Below is a simple circuit built using OPAMP and LDR. LDR, onIt is a passive element whose resistance changes with incident light. In the experiment, the LDR resistance inthe light1kn was found to be 560kN in the dark. Using the circuit to light a lamp in the darkwill be lit and extinguished in the light.5Va. at point V1 for light and dark states toadjust the comparator.Calculate the voltages.33KO10KΩV23302LM741V1LEDLDR

Below is a simple circuit built using OPAMP and LDR. LDR, on It is a passive element whose resistance changes with incident light. In the experiment, the LDR resistance in the light 1kN was found to be 560k£ in the dark. Using the circuit to light a lamp in the dark will be lit and extinguished in the light. 5V a. at point V1 for light and dark states to adjust the comparator. Calculate the voltages. 33KA 10KΩ V2 3300 LM741 v1 LED LDR

Below is a simple circuit built using OPAMP and LDR. LDR, on It is a passive element whose resistance changes with incident light. In the experiment, the LDR resistance in the light 1kN was found to be 560k£ in the dark. Using the circuit to light a lamp in the dark will be lit and extinguished in the light. 5V a. at point V1 for light and dark states to adjust the comparator. Calculate the voltages. 33KA 10KΩ V2 3300 LM741 v1 LED LDR

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Solve for the steady-state values of iR in milliampere (mA), and VC in Volts (V) for the circuit shown below, assuming that the circuit has been connected for a long time.
A solid specimen of dielectric dielectric constant of 4.0, shown in the figure has an internal void of thickness 1mm. The specimen is 1cm thick and is subjected to a voltage of 80 kV(rms). If the void is filled with air and if the breakdown strength of air can be taken as 30 kV(peak)/cm, find the voltage at which an internal discharge
Is the voltage drop of the voltage source equal to the sum of the voltages of the passive elements of an RLC circuit? Or in mathematical terms, Is Vs=VR+VL+VC ? Why? Naturally, by Kirchhoff’s Voltage Law, this equation should be true for an ideal circuit. Knowing that ideal scenarios cannot be replicated perfectly, why could this may not be true?
A resistor, an inductor, and a capacitor are connected in parallel to an ac source with voltage amplitude V and angular frequency v. Let the source voltage be given by v = Vcosvt. (a) Show that each of the instantaneous voltages vR, vL, and vC at any instant is equal to v and that i = iR + iL + iC, where i is the current through the source and iR, iL, and iC are the currents through the resistor, inductor, and capacitor, respectively. (b) What are the phases of iR, iL, and iC with respect to v? Use current phasors to represent i, iR, iL, and iC. In a phasor diagram, show the phases of these four currents with respect to v. (c) Use the phasor diagram of part (b) to show that the current amplitude I for the current i through the source is I = √(I2R) + (IC - IL)2 . (d) Show that the result of part (c) can be written as I = V/Z, with 1/Z = √ (1/R2) + [ωC - (1/ωL)]2.
If the rightmost resistor, 10 ohms, is the load, find the TheveninResistance, Thevenin Voltage and Load Voltage, Vo.Note: In solving forRth, voltage sources are shorted and current sources are opened. Whenlooking for Vth, consider the current and voltage source connected.
A building supplied by a 230 Vrms source has inductive loads that have an average consumption of 40kW and 26kVAR. What is the average current drawn in by the building and its effective impedance?
Vbatt=25 VC1=90 ?CC2=75 ?CC3=60 ?CR1=160 ΩR2=120 Ωt2=21.6 msect3=27 msecConsider the circuit shown below which shows a battery connected to some resistors and capacitors along with some switches which will be toggled opened or closed at different times. The components are listed above. The capacitances are in microFarads (?F), the resitances are in Ohms (Ω), and the times are in milliseconds (msec). A stopwatch is started at time t1=0 ms. At that time, switch S1 is closed and all other switches are open and the capacitor is allowed to charge up.(a). (i)What is the charge (in uC) on C1 at the time the stopwatch reads t2=21.6 ms?a)3690 b)1520 c)5710 d)2630 e)683 f)1750 (a).(ii)What is the current (in mA) through R1 at t2=21.6 ms?34.9 30.4 114 13.6 73.6 52.4 (b)(i)What is the voltage (in V) across R1 at t2=21.6 ms?8.37 5.58 2.18 11.8 18.2 4.85(ii). What is the voltage (in V) across C1 at t2=21.6 ms?63.2 29.1 40.9 7.57 19.4 16.9(c). (i) What is the energy (in mJ) in C1 at t2=21.6 ms?6.63…
Give solution subject: DLD
The currents drawn by the receivers in a given network are given in the figure. Accordingly, active taking into account the current distribution, the point where the greatest voltage drop occurs, and Determine the distribution of the balancing currents in the arms, taking into account their directions.
Compute for IN, RN and the current passing though the 25-ohm resistor using Norton’s Theorem.
Our source ac voltage is 110 Vrms, 50 Hz. Solve for time and the amplitude at a given angle as specified in the table. Show your solutions.
Please answer the following points in detail and rigorously. Instead ofresort to formulas, develop from basic principles (laws ofvoltages and currents, definition of electrical power, properties ofphasors, among others) a) Suppose that between the two terminals of an element there is a voltage v (t) and that through the terminal marked with a positive sign a current i (t). Show that if v (t) and i (t) are sinusoidal and are out of phase an angle θ, then the active power P which is consumed by this element is proportional to cosθ. b) How much is P for a pure inductor and how much for a capacitor pure? Does this make physical sense? c) When the power factor seen between two terminals is specified, Why is it necessary to indicate whether it is late or early? d) Show that the complex power consumed by two elements in parallel is the sum of the individual complex powers. After, repeat the procedure but for two elements in series. e) What meaning would you give to the P consumed by an…