(B) The 1400 kg coal car with load is being pulled by the weight E as shown in the figure. If the mass of E is 100 kg, determine the corresponding reactions at wheel supports A and B. The wheels are rolling without sliding (i.e. there is no friction force at the wheels). Pulley at D is smooth. 1400 kg 0.4 m I m 0.6 m

(B) The 1400 kg coal car with load is being pulled by the weight E as shown in the figure. If the mass of E is 100 kg, determine the corresponding reactions at wheel supports A and B. The wheels are rolling without sliding (i.e. there is no friction force at the wheels). Pulley at D is smooth. 1400 kg 0.4 m I m 0.6 m

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.90P: The 14-kN weight is suspended from a small pulley that is free to roll on the cable. The length of...

See similar textbooks

Similar questions

Repeat Prob. 4.152 assuming that the 400-kN force is applied at O instead of L.
The spring attached to the homogenous bar of weight W is undeformed when =0. Determine the smallest spring stiffness k for which the =0 equilibrium position will be stable. Use W = 10 lb, a = 24 in., and b = 6 in. Assume that the spring remains horizontal, which is a valid approximation if is small.
The homogeneous plate of weight W is supported by a ball-and-socket joint at D and three wires. Draw the FBD of the plate and count the unknowns.
The 14-kN weight is suspended from a small pulley that is free to roll on the cable. The length of the cable ABC is 20 m. Determine the horizontal force P that would hold the pulley in equilibrium in the position x=5m.
Draw the FBD for the bar described in Prob. 5.1 if the bar is homogeneous of mass 50 kg. Count the unknowns.
Solve Prob. 10.54 assuming that A and B are connected by a spring of stiffness k = 0.3 W/b and free length b.
Determine the force in the cable OC and the elongation of the spring OA, OB necessary to support a box of mass (M) 400 kg as shown in the figure below. If a = 4 m, b = 5 m, c = 3 m, k1= 5000 N/mm and k2= 4000 N/mm. All calculation using equilibrium of particles equation and must be in Newton (N) and with FBD
the cylinder with a mass of 1000 Kg is supported as shown in the figure, determine the reaction at the hinge.
The boom AC in the figure rests in a ball and socket joint at A and is held in equilibrium by the cables BE and CD. The load applied at C. Determine the coordinates of D in the YZ plane so that the force in CD will be a minimum. Neglect the weight of the boom and cables. Answers: y = 16ft ; z = -34.7ft ( Please i need the solution)
The jib crane is fixed at (A) and carry a box of ( 2500 kg ) mass, as shown in the figure. Determine the reactions on the jib crane at point ( A ). 60 5 m 7 m
PROBLEM 1: The 1500-kg beam ABC has fixed support at A and connected to beam BD by hinge at B. Beam BD has a mass of 2000 kg and supported by a cable at D. The cable is attached to the 20-cm-diameter pulley at E and pulled vertically at the other end, by tension T. Given: a = 1.5 m; b = 0.9 m; c = 1.8 m d = 0.6 m; e = 1.4 m; θ = 75°. Calculate the required tension to maintain in equilibrium. (ANSWER: 12.830KN) Calculate the moment reaction at A. (ANSWER: 28.499) Calculate the total reaction at A. (ANSWER: 22.192) Calculate the vertical reaction at E. (ANSWER: 25.223)
A35-kg disk rests on an inclined surface for which µs = 0.2. The disk is connected to a beamby pin connection at A and the link is supported by pin at B. The vertical load P is applied onthe link AB at a location as shown in Figure 3 (b) Determine the support reactions at pin A and B