbrake) is required to prevent the truck from any downhill acceleration?

(b) Estimate the total uphill resistance force (F) for a truck with an estimated rolling resistance force of 13272.93N, on the same asphalt road but inclined at Mg = 17% grade with respect to the horizontal axis. What braking force (Fbrake) is required to prevent the truck from any downhill acceleration?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A freshwater boat of mass 400 kg is supported by a rectangularhydrofoil of aspect ratio 8, 2 percent camber, and12 percent thickness. If the boat travels at 7 m/s and α = 2.5°,estimate (a) the chord length, (b) the power required ifCD∞ = 0.01, and (c) the top speed if the boat is refitted withan engine that delivers 20 hp to the water.
Example 1.10 gave an analysis that predicted that theviscous moment on a rotating disk M = πμ V R 4 /(2 h ). Ifthe uncertainty of each of the four variables ( μ , Ω,, R , h )is 1.0 percent, what is the estimated overall uncertaintyof the moment M ?( a ) 4.0 percent ( b ) 4.4 percent ( c ) 5.0 percent( d ) 6.0 percent ( e ) 7.0 percent
Aerodynamics NACA 747A415, chord is 180 cm 1) What is the location of favorable pressure gradient of the upper surface, measured from LE? 2) What is the location favorable pressure gradient of the upper surface, measured from TE?
Suppose you are designing the propeller of a radio-controlled model airplane. The overall diameter of the propeller is 34.0 cm, and the hub assembly diameter is 5.5 cm. The propeller rotates at 1700 rpm, and the airfoil chosen for the propeller cross section achieves its maximum efficiency at an angle of attack of 14°. When the airplane flies at 30 mi/h (13.4 m/s), calculate the blade pitch angle from the root to the tip of the blade such that ? = 14° everywhere along the propeller blade.
A model of the Airbus 320 is tested in a wind tunnel using air at standard conditions. If the tunnel airspeed is 50m/s, calculate the water speed if the same model is to be tested in a water tunnel atdynamically similar conditions. Take mair=1.73 x 10-5Pa.s, mwater=10-3Pa.s, rair=1.225kg/m3 andrwater=1000 kg/m3.
You are given a drone with an average chord length of 8 in., a wingspan of 2.5 ft, and a weight of 300 g. Based on figure 2, would it stay in the air at a speed of 5 m/s? (Assume ρ=1.225 kg/m3 and Nu=1.516*10-5 m^2/s)
A windmill turns a series of slender rods fixed about one end . They are initially 2 meters long, and go at a speed of 15 revolutions per minute. I suggested making the blades 1m long to reduce the cross-sectional area of the windmill, keeping the mass the same for mechanical stress consistency. How fast are the windmill blades going now, in revolutions per minute?
A car (m = 2000kg; Cd = 0.3; Ac = 2.5m ^ 2) travels on a flat track at a speed of 100 km / h. Air: 1.2 kg / m ^ 3; u = 1.8 x 10 ^ -5 Pa.s. a) Calculate the power required to overcome the drag. How much power does a 27 km / h head wind blow? b) What is the power required to climb a ramp, with a 5º slope, at 100 km / h? Consider the absence of wind and neglect rolling friction. Tip: Start by calculating the force the engine has to exert.
A tractor-trailer truck is coasting freely, with no brakes,down an 8° slope at 1000-m standard altitude. Rollingresistance is 120 N for every m/s of speed. Its frontalarea is 9 m2, and the weight is 65 kN. Estimate the terminalcoasting velocity, in mi/h, for (a) no deflector and(b) a deflector installed.
3.) Automotive engineers work very hard to improve the value of the drag coefficient for cars. Suppose you have a car with a mass of 3000. kg and an effective surface area of 4.00 m^2. The engine can generate a maximum force of 28,000. N. Let the coefficient of kinetic friction be 0.200, and the coefficient of static friction be 0.400. Air has a density of 1.21 kg/m^3. (back on earth) (3a) Draw a free-body diagram for your car, including both drag and friction, when the car is moving at its maximum velocity. (3b) If the maximum value of your car's velocity is 150.0 m/s, then what is the drag coefficient for the car? (3c) Suppose your engineers change the drag coefficient to 0.300 - what would be your maximum velocity then with the same force from your engine.
A ship 200 f t long with a wetted area of 5000 ft2 moves at 25 ft/s. Find the friction drag, assuming that the ship surface may be modeled as a flat plate, and ρ = 1.94 slugs/ft3 and ν = 1.2 × 10−5 ft2/s. What is the minimum power required to move the ship at this speed?
Assume that the Flettner rotor ship of Fig. has a waterresistance coefficient of 0.005. How fast will the shipsail in seawater at 20°C in a 20-ft/s wind if the keel alignsitself with the resultant force on the rotors? [Hint: This is aproblem in relative velocities.]