6. An ideal gas with Cv = 1.62 kJ/kg-K and R = 273J/kg-K expands from 0.15m3(cubic meter) and 27 deg. C to 0.35 m3 (cubic meter) during an isobaric processwith p = 150kPa. Consider the process reversible nonflow, determine: b) the change in internal energy in kJ208308178

Answered: Image /qna-images/answer/c7638038-89d5-4f40-ac3b-2247801eefcf.jpg

Answered: b) the change in internal energy in kJ…

Engineering

Mechanical Engineering

b) the change in internal energy in kJ O 208 О 308 O 178

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Kinetically how many degrees of freedom are required to model the system shown in Figure (7)? Also,…

Q: QUESTION 16 Five forces: Fi, Fa. Fa, Fa and Fs are applied to point O. The F= 40N force F2 which…

Q: 4. The 5-kg cylinder is suspended from two equal-length cords. The end of each cord is attached to a…

Q: What horsepower is required to isothermally compress 800 ft3of air per minute from 14.7 psia to 120…

Q: a. With the aid of diagrams describe how a production plan is generated for a traditional 'push'…

Q: Determine the reactions at the supports. 900 N/m 600 N/m 3 m1- 3 am

Q: The figure (not drawn to scale) shows a metallic cylindrical column submitted to a combined load:…

Q: 12 mm PROBLEM 1.9 Two horizontal 22 kN forces are applied to pin B of the assembly shown. Knowing…

A: Given: Two horizontal forces of 22 KN acting on upper joint of the link. The free body diagram will…

Q: Q1/ Find the resultant (R) and the direction (N) of the two forces shown in Figure below ? The angle…

Q: S. The cost of producing a small transistor radio set consists of P 230.00 for labor and P 370.00…

A: The number of sets must be produced per month to break-even is 7143 sets.

Q: A rectangular piece of wood, 55 mm by 101 mm in cross-section is used as a compression block. The…

A: (a) The maximum axial load is 86.42 kN. (b) The allowable compressive stress is 13.74 MPa.

Q: Question: A circular furnace has 2 end diffuse, gray surfaces. Both surfaces (surfaces |1 &2) are…

A: Given:

Q: In some circumstances when two parallel springs, with constants k, and k,, support a single mass,…

A: Given data Mass attached = 20 lbStiffness of one spring is 5 times the stiffness of the otherHence,…

Q: The figure (not drawn to scale) shows a metallic cylindrical column submitted to a combined load:…

Q: The interior of a refrigerator has a surface area of 6.2 m2. It is insulated by a 2 cm thick…

A: find the power required to run the compressor.

Q: Using calculus, find moment of inertia of a right triangle of Show how you would find the vertical…

Q: A hollow connecting rod has an inner diameter of 26.25 mm and is subjected to an axial tensile load…

Q: The gage on an orifice meter resds 42 lb per sq in. What is the velocity of water if the inside pipe…

Q: A mass weighing 20 Ib. stretches one spring 5 times as much as it stretches a second spring. The…

A: Given data Mass attached = 20 lbOne spring stretches 5 times as much as the second spring.The total…

Q: Determine the force in each member of the 300 N truss in Fig. Q1, and state if the members are in…

Q: Please calculate the contact stress and contact force based on the below diagram and information.…

Q: A steel band 8mm thick is to be pulled on to a cylinder 30cm in diameter. The internal diameter of…

Q: A particle travels along a path where y = 8x3. The particle increases height with y = 27t3 where t…

Q: Figure Q3a shows a simply supported beam AB with support reactions RA and RB. Two point loads F1= 35…

Q: Fig. Q1 2. The truss in Fig. Q6 supports the vertical load of 600N. If L = 2m determine the force in…

Q: Determine the pressure difference between pipe A and B for arrangement shown in Fig. P. 1.13.20. 0.2…

Q: 4. At 3:01P.M, a thermometer reading is 90°C is taken outside where the air temperature is -10°C. At…

A: Write the expression of temperature variation. T-TsT0-Ts=e-kt At 3:01 PM, Ts=-10 and T0=90. Then,…

Q: Q A thick-walled cylinder has an inside diameter of 150mm. The inside of the cylinder is subjected…

A: Soln:- d1 = 150 mm r1= 75 mm P1= 350 bar = 350 × 10^5 pa Max.…

Q: Auto-ignition might occurs in spark ignition .4 engine at low engine speed because the flame…

A: Auto ignition is the self-ignition of the fuel or air-fuel mixture before the spark has fired.…

Q: Each cylinder in a four-cylinder car engine has a bore diameter of 63.53 mm and the stroke for each…

A: Consider a cylinder having bore D and swept length L. Then, swept volume or cubic capacity of the…

Q: Problem (5). The internal and external diameters of the centrifugal pump are 200 mm and 400 mm…

Q: A jet of water with a diameter of 52 mm (d) hits a set of vanes, the absolute velocities are as…

A: Given that, Angle made by the absolute velocity at the inlet, α=25° The angle made by the jet at…

Q: 2. The satellite traveling on a acceleration of the airplane in terms of b, e, e, A dish below…

Q: y (0,1) y = cos(x) (T/2, 0)

A: find the centroid of the shaded area.

Q: At the commencement of the compression stroke, the cylinder of an oil engine is charged with air at…

Q: etermine the reactions RA and Rg of the beam loaded as shown in the figure. 600 lb 200 lb 5'- 4' A…

Q: a) Figure Q2a shows a hollow tube of rectangular cross-section subjected to an axial compressive…

Q: Consider an 80 MW coal-fired steam power plant that runs on a reheat Rankine cycle. Steam enters the…

A: given; power(P)=80MWspecific gravity(SG)=1.05volume flow rate(Q)=?

Q: Measurements of pressure at the base and top of a mountain are 74cm and 60cm of mercury…

A: We know that measurement of pressure at the base and top of a mountain are 74 cm and 60 cm of…

Q: How can you know what kind of bars are made. Explain by investigating net magnetization. (Magnetism…

A: Given question: How can you know what kind of bars are made. Explain by investigating net…

Q: b) For the truss structure in Figure Q4, determine the forces FAE, FAB and FCF acting in members AE,…

Q: Figure Q3a shows a simply supported beam AB with support reactions Ra and RB. Two point loads F1 =…

A: First calculate the reactions at support and draw the bending moment diagram

Q: A thin cylindrical rod of uniform mass m and length L is suspended from the ends by two massless…

A: Given : To find : Find the motion's equation

Q: Problem 1. Determine angles a, b, and c shown in the Figure 1. The vertical lines are, of course,…

A: As per our guidelines we are supposed to solve only one question of multiple questions are asked.…

Q: Determine the centroid coordinates (X , ỹ) for the beam section shown in Figure Q6. a) Give your…

A: ( x , y ) = ( 24.375 mm , 41.875 mm )

Q: 3. What are the four major accessories of a Rankine Cycle? Define each

A: Rankine cycle is a cycle including 4 processes with 4 major accessories like Boiler, Turbine ,…

Q: A 90-hp (shaft output) electric car is powered by an electric motor mounted in the engine…

A: find the rate of heat supply to the engine.

Q: Figure Q3a shows a simply supported beam AB with support reactions Ra and Rs. Two point loads F1 35…

A: Using equilibrium conditions as follow 1. Sum of moment about A point zero 2. Sum of vertical forces…

Q: The system is made up of the 1-m, 5.4-kg uniform rod AB and the two uniform disks (each of 0.20 m…

A: Initially the system posses only potential energy. Accordingly, the initial potential energy of the…

Q: True or False Tangential Force is the component of the resultant force lying in the plane of the…

A: True. Tangential force tending to shear one segment of a body to the other.

Question

6. An ideal gas with Cv = 1.62 kJ/kg-K and R = 273J/kg-K expands from 0.15m3
(cubic meter) and 27 deg. C to 0.35 m3 (cubic meter) during an isobaric process
with p = 150kPa. Consider the process reversible nonflow, determine:

b) the change in internal energy in kJ
208
308
178

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

starting with Cp – Cv = show that Cp – Cv = nR for perfect gas. Show that for reversible adiabatic expansion P1V1ϒ = P2V2ϒ
Draw Pv and Ts diagram of reversible isobaric process. Write the relationship between thermodynamic properties.
How to solve this thermodynamics question about mean power?
A curious blacksmith forge 1 kg of iron then dropped it to an insulated container that contains 50 liters of water. Before dropping the iron into the insulated container, the blacksmith measures the temperature of iron and water as 500 °C and 20 °C, respectively. This curious blacksmith is always interested in thermodynamics and tries to calculate equilibrium temperature and the total entropy change because of his/her action. What will be the equilibrium temperature and the total entropy change? Is this process reversible or irreversible? (Density and specific heat of water at 20 °C are 995.10 kg/m3 and 4.16 kJ/kg.C, respectively. Assume that the specific heat capacity of iron is 0.5 kJ/kg.C)
Oxygen at the rate of 3 lb/min undergoes a reversible isobaric process during which its entropy changes -0.35 Btu/lb-°R; V1=17.75 ft3and t1= 400 oF . For both nonflow and steady flow (ΔP = 0 , ΔK = 0 ) processes, compute (a) ΔU and ΔH , (b) W , (c) Q.
A gaseous substance whose properties are unknown, except specified, undergoes an internally reversible process during which v=(-0.1p+300)ft3 where p is in psfa. The pressure changes from 1000 psfa to 100 psfa. The process is a steady flow where the change in kinetic energy is 25 Btu, the change in potential energy is negligible, and ∆? = −300 ???, compute for the heat transferred and work done or by the system in kilojoules.
Steam expands adiabatically in a nozzle from inlet conditions of 130(psia), 420(°F),and a velocity of 230(ft)(s)−1 to a discharge pressure of 35(psia) where its velocity is2000(ft)(s)−1. What is the state of the steam at the nozzle exit, and what is SG for theprocess?
Steam at 1.2 MPa and 500 C undergoes isentropic ( S=C ) expansion process. For mass flow of 2.5 kg/s and final state after expansion is saturation, determine the following: Plot the T-S diagram completely & properly labeled Approximae final pressure of steam Approximate final temperature of steam Work (W) , is it input or output? Heat (Q), is it added or rejected?
p89#9. a certain ideal gas whose R=278.6J/kgm.K and Cp=1.015kJ/kgm.K expands isentropically from 1517 kPa,288 degree celsius to 965kPa. fro 454gmm/s of this gas detrmine,(a)Wnf,(b) V2,(c) change of internal energy and (d) change in enthalpy.
For example, suppose you had 5.0 kg/s of water at 1 MPaa and 500 degrees Celsius that enters an ideal steadystate, steady-flow turbine and, following isentropic expansion, exhausts at 0.025 MPaa: ΔP = 0, and ΔK = 0. The following values are given: a) final temperature; b) quality of steam at turbine exhaust; c) turbine work; and (d) if the turbine's efficiency is 90 percent, calculate the steam quality or temperature of steam at turbine exhaust, as well as the turbine output. (Draw the diagram)
Determine change in specific entropy of the ideal gas from state 1 to state 2 in kJ/kg K
8 kg of water vapor are 2.8 MPa and with 100 degrees celcius SH reject of 2180 Kj/kg of steam at constant Pressure. Determine Enthalpy in (Kj), Internal Energy in (Kj), Entropy in (Kj/K).