b)State two (2) material used for rolling contact bearing.c)A shaft is supported as shown in Figure Q2(c). The weight of the pulley is 1000N andtensions in the belt in the horizontal direction are 3000N and 1500N respectively. Life ofbearing shoutd be 50000 hours at 900 rpm. Determine:i)the resultant radial force of bearing at A and B, andii)the proper size of straight cylindrical bearing to be used at supports.3000 NAB1500 N200 mm300 mmFigure Q2(c)

Two material use for rolling contact bearing ****As per our company policy we are supposed to only…

Answered: b) State two (2) material used for…

Engineering

Mechanical Engineering

b) State two (2) material used for rolling contact bearing.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The energy required to shear a 1-in. round bar is approximately 1000 ft-lb. In use, the shearing machine is expected to make a maximum of 40 cutting strokes a minute. The frictional losses should not exceed 18 % of the motor output. The shaft carrying the flywheel is to average 150 rpm. (a) What motor horsepower is required? (b) Assuming a size of flywheel and choosing appropriate f C, find the mass and sectional dimensions of the rim of a cast-iron flywheel. The width of the rim is to equal the depth and is not to exceed 3 ½ in. It would be safe to assume that all the work of shearing is supplied by the kinetic energy given up by the flywheel.
When a circular rod of diameter 10 cm and length 10 m is subjected to torque of 10 kN-m. Then angle of twist is _____ degree if modulus of rigidity is 100 GPa.
The system is made up of a bar, supported by a pin at point A and by a smooth collar at point B (the collar slides on the ABG bar). The collar is pinned to bar BDE, and bar BDE is supported by a pin at D and a cable at end E. Draw the bar BDR horizontaly and generate the cutting force diagram, flexing moment,show the max values of cutting force and flexing moment and its position . With T=26lb, a=4 in, b=9 in
An input shaft of a gearbox with motor power P = 7 kW and rotation number n = 1300 rpm. The diameter of an input shaft is d = 20 mm and its material is 16MnCr5. A force of F = 2800 N forces the shaft due to the operation of a gear wheel connected with a wedge on the input shaft. The distances of the gear from the bearings are given as L₁ = 40 mm and L2 = 60 mm. In the most dangerous section, you are required to check the strength according to the S = 3 safety factor. If the section is unsafe in terms of strength, what changes would you make in the design to make it safe? (The surface of the spindle is machined as fine chips, reliability poor Kg = 1.).
2.) An automobile lift raises a car weighing 3000 lbf, 6 ft off the shop floor (Fig. 2-12). Assuming the lift itself weighs 500 lbf and th at friction is negligible , what is the worknecessary to raise the car in ft-Ibf and m-N ?
A shaft was initially subjected to bending moment and then was subjected to torsion. If the magnitude of bending moment is twice of torque, then the ratio of maximum bending stress to shear stress would be
An aluminum bar of circular cross-section and the profile specified in Prob. C2.1 is subjected to a 15-N · m torque. Use numerical integration to compute the angle of twist of the bar. For aluminum, use G = 30 GPa. Please explain how to do it. Thank you
Write legibly, provide manual step by step solution, and diagram for below given problem. A 50cm diameter solid shaft is desired to replace a hollow shaft havng 75cm outside diamter. Consider the strength to be the same, determine the inside diameter of the hollow shaft. Ans. 68.69cm
In the design in the figure, a force of Fn=1912 N in the vertical plane and a torque of Md=916 Ncm in the clockwise direction of rotation act on a machine element with a diameter of D=200 mm on the shaft resting on the A and B bearings. If the angle of the force with the horizontal is b=49o, how many Newtons is the resultant radial force to be considered in the bearing calculation of the bearing A? 1-) The diameter of the machine element on which the force acts will not be taken into account in the calculation of the bearing forces (ie, it will be assumed that the Fn force acts on the axis of the shaft). 2-) Pi number will be taken as 3.14.
2-Falcon company Nizwa is conducting a campus interview to you. You are asked to design the propeller shaft with the following specification. (i) power tranmission = 230 kW(ii) speed = 80 rpm,(iii) Maximum shear stress = 60 MPa(iv) diameter ratio = 1.74(v) The maximum value of the twisting moment is 40% greater than its mean. (i) The mean torque is (Unit is in Nm)=__________ (ii) The maximum torque is (Unit is in Nm)=__________ (iii) The outer diameter of the shaft (unit in mm)=_______________ (iv) The inner diameter of the shaft (unit in mm)=_______________
An aluminum bar of circular cross-section and the profile specified in Prob. C2.1 is subjected to a 15-N · m torque. Use numerical integration to compute the angle of twist of the bar. For aluminum, use G = 30 GPa. Using Simpson`s rule. Please explain thank you
(10) A 40mm diameter shaft is driven @ 3,600rpm by a 150kW motor. The shaft drives a 400mm diameter chain sprocket having an output efficiency of 85%. Determine (a) the torque of the shaft in kN-m (b) output force on the sprocket in kN; (c) power delivered by the sprocket in kW; (d) if the given diameter is safe to use for the said application if: - allowable torsional deflection of 1° based on 20 times its diameter; - maximum allowable stress is 70MPa; - modulus of rigidity is 85x103MPa