(b)Solve the base pitch, centre distance, whole depth and contact ratio of a gear withthe given parameters: Pa= 6, 20 degree pressure angle, 18-tooth pinion is meshedwith a 74-tooth gear.Solve the contact ratio of a gear when the base pitch, P, is the same length of action,Z in Question Q2(b).(c)(d)If this gear (Q2(b)) is a one of the component needed for designing a compoundgear train with ratio at 250:1, design the gear.

Answered: Image /qna-images/answer/8d952604-b593-4520-a497-51a6ad791596.jpg

Answered: (b) Solve the base pitch, centre…

(b) Solve the base pitch, centre distance, whole depth and contact ratio of a gear with the given parameters: Pa= 6, 20 degree pressure angle, 18-tooth pinion is meshed with a 74-tooth gear.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For a pair of standard gears, the module is m=2.5mm，pressure angle is α=20 0. ha*=1. c*=0.25. The teeth number on gear 1 is z1=22. The standard center distance is a=68.75mm. Find the following parameters of gear 2: the teeth number, z2 = ( ) the diameter of reference circle, d2=( )mm the diameter of addendum circle da2 =( )mm the diameter of dedendum circle df2 =( )mm
A spur pinion of pitch diameter 50 mm rotates at 200 rad/s and transmits 3 kW power. The pressure angle of the tooth of the pinion is 20°. find the total force exerted by a tooth of the pinion on other gear?
There are two pairs of closed soft tooth surface spur gears A and B Parameters of A: modulus m = 2mm, number of teeth Z, = 40,Z, = 90, width of teeth b =60mm. %3D Parameters of B: modulus m = 4mm, number of teeth Z, = 20,Z, = 45, width of teeth b = 60mm. %3D The accuracy of the two pairs of gears is grade 8, and other conditions are the same. Try to compare the contact fatigue strength and bending fatigue strength of the two pairs of gears? And explain the reason?
8.7 A pair of involute gears with 16° pressure angle and 6 mm module is in mesh. The number of teeth on pinion is 16 and its rotational speed is 240 r.p.m. When the gear ratio is just 1.75, find, in order that the interference is just avoided, (a) the addenda on pinion and gear wheel (b) the length of path of contact, and (d) the maximum velocity of sliding of teeth on either side of the pitch point. (DAV Indore, 1989) (Ans. a, 9.6 mm; a 4.2 mm; 35.41 mm; V = 95.58 cm/s) %3D
There are two pairs of closed soft tooth surface spur gears A and B,Parameters of A: modulus m = 2mm, number of teeth Z1 = 40, Z2 = 90 , width of teeth b = 60mm.Parameters of B : modulus m = 4mm, number of teeth Z1 = 20, Z2 = 45 , width of teeth b = 60mm.The accuracy of the two pairs of gears is grade8, and other conditions are the same. Try to compare the contact fatigue strength and bending fatigue strength of the two pairs of gears? And explain the reason.
A spur pinion of pitch diameter 50 mm rotates at 200 rad/s and transmits 3 kW power. The pressure angle of the tooth of the pinion is 20°, what is the total force exerted by a tooth of the pinion on the tooth on a mating gear?
The figure below shows the power transmitted through a gear drive to multiple output shafts. Gear A is mounted on an electric motor with a rotational speed of 600rpm. Gear A drives a simple gear train consisting in gears B, C, D, and E and transfers the input power to each gear to the shaft on which is mounted. The power delivered from shafts B, C, D, and E are: 8hp, 12hp, 5hp, and 5hp, respectively. For simplicity, all gears have a diametral pitch of 3 and the following numbers of teeth: NA=75, NB=15, NC=120, ND=15, NE=36. The torque on shaft D is most likely: 2015 lb in 105 lb in 250 lb in 630 lb in
The figure below shows the power transmitted through a gear drive to multiple output shafts. Gear A is mounted on an electric motor with a rotational speed of 600rpm. Gear A drives a simple gear train consisting in gears B, C, D, and E and transfers the input power to each gear to the shaft on which is mounted. The power delivered from shafts B, C, D, and E are: 8hp, 12hp, 5hp, and 5hp, respectively. For simplicity, all gears have a diametral pitch of 3 and the following numbers of teeth: NA=75, NB=15, NC=120, ND=15, NE=36. The expected rotational speed on shaft E is most likely: 375 rpm 600 rpm 1250 rpm 3000 rpm
Q.8 A pair of helical gears in which teeth on pinion are 20 and on gear are 30, the normal module is 5 mm and normal pressure angle is 20°. The helix angle is 30°. The pinion is provided 5 kW at 720 rpm. Determine various forces on the teeth.
A pair of helical gears transmit 15 KW power and the pinion is rotating at 1000 rpm. The helix angle is 0.50 radians and the normal pressure angle is 0.35 radians. The pitch diameter of the pinion is 70 mm and the pitch diameter of the gear is 210 mm. Determine the tangential, radial, and axial forces between the gear teeth.
Provide the complete step-by-step solution, given data, conversion of units, and sketch for this problem. A turbine at 30,000 rpm is used to drive a reduction gear delivering 3 hp at 3,000rpm. The gears are 20 degrees involute herringbone gears of 28 pitch and 2 1/8 ineffective width. The pinion has 20 teeth with a helix angle of 23 deg. Determine theload normal to the tooth surface. A. 20.4 lbs B. 24.4 lbs C. 28.4 lbs D. 32.4
As seen in the figure, a construction machine is rotated by a drive mechanism consisting of belt-pulley and spur gear mechanisms. Engine power P = 5.5 kW ; engine shaft speednm = 1500 rpm ; drive pulley diameter Dt = 16 cm ; diameter of the opposite pulley Dk = 55 cm ; number of pinion teeth z1 = 21 ; number of teeth of the counter gearz2 = 60 ; pulley mechanism efficiency ηk = 0.95 ; Since the efficiency of the gear mechanism is ηd = 0.97: a) Find the output shaft speed nç and the torque Mç on this shaft.b) The force on the taut arm of the belt S1 = 450 N;coefficient of friction μ = 0.3 ; If the winding angle α = 160⁰, is the frictionally transmitted moment Ms sufficient to compensate for the Mg moment on the input shaft? Calculate.