b. Describe how the zener stabiliser circuit reacts when: i. there is a fluctuation of the source (input) voltage. ii. there is a fluctuation of the output resistance (load).

Q: What is the function, operation, and application of switching regulator?

A: Due to advancement in power electronics, in today's scenario most of the electrical appliances uses…

Q: Describe why and where choppers are used. With necessary diagrams and equations, explain how an…

A:

Q: 3. What is harmonic restrain and startup characteristic for differential protection and in which…

A: This protection system is employed to protect alternator, transformer and high rating HT motor.…

Q: Using a circuit diagram, describe the operation of linear shunt regulators

A:

Q: Explain the difference between the modulator and demodulator blocks and explain the terms…

A: Up-conversion is a converter it mixer a device that convert to analog signal a low frequency to a…

Q: Explain how to determine the output voltage of the step-down configuration of a switching regulator.…

A:

Q: Describe why and where choppers are used. With necessary diagrams and equations, explain how an…

A: Chopper/DC-DC Converter Chopper/DC-DC Converter is used to change the DC input voltage level to…

Q: Q4 Illustrate in Figure the digital IC signal levels by introducing the concept of noise margin.…

A: Noise Margin The greatest voltage amplitude of an external signal that can be algebraically added to…

Q: A) What are the considerations should be taken at the design of the Thyristor gate trigger signal?…

A:

Q: Discuss the various methods of mounting an accelerometer on a machine and describe the influence of…

A: ANSWER There are three methods of         ACCELEROMETER MOUNTING. 1-…

Q: digital electronics 2 In which option is the logic circuit equivalent of the RTL circuit given in…

A: Given :    Here they have mentioned the the sister transistor logic circuit.     From the given…

Q: What  is  the  typical  hysteresis  at  the  input  of  a  Schmitt  triggered  gate?

A:

Q: voltage gain?

A: Voltage gain is the term which relates ability amplification of the system.

Q: Discuss about Power Thyristor's DC and Ac switching.(with Diagram)

A: Power Thyristor DC circuit is as follows: - This basic "on-off" thyristor terminating circuit…

Q: Using a circuit diagram and output waveform, describe the mechanism of a square wave oscillator.

A:

Q: Explain the operation of the circuit by drawing the AC power control (regulation) circuit with the…

A: AC power control circuit:

Q: Explain and discuss how the clamper circuit with biasing voltage work

A: Brief description : In the above given question they have mentioned a clamper circuit and they want…

Q: Explain the operating principle of power factor correction circuit that can shape the AC input…

A: Power factor correction circuit: In electrical system many loads are connected  some are highly…

Q: Explain the principle of operation of the Mod-14 asynchronous counter with using the required…

A:

Q: What is the operation of a Zener voltage regulator? How it works?

A:

Q: 2.31 If the no-load output voltage of a regulator is 15.5V and the full-load output is 14.9v, what…

A: Sol:-Given data,No load output voltage(VNL)=15.5Vfull load output voltage(VKL)=14.9 Vwe have,

Q: a) When does an E-MOSFET act as an open switch? b) When does an E-MOSFET act as a closed switch? c)…

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: Draw a one-phase bridge type Full Wave Uncontrolled AC/DC converter circuit, explain the working…

A:

Q: .1. The figure represents the Buck Regulator that provides a smoothed Dc current to a practical…

A:

Q: Interface stepper motor with 8086 in emu8086 and control the speed of the stepper motor.

A: Speed of stepper motors are controlled by input pulses   Stepper motors rotate in fixed steps. They…

Q: c) When considering thyristor switching why is Isolated Gate Control needed ?

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: Which IC technology has the lowest power dissipation in general?

A:

Q: What are the applications of a bridge rectifier?

A: The solution can be achieved as follows.

Q: What is series bias clipper and its uses or function?

A: Clipper circuit: Clipper circuit is an electronic circuit that delete a section of an alternating…

Q: For the dc-dc converter (operating in CCM) depicted in the figure below, make all the required…

A: The given DC-DC converter. we have to find the output to the input voltage ratio VoVin=D1-Dwhere…

Q: The OCC is measured by increasing the field current in steps from zero to some maximum value, and…

A: OCC Conditions,i) No loadii) at Rated Speediii)Ea vs If Ea=NPZϕAEa α ϕϕ α IfEa α If If Ea increases…

Q: Explain Transient oscillator Response

A: Transient oscillator Response- The oscillator is an electronic circuit that produces an electronic…

Q: Derivation of three-phase semi-controlled rectifier(Vavg=?) (Vrms=?)

A:

Q: Draw a phase bridge type Full wave uncontrolled AC / DC converter circuit, describe the operating…

A: The full wave uncontrolled AC/DC converter circuit is simply a full wave bridge rectifier. Instead…

Q: c) When considering thyristor switching why is In-line fuse protection needed ? d) Why is it common…

A: The in-line fuse in connected with a thyristor circuit to protect the thyristor  from over-current.…

Q: How the simulation of signal conditioning devices helps in designing them?

A: To find importance of simulation of signal conditioning

Q: Describe the operation of a class C tune power amplifier

A: Here, it is asked to describe the working of the Class C tune power amplifier. So, we will here…

Q: 1) Determine the: a) dc transistor terminal voltages b) hie c) Rin

A: Note : According to the guidelines of the company if the question is having sub parts then we need…

Q: Write about computer simulation of ASSESSING THE TRANSIENT STABILITY.

A: Transient Stability- It is defined as the ability of the power system to return to its normal…

Q: (b) What type of feedback has been used in an emitter follower circuit?

A: The feedback which is used is negative current feedback.There is no voltage gain in this current…