B- in figure below the plat has a width of 1 m. the heater is connected to the heater has length of 50mm what is the maximum heater power required?. Air T-25°C = 60 m/s con T_= 25°C = 60 m/s -Plate 1 Plate 1 7₁-230°C Plate 5 -T₁ = 230°C www -150 mm -- Quixx = 50 mm L=250 mm 2- Typical heater Insulation IL₁

B- in figure below the plat has a width of 1 m. the heater is connected to the heater has length of 50mm what is the maximum heater power required?. Air T-25°C = 60 m/s con T_= 25°C = 60 m/s -Plate 1 Plate 1 7₁-230°C Plate 5 -T₁ = 230°C www -150 mm -- Quixx = 50 mm L=250 mm 2- Typical heater Insulation IL₁

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A CSP supercritical steam power plant using a concentrating collector arrayfor DSG (refer to Figure 8.12) is operating under the following conditions:• Plant electric power output Pel = 28 MW• Intensity of beam solar radiation incident on the concentrator apertureIbc = 798 W/m2• Aperture area of a single concentrator module Aap = 420 m2• Efficiency of the collector ηc = 0.7• Power plant thermal efficiency ηth = 0.39• Efficiency of the electric generator ηg = 0.97• HTF is water/steam• Superheated steam condition at the absorber outlet/turbine inlet:ps = 250 bars, ts = 600°C• Feedwater temperature at the absorber inlet = tw = 280°C Calculate (i) the power plant overall (electrical) efficiency, (ii) the thermal capacity of the power plant, (iii) the rate of useful heat output of aDSG collector module, (iv) the number of concentrator modules, and (v) the steam generation rate of the solar collector.
The food storage room requires a cooling system with a capacity of 10 tons of refrigeration that operates at an evaporator temperature of -17.8 ° C and a condenser temperature of 30.1 ° C. The refrigerant used is R-717 and the system operates in saturated conditions.a. COPb. Refrigerant flow ratec. Heat loss rate in the condenser
NOTE: Only answer the highlighted parts, because a-c has already been answered, only answer letters G H and I. ThanksAn Ammonia refrigerant vapor compression system is utilized as an air-cooled water chiller. It is operating at a condenser temperature of 40oC and an evaporator temperature of 0oC. The system develops 15 Tons of Refrigeration. Determine:g. LMTD and AMTD in the condenserh. The water flow rate of the chiller if it enters the evaporator at 10oC and leaves at 5oC.i. LMTD and AMTD in the evaporator
The food storage room requires a cooling system with a capacity of 10 tons of refrigeration that operates at an evaporator temperature of -17.8 celsius and a condenser temperature of 30.1 celsius. The refrigerant used is R-717 and the system operates at saturated conditions. specify:a. COP =b. Refractory flow rate =c. heat loss rate in the condenser =
The food storage room requires a cooling system with a capacity of 10 tons of refrigeration which operates at an evacuation temperature of -17. 8 degrees Celsius and the condenser temperature is 28.0 ° C. The refrigerant used is R-717 and the system operates at saturated conditions. Determine: Cop, refrigerant flow rate and heat loss rate in the condenser.
The food storage room requires a cooling system with a capacity of 10 tons of refrigeration that operates at an evaporator temperature of -9.2 ° C and a condenser temperature of 30.9 ° C. The refrigerant used is R-134a and the system operates in saturated conditions. a. COP = b. Refrigerant flow rate = ... kg/s c. Heat loss rate in the condenser = .... kJ/s
The food storage room requires a cooling system with a capacity of 10 tons of refrigeration that operates at an evaporator temperature of -9.2 ° C and a condenser temperature of 28.6 ° C. The refrigerant used is R-134a and the system operates in saturated conditions. a. COP =b. Refrigerant flow rate = kg / s. c. Heat loss rate in the condenser = kJ / s.
The food storage room requires a cooling system with a capacity of 10 tons of refrigeration which operates at an evaporator temperature of -9.2 ° C and a condenser temperature of 35.1 ° C. The refrigerant used is R-134a and the system operates at saturated conditions. specify: a. COP = b. Refrigerant flow rate = kg / s c. Heat loss rate in the condenser = kJ / s
The food storage room requires a cooling system with a capacity of 10 tons of refrigeration that operates at an evaporator temperature of -17.8 ° C and a condenser temperature of 30.1 ° C. The refrigerant used is R-717 and the system operates in saturated conditions. a. COP b. Refrigerant flow rate c. Heat loss rate in condenses
The food storage room requires a cooling system with a capacity of 10 tons of refrigeration that operates at an evaporator temperature of -17.8 ° C and a condenser temperature of 32.1 ° C. The refrigerant used is R-717 and the system operates in saturated conditions. a. COP =b. Refrigerant flow rate = ... kg / s.c. Heat loss rate in the condenser = ... kJ / s.
A heating plant for a large medical campus requires 5506 MBH (1MBH \= 1,000,000 btuh) of heating capacity. Which of the following pipe size and velocity in feet per second (fps) for the main would be needed if the plant is a 62 psig medium-pressure steam system? (Hint: Table 7.2) a.8" pipe at 130 fps b.4" pipe at 150 fps c.2" pipe at 100 fps d.4" pipe at 130 fps e.5506 MBH; 62 psig
The food storage room requires a cooling system with a capacity of 10 tons of refrigeration that operates at an evaporator temperature of -17.8 ° C and a condenser temperature of 30.1 ° C. The refrigerant used is R-717 and the system operates in saturated conditions. a. COP = ... b. Refrigerant flow rate = ... kg / s c. Heat loss rate in the condenser = ... kJ/s