Two cylinders having 75 kg and 20 kg mass are connected with a cable and held in equilibrium on smooth surfaces as shown in the figure. Determine the contact forces between the cylinders and the surfaces, the tension in the cable and the angle 0.

Two cylinders having 75 kg and 20 kg mass are connected with a cable and held in equilibrium on smooth surfaces as shown in the figure. Determine the contact forces between the cylinders and the surfaces, the tension in the cable and the angle 0.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.35P: Find the smallest value of P for which the crate in the Prob. 4.34 will be in equilibrium in the...

See similar textbooks

Related questions

Q: The front view of a Zenith CH 750 Cruzer airplane named "Mapanikwa" is shown in the figure below.…

A: The solution of above question can be easily obtained by the use of 3 static equations as given…

Q: 4.15 The 180-kg uniform boom ABC, supported by a horizontal cable at B and a pin at A, carries a…

A: As per the free body diagram given: Take the equilibrium of moment about point A: Consider all the…

Q: gate AB 4 ft long and 2 ft wide is held in position shown due to the spring whose constant is 96.0…

A: Given:length og gate, l=4 ftwidth of gate, w=2 ftk=96.0 lbf/inx=1.5 ft

Q: Activity 1: Determine the angle 0 for equilibrium of the lever shown in the figure. Disregard the…

Q: 30 cm- Go 20 cm E 8 cm 30 cm- 25 cm- e P6.55 and P6.56 HE The elevation and tilt angle of table AB…

Q: The system in the figure is in equilibrium. A concrete block of mass 243 kg hangs from the end of…

A: (a) Tension in wire, T = 1686.73 N. (b) Horizontal reaction at hinge, Rx = 1466.6 N→. (c) Vertical…

Q: Q1/ In the equilibrium position shown in figure below, the uniform bar (AB) has a mass of (50 kg)…

Q: has a mass of 75 kg. 6-90 The plate shown in Fig. The brackets at supports A and B exert only force…

A: Write the position vector of the points A, B, C and D.

Q: . Determine the angle 0 of the 12-ft bar in the figure given where its position is in equilibrium…

A: Let RA and RB are the reactions at the point A and B respectively. And 'α' be the angle marked as…

Q: The horizontal cylinders in the figure shown are piled in a rectangular ditch. Radius of cylinders…

Q: Activity 2. In the figure, the coefficients of friction are as follows: 0.25 between blocks, 0.20 at…

Q: In the figure below, the boom AC is supported in a ball and socket joint at C and by the cables AD…

Q: The mechanism shown in the figure, supports a 50 lb cylinder. Determine the angle ? for equilibrium…

A: Given data as per question Weight =50 lb Spring constant = 200 lb/ft FBD of system

Q: A block of mass 40 kg is resting on an inclined surface as shown in figure 4. A) Draw the free body…

A: Given:- M=40kg Angle = 25 degree To find:- a) Free body diagram of block b) Conditions for static…

Q: A) A mass of 15.0 kg 10 pc suspended by wires in two sides as shown in the figure. Find the tension…

A: Given : Mass = 15kg Acceleration due to gravity g = 10 m/s2 its weight = ( m * g) = 15*10=150 N we…

Q: The figure models the action of the upper body. Forces W, and W2 represent the weight of the head…

A: Consider the diagram as shown below for the given system.

Q: In the figure below, a diver who weighs 65kg stands at one end of a diving board preparing for a…

A: Given Data: Mass of diver, md=65 kg Mass of board, mb=20 kg

Q: The two steel shafts in Fig. have the same diameter and weigh 100 lb each. Neglecting friction at…

A: Consider the diagram shown below for the given system,

Q: Consider the force P applied at point A on the plate of the figure shown (image 1). Assuming that…

A: Given data: Force P=332N Both the options as mentioned above are similar, however the correct…

Q: The uniform bar with end rollers weighs 65 Ib and is supported by the horizontal and vertical…

Q: A fixed crane, as given in figure, has a mass of 1000 kg and is used to lift a 2400-kg crate. It is…

A: Given data: The mass of crane, m1=1000 kg. The mass of crate, m2=2400 kg. Draw the free-body…

Q: A truck shown in Figure: Q 1(a) is at rest on an inclined road, forming an angle of a with the…

Q: Determine the coordinates of D in the YZ plane so that the force in CD will be a minimum.

Q: The weight of the luggage and the suitcase combined is (W) N, as shown in the figure (2). Determine…

Q: A steel ball is resting in a trough as shown in the figure. The weight of the ball is 1100 N.…

Q: PROBLEM 2 For the figure shown, determine the following if the mass of the person is 50kg and the…

A: Dear student, as per the guidelines of Bartleby we are authorized to answer the first question only.…

Q: 8. The uniform rod in the figure shown weighs 400N and has its center of gravity at G. Determine the…

A: To determine the value of tension in the rope and the normal reactions.

Q: 5.0 Ib 30 plg В 30 plg 30 15.0 Ib 20 plg 30 lb ' 20.0 lb-ft 5.0 Ib 20 plg 15 plg 15 plg

A: Force A force is a vector quantity which means it has magnitude and direction. If the magnitude and…

Q: 8. The uniform rod in the figure shown weighs 400N and has its center of gravity at G. Determine the…

Q: The diagram shows the open bonnet of a car d iJyuall. The bonnet is held open at an angle of 60° to…

A: Given data: Weight of bonnet, W = 25 N. Part (1) Draw a free-body diagram of the bonnet. Here, W…

Q: a). A fixed crane has a mass of 1000 kg and is used to lift a 2400 kg crate. It is 5. held in place…

A: Given:- Mass of crane (m) = 1000 kg Mass of crate (M) = 2400 kg To Find:- Draw free body diagram…

Q: 1. (a) The gusset plate in Figure la is subjected to the forces of four members; F is 10 kN and the…

Q: D 50 kN 25 kN

A: This is a simple truss problem. In this question we calculate the reactions at the supports by…

Q: find the value of R1

A: Given: weight of the Carriage (W1) =480 lb Weight of the ladder (W2) =240 lb P= 180 lb Distance…

Q: A loading car, as given in figure, is at rest on a track forming an angle of 25 with the vertical.…

Q: sosceles triangular gate AB, as shown in the figure, is hinged at A. The horizontal force (P s…

Q: A system of levers and bars connected by pins is used as a toggle in a press, as shown in the…

Q: The steel cable is hoisting a 2,000N weight. Assume the weight is not accelerating and the cable is…

A: A pin support will exert both horizontal and vertical components of reaction. The support B is pin…

Q: A 150 kg box is supported by a beam Z and cable K as shown in the figure below. Determine the forces…

A: Given data: Mass of the box, m = 150 kg. Draw the free-body diagram of the system, Apply Lami's…

Q: 20 kg 75 kg 30° 60° Two cylinders having 75 kg and 20 kg mass are connected with a cable and held in…

A: Solution:

Q: 1. The system in the figure is in equilibrium. A mass of 225 kg hangs from the end of the uniform…

Q: Q1/ In the equilibrium position shown in figure below, the uniform bar (AB) has a mass of (50 kg)…

A: given data:- mass of rod = 50 kg find the tension in the cable and reaction at B.

Q: Select the distance a between 2 m and 5 m and the force P between 15 kN and 35 kN in the cage system…

Q: A fixed crane, as given in figure, has a mass of 1000 kg and is used to lift a 2400-kg crate. It is…

A: Mechanical Equilibrium: A body is said to be in Mechanical Equilibrium if it satisfies the…

Q: The uniform rod AB has a mass of 140-kg and it is supported as shown in the figure. If the applied…

A: given data: mass of rod=140kg weight of rod(W)=mg=140*9.81=1.37KN force(F)=1.4KN reaction at A=??

Q: 9. The boom AC in the figure rests in a ball and socket joint at A and is held in equilibrium by the…

A: An object is considered to be in a condition of equilibrium when all of the forces acting on it are…

Q: ABC is a rigid bar, with a pin at B, and cable ADC wound around the pulley at D. There is a force of…

Q: Two smooth spheres of weight W and radius r each are in equilibrium in a horizontal channel of A and…

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

20 kg
75 kg
609
30°
Two cylinders having 75 kg and 20 kg mass are connected with a
cable and held in equilibrium on smooth surfaces as shown in the
figure. Determine the contact forces between the cylinders and the
surfaces, the tension in the cable and the angle 0.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The 14-kN weight is suspended from a small pulley that is free to roll on the cable. The length of the cable ABC is 20 m. Determine the horizontal force P that would hold the pulley in equilibrium in the position x=5m.
The homogeneous plate of weight W is suspended from two cables. Determine the force P that is necessary to keep the plate in the position shown.
Find the smallest value of P for which the crate in the Prob. 4.34 will be in equilibrium in the position shown. (Hint: A rope can only support a tensile force.)
The weight of the uniform bar AB is W. The stiffness of the ideal spring attached to B is k, and the spring is unstretched when =80. If W=kL, the bar has three equilibrium positions in the range 0, only one of which is stable. Determine the angle at the stable equilibrium position.
The homogeneous plate of weight W is supported by a ball-and-socket joint at D and three wires. Draw the FBD of the plate and count the unknowns.
The 40-kg homogeneous disk is resting on an inclined friction surface. (a) Compute the magnitude of the horizontal force P. (b) Could the disk be in equilibrium if the inclined surface were frictionless?
The bar ABC is supported by three identical, ideal springs. Note that the springs are always vertical because the collars to which they are attached are free to slide on the horizontal rail. Find the angle at equilibrium if W = kL. Neglect the weight of the bar.
The center of gravity of the nonhomogeneous bar AB is located at G. Find the angle at which the bar will be in equilibrium if it is free to slide on the frictionless cylindrical surface.
The stiffness of the ideal spring that is compressed by the slider C is k = 250 N/m. The spring is unstretched when =20. When the mass m is suspended from A, the system is in equilibrium at =60. Determine the value of m and whether the equilibrium position is stable or unstable.
Draw the FBDs for the entire structure and the member BDE. Count the total number of unknowns and the total number of independent equilibrium equations. Note that the cable that supports the 1200-lb weight runs over a smooth peg at D.
The spring attached to the homogenous bar of weight W is undeformed when =0. Determine the smallest spring stiffness k for which the =0 equilibrium position will be stable. Use W = 10 lb, a = 24 in., and b = 6 in. Assume that the spring remains horizontal, which is a valid approximation if is small.
The two uniform cylinders, each of weight W, are resting against inclined surfaces. Neglecting friction, draw the free-body diagrams for each cylinder and for the two cylinders together. Count the total number of unknowns and the total number of independent equilibrium equations.