Determine the normal force N inside each bar Sa function of the external force P P 1.5 m B A 2 m Probs. 1-40/41/42

Q: For the lightweight truss shown 9 kN 12 kN 9 kN В H G F 30° A 10 m 10 m 10 m 10 m ( all 30°, 60°,…

A: Due to symmetry,  RA+RE=12(9+12+9)=15 kN

Q: 1200 N/m y 1700 N/m -6 m- -8 m-

A: For UVL :  R1 = WL/2 = 1200 * 6 / 2 = 3600 N X1 = 2L/3 = 2 * 6 /3 = 4 m For trapezoidal load : R2 =…

Q: Determine the location of the single resultant force due to the distributed load measured from A.…

A:

Q: Determine the force in each cable needed to support the 500-lb load.

A: Consider the diagram of the figure with the forces as shown below. Here point C is taken as origin.

Q: P9-3. The post weighs 8 KN/m. Determine the internal normal force in the post as a function of x.…

A: Draw the free body diagram of the given section. 8 X (x) is the weight of the post section and Nx…

Q: Identify the zero force members (if any) in the trus 4 m - 3 m 3 m- P;

A: GIVEN DATA- Given Truss   we have to find zero force member in truss

Q: -1.5 m- 6 kN 2 m 10 kN- F 2'm B

A:

Q: Determine the axial force in member BC of the frame. Note the joint Dis a sliding pin. D. Dimensions…

A:

Q: 35 ft HW05-2 The cable attached to the shear-leg derrick exerts a force on the derrick of F = 350…

A:

Q: For the lightweight truss shown 9 kN 12 kN 9 kN B D H A 30° 10 m 10 m 10 m 10 m ( all 30°, 60°, 90°…

A: Draw the above truss and show the reaction force by pin and roller support. Here RA signifies…

Q: The flywheel is subjected to a torque of M = 75 N ⋅ m. Determine the horizontal compressive force F…

A: The free-body diagram of the problem can be sketched as follows, The flywheel has only one degree…

Q: Determine the extension (m) of the whole system shown if k1 - 14.28 N/m, k2 = 28.89 N/m, k3 =- 37.72…

A: Given:k1=14.28 N/mk2=28.89 N/mk3=37.72 N/mk4=41.16 N/mk5=51.08 N/mF=65.48 N

Q: 1- The crate h force in each s 2- The block smooth plane.

A: given:

Q: 200 - 400 200 N m D 200 F Dimensions in mm Determine the magnitude of the force (in N) of the…

A: As per given question  We have to magnitude Of The force of given fig

Q: The clamp is adjusted so that it exerts a pair of 145-N compressive forces on the boards between its…

A: Taking the lower part of the clamp and drawing the free body drawing for the lower part –

Q: If the tension force in strut AC is 12 kN, determine the forces in struts AB and AD, and the weight…

A: Given data Force in AC = 12 kN Determine the force in other two strut and weight of block.

Q: A man pulls arope attached to abuilding horizontal and vertical components of the force exerted by…

A:

Q: Determine the force in each cable needed to support the 15-kN platform. Set d-0.4 m. 15 kN. 3m 12

A: Given data: F= 15 KN d = 0.4

Q: For the lightweight truss shown 9 kN 12 kN 9 kN C F 30° H G A 10 m 10 m 10 m 10 m ( all 30°, 60°,…

A:

Q: Determine the vertical and horizontal reactions of each support on the fallowing figures. Assurne…

A: Hi, you have submitted multiple questions and it is not specified in which problem you need help.…

Q: The jib crane is supported by a pin at C and rod AB. The rod can withstand a maximum tension of 36…

A: Given data as per the question maximum tension =36 kN Mass of load =2 Mg calculating angle…

Q: Determine the force in each member of the loaded truss. All triangles are 3-4-5. Enter a positive…

A:

Q: Determine the force on each element of the reinforcement and determine if the elements are in…

A:

Q: 2. The 30 cm handle is connected rigidly to the 5cm bar at a right angle. Determine the force…

A: The force applied to the handle is, P=100 N Length of the handle is, L=30 cm

Q: 3-19. Determine the unstretched length of DB to hold the 40-kg crate in the position shown. Take k =…

A:

Q: Refering to the figure below, determine the components of force P along the x-y axes which are…

A:

Q: Neglecting the weights of the members, determine the magnitude of the pin reaction at D when the…

A: According to the given information, the free body diagram of the frame is…

Q: Determine the force components at B and C, as they act upon member AC. 2.25 m 1,200 N BA DYF (DF =…

A:

Q: P1-1. Draw a free-body diagram of the ring at A and identify each force. 200 N

A:

Q: 1-1. Determine the resultant internal normal force acting on the cross section through point A in…

A:

Q: Draw the influence line for the force in member GB of the bridge truss shown.

A: Draw the free body diagram of the truss.

Q: if F-30 kN.0-45 and 45, determine the magnitude and coordinate direction angles of the resultant…

A: Given

Q: Determine the force in each member of the loaded truss. All triangles are isosceles A 30 10 kN 4 m B…

A:

Q: Determine the horizontal and vertical components of force at pins A and D. D 2 m 0.3 m 15m |B -1.5 m…

A:

Q: F3-37. Determine the resultant force and specify where it acts on the beam, measured from A. 9 kN/m…

A: Given : Length of AB is 3m and over-hanged portion is 1.5 m. The following beam is overhanging beam…

Q: A nuclear-reactor vessel has a weight of 500(103) lb.Determine the horizontal compressive force that…

A: Given data: Weight of the reactor, W = 500 x 103 lb. = 500 kip   Drawing the FBD of the reactor:…

Q: The beam is subjected to the distributed load and the couple shown. If Mis slowly increased starting…

A: To determine the value of M for which the contact at B will change from lower surface to upper…

Q: H. 0.5 ft Determine Ax, Ay and Tension at C 0-30 108 lb

A:

Q: 6 ft W A Answer: D -4 ft- B -4 ft- | Determine the normal force at point b using method of section…

A:

Q: Determine the magnitude of the pin force at A Assume W = 900 Ib, a = 5.8 ft, b = 3.9 ft, r = 9 in.

A: Consider the free body diagram for the bar CBA. Also,

Q: Draw the Normal Force DieRm? Draw the sbeac tecse dim Draw the beodior moment diecam? P (kN) q…

A: Given data: The length L1 = 1.8 m. The length L2 = 2.4 m. The length L3 = 1.4 m. The moment M = 6…

Q: The two A-36 steel bars have a thickness of 1 in. and a width of 4 in. They are designed to act as a…

A: let the density of the A-36 steels bars  are  ;ρ=7.85×103 kg/m3 ;   -------From standard valueE=200…

Q: Determine the resultant force at pins A, B, and C on the three-member frame. Given: F = 40N, w = 10,…

A: A pin support will exert both horizontal and vertical components of reaction. The support A is pin…

Q: F 12 ft 3 ft 30 6 ft B -8.4 ft- 2.2 ft 1.4 ft The crane and driver have a weight of 2600 Ibs acting…

A:

Q: Determine the force in member BE of the loaded truss. The force is positive if in tension, negative…

A:

Q: The post weighs 8 kN>m. Determine the internal normal force in the post as a function of x.

A:

Q: The constant moment of 50 N ⋅ m is applied to the crank shaft. Determine the compressive force P…

A: Understand that these a single degree of freedom problem and on independent variable θ can…

Q: H.W6 0.5 ft Determine Ax, Ay and Tension at C 0-30 100 Ib

A:

Q: Q8/ While steadily pushing the machine up on an incline surface, a person exerts 180 N force P as…

A:

Q: Use the method of members to determine the horizontal and vertical forces at the supports A and E…

A: Given: The radius of pulley at B, r = 0.25 m

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.