Answer D , E and F 1. The figure shows a pair of shaft-mounted spur gears having a diametrical pitch of 6teeth/in with a 14 tooth pinion (gear 2) driving a 49 tooth gear at a pressure angle of20°. The power input is 3/4 hp at 2400 rpm cw. A, B, C, and D are bearings.3.3 in 3 inDetermine the following:a. The Free Body Diagram for both gears.b. The pitch diameters of gears 2 and 3.c. The transmitted load.d. The torque Tin on the pinion shaft.e. The radial and tangential forces on gear 3f. The output torque of gear 3 shaft.

Answered: Image /qna-images/answer/9deee34a-320c-4c62-9589-93c1823b7b43.jpg

.. The figure shows a pair of shaft-mounted spur gears having a diametrical pito teeth/in with a 14 tooth pinion (gear 2) driving a 49 tooth gear at a pressure 20°. The power input is 3/4 hp at 2400 rpm cw. A, B, C, and D are bearings. D 3 in 3 in ermine the following: 1. The Free Body Diagram for both gears. . The pitch diameters of gears 2 and 3. . The transmitted load. 1. The torque Tin on the pinion shaft. . The radial and tangential forces on gear 3

.. The figure shows a pair of shaft-mounted spur gears having a diametrical pito teeth/in with a 14 tooth pinion (gear 2) driving a 49 tooth gear at a pressure 20°. The power input is 3/4 hp at 2400 rpm cw. A, B, C, and D are bearings. D 3 in 3 in ermine the following: 1. The Free Body Diagram for both gears. . The pitch diameters of gears 2 and 3. . The transmitted load. 1. The torque Tin on the pinion shaft. . The radial and tangential forces on gear 3

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Provide the complete step-by-step solution, given data, conversion of units, and sketch for this problem. A turbine at 30,000 rpm is used to drive a reduction gear delivering 3 hp at 3,000rpm. The gears are 20 degrees involute herringbone gears of 28 pitch and 2 1/8 ineffective width. The pinion has 20 teeth with a helix angle of 23 deg. Determine theload normal to the tooth surface. A. 20.4 lbs B. 24.4 lbs C. 28.4 lbs D. 32.4
The figure shows a double-reduction helical gearset. Pinion 2 is the driver, and it receives a torque of 1200 Ibf • in from its shaft in the direction shown. Pinion 2 has a normal diametral pitch of 8 teeth/in, 14 teeth, and a normal pressure angle of 20° and is cut right-handed with a helix angle of 30°. The mating gear 3 on shaft b has 36 teeth. Gear 4, which is the driver for the second pair of gears in the train, has a normal diametral pitch of 3 teeth/in, 15 teeth, and a normal pressure angle of 20° and is cut left-handed with a helix angle of 15°. Mating gear S has 45 teeth. Find the magnitude and direction of the force exerted by the bearings C and D on shaft b if bearing C can take only a radial load while bearing D is mounted to take both radial and thrust loads.
For a pair of standard gears, the module is m=2.5mm，pressure angle is α=20 0. ha*=1. c*=0.25. The teeth number on gear 1 is z1=22. The standard center distance is a=68.75mm. If the actual center distance is a’=69.75mm, find the working pressure angle α’=( )°
1. A pair of 20 degree full depth spur gears have module of 2.5 and to be mounted on shafts with center distance of 90mm and gear ratio of 3. Determine: a. If there is interference b. If the center distance was increased by 3mm, find the backlash produced c. length of action and contact ratio
Two straight-toothed bevel gears mesh with a shaft angle of 90° and a diametral pitch of 5. The pinion has 20 teeth, and the gear ratio is 2:1. The addendum and dedendum are the same as for 20 stub teeth. For the gear, determine the pitch radius, cone angle, outside diameter, cone distance, and face width.
A set of gears is used to reduce the speed from an electric motor to a shaft driving a grocery checkout conveyor, depicted below. The gear on the motor shaft is a 10-pitch pinion, has 18 teeth, and drives at 1200 rpm clockwise. The driven gear has 72 teeth. The motor has failed and is to be replaced with the only motor available, a 600 rpm motor with an 8-pitch pinion. Specify the set of commercially available 20⁰ spur gears, by number of teeth (N3and N4), that would result in the same conveyor speed and can be used without modification to the mounting (the center distance must not change). Find the number of teeth N3 on the pinion (drive) gear (teeth): Find the number of teeth N4 on the driven gear (teeth):
For a pair of spur gears, one design decision is to specify the pressure angles. Please select the common values of pressure angle per textbook. 300 200 250
Shaft a in the figure has a power input of 75 kW at a speed of 1000 rev/min in the counterclockwise direction. The gears have a module of 5 mm and a 20° pressure angle. Gear 3 is an idler (b) Find the torque T4c that gear 4 exerts on shaft c.
The figure below shows the power transmitted through a gear drive to multiple output shafts. Gear A is mounted on an electric motor with a rotational speed of 600rpm. Gear A drives a simple gear train consisting in gears B, C, D, and E and transfers the input power to each gear to the shaft on which is mounted. The power delivered from shafts B, C, D, and E are: 8hp, 12hp, 5hp, and 5hp, respectively. For simplicity, all gears have a diametral pitch of 3 and the following numbers of teeth: NA=75, NB=15, NC=120, ND=15, NE=36. The torque on shaft D is most likely: 2015 lb in 105 lb in 250 lb in 630 lb in
The figure below shows the power transmitted through a gear drive to multiple output shafts. Gear A is mounted on an electric motor with a rotational speed of 600rpm. Gear A drives a simple gear train consisting in gears B, C, D, and E and transfers the input power to each gear to the shaft on which is mounted. The power delivered from shafts B, C, D, and E are: 8hp, 12hp, 5hp, and 5hp, respectively. For simplicity, all gears have a diametral pitch of 3 and the following numbers of teeth: NA=75, NB=15, NC=120, ND=15, NE=36. The expected rotational speed on shaft E is most likely: 375 rpm 600 rpm 1250 rpm 3000 rpm
In a gear set, a 36-tooth spur pinion drives a 60-tooth spur gear. The teeth of these gear are cast iron profile. The diametral pitch is 6-teeth/in, the face width si 0.5 inches, and the pressure angle is 20 degrees. Assume that the pinion transmits 10 hp at a speed of 2000 rpm. Find the tangential load in lbf Find the contact stress in kpsi, assuming CP=1960 psi.
A gear train is composed of four helical gears with the three shaft axes in a single plane, as shown in the figure. The gears have a normal pressure angle of 20 and a 30 helix angle. Gear is the driver, and is rotating counterclockwise as viewed from the top. Shaft b is an idler and the transmitted load from gear 2 to gear 3 is 500 Ibf. The gears on shaft b both have a normal diametral pitch of 7 teeth/in and have 54 and 14 teeth, respectively. Find the forces exerted by gears 3 and 4 on shaft b