Benzodiazepines test device is a qualitative, preliminary test which would be able to detect whether Benzodiazepines are present in the urine specimen at the cut-off concentration of 300 ng/mL. Is it possible to have a urine specimen which was interpreted as POSITIVE using the Benzodiazepines test device to be interpreted as NEGATIVE by Gas Chromatography/Mass Spectrometry? Justify your answer. A study was conducted by the manufacturer of the benzodiazepines test device to determine whether some compounds would have cross-reactivity at levels of 100µg/mL. List down examples of non cross-reacting compounds

Benzodiazepines test device is a qualitative, preliminary test which would be able to detect whether Benzodiazepines are present in the urine specimen at the cut-off concentration of 300 ng/mL. Is it possible to have a urine specimen which was interpreted as POSITIVE using the Benzodiazepines test device to be interpreted as NEGATIVE by Gas Chromatography/Mass Spectrometry? Justify your answer. A study was conducted by the manufacturer of the benzodiazepines test device to determine whether some compounds would have cross-reactivity at levels of 100µg/mL. List down examples of non cross-reacting compounds

Curren'S Math For Meds: Dosages & Sol

11th Edition

ISBN:9781305143531

Author:CURREN

Publisher:CURREN

Chapter9: Parenteral Medication Labels And Dosage Calculation

Section: Chapter Questions

Problem 1SST

See similar textbooks

Similar questions

Please explain in detail Question #1: A urine and culture should be performed on which type of sample? Question #2: Please explain the consequences of ketone in urine.
Explain this example of the following water quality serial dilution. Note the dilution factors and how you would calculate #’s from the incubated plates. ……A serial dilution yielded TNTC in the 1:1 plate and the 1:10 plate, 50 cfu’s in the 1:100 plate and 3 cfu’s in the 1:1000 plate . What is the concentration (CFU)/ml of the raw sample? Is water acceptable for potable or Recreational use? Explain. When do you use filtration rather than serial dilution
A sample is diluted by a factor of 10 five times. The 10^-3 dilution has 272 colonies on it. Assuming you plated the same volume on each plate, how many colonies would you expect to find on the 10^-2 plate? Include units and use OCD formula.
In sterilization, which among the supplies, instruments, glassware, etc. under the list of materials can be sterilized using either or both equipment below? List them down under the category: a) For “autoclaving” only, B) For Dry heat oven sterilization ,And C) Can be sterilized with either. Materials: 200-ml Erlenmeyer flask Stove 500-ml Erlenmeyer flask Autoclave 10-mL graduated cylinder Analytical balance 100-ml graduated cylinder pH meter Spatula Stirring rod 100-mL beaker Test tubes Distilled water Petri dish Stirring rod Alcohol lamp Glass dropper
Design a serial dilution of a sample to achieve a A) Final dilution of 10-4 using 9.0 mL blanks B) Final dilution of 10-6 using 99 mL blanks C) Final dilution of 10-6 using 9.0 mL blanks
name at least two ways in which the components of a blood sample could interfere with a ethanol in blood lab test if ethanol were not first isolated
A Refractometer was used to test a patient's urine specimen. it has a current specific gravity reading of 1.045. The urine temperature is at 32 degrees Celsius and contains 2 g/dl of Glucose and 1 g/dI of Protein. What is the corrected specific gravity reading? A urine specimen was physically analyzed in the clinical laboratory. The clarity and color of the urine is clear red. Please explain in detail, the possible causes of the clear red appearance of the urine specimen and its simple disease correlation. A Urinometer was used to test a patient's urine specimen, it has a current specific gravity reading of 1.036. The urine temperature is at 29 degrees Celsius and contains 1 g/dl of Glucose. What is the corrected specific gravity reading?
I do not understand the results of this experiment, explain what the results of this experiment are and the purpose Table 2 Absorbance vs CoCl2 concentration Test Tube Number Cobalt Chloride Concentration (mol/mL) Absorbance at 510 nm 1 0.000 0.000 2 0.009 0.024 3 0.018 0.055 4 0.027 0.085 5 6 0.036 0.045 0.112 0.138 7 (Unknown) 0.088
How do you calculate the initial concentration of a sample? How would you make a 1:10 dilution of a broth culture if the final volume of the dilution is 10 ml? How much broth, and how much diluent, would you add? If you made a series of tenfold dilutions, exactly the same way as you described in question 1, what would be the dilution factor in the fifth tube? The following are errors that people commonly make when they perform serial dilutions. Indicate whether you think that the number of cfu/ ml calculated would be too high or too low if you make this mistake. You intend to add 0.9 ml of diluent to each tube and 0.1 ml of culture. Instead, you add 0.5 ml of diluent to each tube and 0.1 ml of culture to the first tube. Then, you make a serial dilution of 0.1 ml into and from each tube as described. You prepare 0.9 ml of diluents in each tube. You add 0.1 ml of culture (from the overnight culture provided) to every tube. You add 0.9 ml of diluent to each tube. You add 0.1 ml of…
In tabular form, provide the principle behind the reaction provided by each pad on a 10-parameter urine reagent test strip. (dipstick)
When a SBIA021 student measured the pH of 1.0M HCI, the student obtained a pH meter and failed to neither check the condition nor the manner of usage of the instrument. The pH meter reading timed out (Did not give a reading) Which of the following problem explanations is most correct? A)The sample in the glass beaker was being swirled vigourously while the electrode was submerged in it for a reading. B)The electrode got submerged much deeper into the solution than it should have. C)All of the above are correct problem explanations O D)The electrode had long direct contact with the environment and the glass membrane got dry.
The presence of a narrow band between the Beta and gamma regions on SPE would most likely indicate which of the following preanalytical errors had occured? sample was mislabeld, sample was grossly hemolyzed, sample was plasma not serum, sample not protected from light