Beam ABC is subjected to the loading shown, where PB = 75.0 kN. The measurement corresponding to the half-length of the beam is a = 4.50 m. For the cross section shown, b = 75.0 mm, c = 150.0 mm, d = 125.0 mm, and e = 50.0 mm. Point D is located at the centroid of the cross section and point E is located directly above the transition between the web and the top flange. B L H

Beam ABC is subjected to the loading shown, where PB = 75.0 kN. The measurement corresponding to the half-length of the beam is a = 4.50 m. For the cross section shown, b = 75.0 mm, c = 150.0 mm, d = 125.0 mm, and e = 50.0 mm. Point D is located at the centroid of the cross section and point E is located directly above the transition between the web and the top flange. B L H

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter9: Moments And Products Of Inertia Of Areas

Section: Chapter Questions

Problem 9.16P: Figure (a) shows the cross-sectional dimensions for the structural steel section known as C1020...

See similar textbooks

Similar questions

For a beam with the cross-section shown and loaded as shown, find the magnitude of the maximum bending stress in the beam. The moment of inertia about the z axis is 257,633 mm4, the centroid of the section is located 19.67 mm above the bottom surface of the beam, and M = 415 N-m.
A beam is subjected to equal bending moments of Mz = 44 kip·ft. The cross-sectional dimensions are b1 = 6.5 in., d1 = 1.5 in., b2 = 0.90 in., d2 = 6.2 in., b3 = 2.6 in., and d3 = 1.8 in. Determine:(a) the centroid location (measured with respect to the bottom of the cross-section), the moment of inertia about the z axis, and the controlling section modulus about the z axis.(b) the bending stress at point H. Tensile stress is positive, while compressive stress is negative.(c) the bending stress at point K. Tensile stress is positive, while compressive stress is negative.(d) the maximum bending stress produced in the cross section. Tensile stress is positive, while compressive stress is negative.
A beam having a tee-shaped cross section is subjected to equal 18 kN-m bending moments, as shown. Assume bf = 125 mm, tf = 25 mm, d = 185 mm, tw = 20 mm. The cross-sectional dimensions of the beam are also shown. a.Determine the centroid location (measured upward from the bottom), in mm rounded to the nearest tenths. b.Determine the moment of inertia about the z axis. Express your answer in (106) mm4 rounded to three significant figures. c. Determine the controlling section modulus about the z axis. Express your answer in (103) mm3 rounded to three significant figures. d. Determine the controlling section modulus about the z axis. Express your answer in (103) mm3 rounded to three significant figures.
A beam is subjected to equal bending moments of Mz = 57 kip·ft. The cross-sectional dimensions are b1 = 8.3 in., d1 = 1.4 in., b2 = 0.90 in., d2 = 6.2 in., b3 = 2.4 in., and d3 = 1.7 in. Determine: (a) the centroid location (measured with respect to the bottom of the cross-section), the moment of inertia about the z axis, and the controlling section modulus about the z axis. (b) the bending stress at point H. Tensile stress is positive, while compressive stress is negative. (c) the bending stress at point K. Tensile stress is positive, while compressive stress is negative. (d) the maximum bending stress produced in the cross section. Tensile stress is positive, while compressive stress is negative.
Figure (a) shows the cross-sectional dimensions for the structural steel section known as C1020 (channel with a nominal depth of 10 in., weighing 201b/ft). The American Institute of Steel Construction Structural Steel Handbook lists the following properties for the cross section: A=5.88in.2,Ix=78.9in.4, and Iy=2.81in.4. If two of these channels are welded together as shown in Fig. (b), find Ix and Iy for the resulting cross section.
Determine the second moment of area (Iyy) about the centroidal y-axis for a solid homogeneous beam section where the dimensions are b = 125 mm and d = 275 mm. Give your answer in m4 to 2 significant figures.
A cantilever beam is subjected to a concentrated load of 2000N. The cross sectional dimensions of the double-tee beam are shown. Determine (a) the shear stress at point H, which is 17 mm below the centroid of the double-tee shape, (b) the shear stress at point K, which is 5 mm above the centroid of the double tee shape, and (c) the maximum horisontal shear stress in the double tee shape.
A simply supported beam has a symmetrical rectangular cross-section. If the second moment of area (I) of a beam with a rectangular cross-section is 11.50 x 106 mm4 about its centroidal x-axis and the depth dimension (d) of the rectangular section is 180 mm, determine the breadth dimension (b) for this beam section. Give your answer in millimetres (mm) and to 2 decimal places. Assume the beam section material is homogeneous.
A beam is subjected to equal 19.1 kip-ft bending moments. Assume ty = t2 = ty= 1 in., d = 10 in, by= 4 in., and b2 = 7 in. The cross- sectional dimensions of the beam are illustrated. Determine; (a) the distance y to the centroid (measured from the bottom), the moment of inertia & about the z axis, and the controlling section modulus S, about the z axis. (b) the bending stress O, at point H (positive if tension, negative if compression). (c) the bending stress y at point K (positive if tension, negative if compression). (d) the maximum bending stress, Omax produced in the cross section (positive if tension, negative if compression).
1. Determine the maximum positive bending moment in the beam in kN-m. 2. Determine the maximum shear in kN. 3. Determine the location of Neutral Axis, in mm, from the top of the section. 4. Determine the location of the centroid, in mm, from the left of the section. 5. Determine the moment of inertia of the section in x106 mm4 . 6. Determine the moment capacity of the section, kN-m, if fbcap≤300 MPa. 7. Determine the maximum flexural stress experienced by the beam in MPa. 8. Determine the maximum shearing stress in MPa at Neutral Axis. 9. Determine the spacing of rivets in mm. 10. Determine the maximum flexural stress at 1 m from the support at D to E in MPa.
For the beam shown, calculate the magnitude of the bending stress (in psi) at a point 1.14 in from the top of the beam on section 2.72 feet to the right of B if P = 1082 lb, Q = 4244 lb, w = 0.76 in, L = 8.94 in, b = 3.78 in, and h = 0.66 in. Round off the final answer to two decimal places.
For the beam shown, calculate the magnitude of the bending stress (in psi) at a point 0.63 in from the bottom of the beam on a section 1.68 feet to the right of B if P = 2290 lb, Q = 8457 lb, w = 1.37 in, L = 8 in, b = 3.7 in, and h = 1.12 in. Round off the final answer to two decimal places.