Beam ABCDEFG below is subjected to multiple loads as show. The totallength of the beam is 10m. Analyze the beam completely.6 kN10 kN3 kN/m2 kN5 kN-mG3000mm.1000mm 1000mm.2000mm.1000mm.2000mm.3. Determine the shearation for segment B-C. **4. Determine the moment equation of segment C-D.** 5. Determine the maximum negative moment.*6. Determine the maximum positive shear.*7. Determine the maximum positive moment.*8. Determine the moment equation for segment A-B**9. Determine the moment equation at segment F-G.**10. Determine the vertical reaction at F.

Beam ABCDEFG below is subjected to multiple loads as show. The total length of the beam is 10m. Analyze the beam completely. 6 kN 10 kN 3 kN/m 2 kN 5 kN-m 3000mm 1000mm 1000mm. 2000mm 1000mm 2000mm 3. Determine the shear equation for segment B-C. ** 4. Determine the moment equation of segment C-D.**

Beam ABCDEFG below is subjected to multiple loads as show. The total length of the beam is 10m. Analyze the beam completely. 6 kN 10 kN 3 kN/m 2 kN 5 kN-m 3000mm 1000mm 1000mm. 2000mm 1000mm 2000mm 3. Determine the shear equation for segment B-C. 4. Determine the moment equation of segment C-D.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter6: Stresses In Beams (advanced Topics)

Section: Chapter Questions

Problem 6.10.15P: The hollow box beam shown in the figure is subjected to a bending moment M of such magnitude that...

See similar textbooks

Similar questions

A rectangular beam with semicircular notches, as shown in part b of the figure, has dimensions h = 0,88 in. and h1 = 0.80 in. The maximum allowable bending stress in the metal beam is emax = 60 ksi, and the bending moment is M = 600 lb-in. Determine the minimum permissible width bminof the beam.
A rectangular beam with semicircular notches, as shown in part b of the figure, has dimensions h = 120 mm and h1= 100 mm. The maximum allowable bending stress in the plastic beam is emix = 6 M Pa, and the bending moment is M = 150 N · m. Determine the minimum permissible width bminof the beam.
The three beams shown have approximately the same cross-sectional area. Beam 1 is a W 14 X 82 with flange plates; beam 2 consists of a web plate with four angles; and beam 3 is constructed of 2 C shapes with flange plates. Which design has the largest moment capacity? Which has the largest shear capacity? Which is the most economical in bending? Which is the most economical in shear? Assume allowable stress values are: = 18 ksi and ra=11 ksi. The most economical beam is that having the largest capacity-to-weight ratio. Neglect fabrication costs in answering parts (c) and (d) above. Note: Obtain the dimensions and properties of all rolled shapes from tables in Appendix F.
A square tube section has side dimension of 20 in. arid thickness of 0.5 in. If the section is used for a 10-ft-long beam subjected to 1250 kip-in, torque at both ends, calculate the maximum shear stress and the angle of twist between the ends. Use G = 11,600 ksi.
A weight W = 4000 lb falls through a height h = 0.5 in, onto the midpoint of a simple beam of length L = 10 ft (see figure). Assuming that the allowable bending stress in the beam is = 18,000 psi and E = 30 x 10* psi, select the lightest wide-flange beam listed in Table F-l(a) in Appendix F that will be satisfactory.
The hollow box beam shown in the figure is subjected to a bending moment M of such magnitude that the flanges yield but the webs remain linearly elastic. (a) Calculate the magnitude of the moment M if the dimensions of the cross section are A = 15 in., A] = 12.75 in., h = 9 in., and ey =7.5 in. Also, the yield stress is eY = 33 ksi. (b) What percent of the moment M is produced by the elastic core?
A 6 ft long 2” x 12” beam is subjected to a uniform (edge-to-edge) distributed load of 1500 lbs per linear foot. The material has a Young's Modulus E=2,000,000psi. If the allowed bending stress is 2000 psi, the allowed deflection is L/360 and the allowed shear stress is 250 psi: Is the beam safe in bending? Is the beam safe in deflection for L/360, ( deflDIST = (5 w L4)/(384 E I)? Is the beam safe in shear?
Consider the beam shown. Suppose that w1 = 600 N/m , w2 = 300 N/m . Follow the sign convention. A) Determine the internal normal force at point C. NC = ? B) Determine the internal shear force at point C. VC = ? C) Determine the internal moment at point C. MC = ?
What is the minimum steel shear area (Av in sq.mm.) of a beam 300mm wide if fc'=21MPa and fy=340? let the spacing of stirrups be equal to 220mm Pls hand written solution
An I section symmetrical beamhas 200mm wide flange and overall depth of 500mm. Each flange is 25mm thickand the web is 20mm thick. Determine the maximum bending moment that should be imposed in the sectionif the tensile or the compressive stressis not to exceed 40MN/m^2 and what percentage of the moment is resisted by flange or web?
A beam having a tee-shaped cross section is subjected to equal 13 kN-m bending moments, as shown. Assume bf = 95 mm, tf = 25 mm, d = 165 mm, tw = 40 mm. The cross-sectional dimensions of the beam are also shown. Determine(a) the centroid location (measured upward from the bottom), the moment of inertia about the z axis, and the controlling section modulus about the z axis.(b) the bending stress at point H (positive if tensile and negative if compressive).(c) the maximum bending stress (positive if tensile and negative if compressive) produced in the cross section.
A timber dam is made of planking backed by vertical piles. The piles are built-in at the section A where they enter the ground and they are supported by horizontal struts whose center lines are 10 m above A. The piles are spaced 1 m apart between centers and the depth of water against the dam is 10 m. Assuming that the thrust in the strut is two-sevenths the total water pressure resisted by each pile, sketch the form of the bending moment and shearing force diagrams for a pile. Determine the magnitude of the bending moment at A and the position of the section which is free from bending moment. (Cambridge). i. 238 kN-m; 0.75 m from A. ii. 238 kN-m; 0.75 m from B.