B0:5 m 1,5 m A C -5 m 5 m- 5 m Prob. 6–62

Q: For the lightweight truss shown 9 kN 12 kN 9 kN В H G F 30° A 10 m 10 m 10 m 10 m ( all 30°, 60°,…

A: Due to symmetry,  RA+RE=12(9+12+9)=15 kN

Q: Determine the reactions at the beam supports for the given loading.

A: Draw the free body diagram of the problem. Let the equation of the curve is Using this condition…

Q: C8-49 A 500-lb load is supported by a roller on a beam as shown in Fig. Show that the maximum…

A:

Q: The tool is used to shut off gas valves that are difficult to access. If the force F is applied to…

A: Given data:F = {-60i + 20j + 15k} N

Q: Draw the free body diagram of the beam. 30° 0, -20° 0.8 m 0.3 W

A: The free body diagram of the beam is as follows:

Q: If the beam shown is supported by the fixed wall at B and the rod AC. if the rod has a cross…

A: The force which acts perpendicular to the cross-section of a specimen is termed as normal force and…

Q: 15

A:

Q: 04m d=0.15m D

A:

Q: Determine the resultant of the line load acting on the beam ABC. 1200 Ib/ft y 1700 Ib/ft C 6 ft -8…

A: find the resultant force of the given distributed load.

Q: 2. The 5 m long beam AB has two types of distributed loads, and one concentrated load as shown. Find…

A: In the above given structures beam and truss, we have to find the reactions RA, RB, RA  and RC. Both…

Q: The shaft is supported by a smooth thrust bearing at A and smooth journal bearing at B. Draw the…

A: Given ,         Free body diagram of the shaft loading diagram                       Consider…

Q: 6 kN/m D 1.5 m- 0.75 m - 3.75 m - Fig. P6.1

A:

Q: 6-73. Determine the absolute maximum live moment in the girder bridge due to the loading shown. The…

A: According to the information we have a girder bridge for the maximum resultant positive occurs under…

Q: Determine the support reactions on the beam. The beam has an internal moment of 50kN-m and is…

A: According to the details provided in the question, we need to calculate reactions

Q: For the lightweight truss shown 9 kN 12 kN 9 kN B D H A 30° 10 m 10 m 10 m 10 m ( all 30°, 60°, 90°…

A: Draw the above truss and show the reaction force by pin and roller support. Here RA signifies…

Q: The beam is supported by a pin at A, a roller at B, and a post having a diameter of 50 mm at C.…

A:

Q: The bent pipe ABCD lies in the ry-plane and bends through 90° at C and supports a hanging weight W…

A: Draw the free body diagram of the bent pipe:

Q: Determine the components of the support reactions at the fixed support A on the cantilevered beam. 6…

A: Given data as per question Vertical applied force =6 KN applying equlibirium equation in y…

Q: Analyze the propped beam loaded as shown below: use either double integration or area moment method.…

A:

Q: Draw the moment diagram for girder IJKL of the building frame. Use the cantilever method of…

A:

Q: A 15 kN/m 6 m- 150 kN - m B -3 m- 50 kN Į C -3 m- D

A:

Q: Determine the reactions at A and B for the beam subjected to the distributed and concentrated loads.…

A:

Q: Cantilever beam has fixed support at the point A as shown in Fig. 4. Determine the component of the…

A: Drawing the free body diagram

Q: Determine the maximum moment (k-ft) at the given structure. Support A is fixed, joint B is a pin and…

A: Given: The structure is shown below:

Q: The bent bar is supported by smooth journal bearings at A, B and C and is subjected to couple moment…

A:

Q: The beam is subjected to the uniform distributed load shown. Draw the shear and moment diagrams for…

A: For the given beam, the point in section AB where shear force changes sign (x2 metres from A) is to…

Q: The weight of the printer is 80 lb with center of gravity at point G. Determine the moment M, of…

A:

Q: The compound beam is pin - supported at C and supported by rollers at A and B. There is a hinge…

A:

Q: Determine the force and moment reactions at A for the beam which is subjected to the load…

A: M=40 kN-m P1=50 kNq1=60 kN/mq2=24 kN/m

Q: 7-63. Draw the shcar and moment diagrams for the beam. 4 kip /n 12 f- 12 ft- Prob. 7-63

A: A pin support will exert both horizontal and vertical components of reaction. A roller support will…

Q: Determine the reaction at A for the beam subjected to the triangular load distribution. 5 kN/m A |B…

A:

Q: Determine the internal resisting forces and moment trans- mitted by section aa in B 30 750 Ib 30 in.…

A: Given: The radius of curvature, R= 30 in force at the end, FP=750 lb at an angle 30o The radius of…

Q: H.W : The 500 kg engine is suspended from the crane boom in the Figure. Determine: 1- The resultant…

A: Draw the free body diagram of the member AB. W=mgW=500 kg9.81 m/s2W=4905 N

Q: Determine the member end moments at b, Mba and Mbc, in the following structure. EI constant 300kN 2m…

A: Given dataP=300kNRoller support at C which exhibit only vertial force

Q: The beam is subjected to the distributed load and the couple shown. If Mis slowly increased starting…

A: Answer: Mo = 5030.67 lb•ft.

Q: Bar ABC has a rectangular cross section of 300 mm by 100 mm. The attached rod DB has a diameter of…

A: Given data as per the question Diameter of DB rod =20 mm Modulus of elasticity of steel =200 Gpa…

Q: The beam is subjected to the distributed load and the couple shown. If Mis slowly increased starting…

A: To determine the value of M for which the contact at B will change from lower surface to upper…

Q: 0.6 m 0.3 m 0.4 m F= 300 N B.

A: Given Data The distance AB in y axis is: 0.2 m The distance AB in x axis is: 0.4 m The force acting…

Q: Determine the reaction moment at the fixed support A in N.m. Given that F= 5 N and L=3 m. Neglect…

A: Force Force is a vector quantity which has direction and magnitude. Force is a change in momentum…

Q: Determine the normal force N inside each bar Sa function of the external force P P 1.5 m B A 2 m…

A:

Q: -1.5 m- -1.5 m |A 1 m M 45° B Determine the support reactions on the member in Fig. The collar at A…

A:

Q: Bar ABC has a rectangular cross section of 300 mm by 100 mm. Attached rod DB has a diameter of 20…

A: Given Cross-section height = 300 mm Cross-section width = 100 mm Diameter = 20 mm To find Slope in A…

Q: The bending moment reaction at the fixed support (in N.M) is 200 N/m A IB -3 m 3 m

A:

Q: 2 m 8 m 3 m 4 m - 6 m

A:

Q: 1. Determine the distance xcto the center of gravity of the homogeneous rod bent into theparabolic…

A:

Q: The shaft is supported by a smooth thrust bearing at A and a smooth journal bearing at B. Take: d1 =…

A:

Q: Analyze the propped beam loaded as shown below: use either double integration or area moment method.…

A:

Q: 4/30 Determine the force in member CM of the loaded truss. 4m+4m+4m+4m4m+4m- E Fl K B N L L. L. A L…

A:

Free Body Diagram

The system of forces acting on a body tends to either rotate it or make the body undergo motion. In general, when an external agent exerts a force on a body, the body undergoes translational motion and rotational motion. The body has six degrees of freedom under the influence of that force. Here, three degrees of freedom are from the translational motion while the other three are from the rotation motion. However, sometimes the bodies are not allowed to undergo any motion and are fixed, under such conditions the body is said to be constrained.