Numerical Analysis (HW. #1) The vertical stress increment (Ao) due to a point load acting on the surface of linearly elastic medium is given as: Ao = 2.7Vr where P is the magnitude of the load, r is the lateral distance, and z is the depth of the point where the stress is to be calculated. If P = 10g kN and r= 1.5 m, determine (by

Numerical Analysis (HW. #1) The vertical stress increment (Ao) due to a point load acting on the surface of linearly elastic medium is given as: Ao = 2.7Vr where P is the magnitude of the load, r is the lateral distance, and z is the depth of the point where the stress is to be calculated. If P = 10g kN and r= 1.5 m, determine (by

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter6: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 6.7P: Use Eq. (6.14) to determine the stress increase () at z = 10 ft below the center of the area...

See similar textbooks

Similar questions

b) An electric pole is held vertically by three equally spaced wires tied at the top of the pole. Each wire is inclined at 45⁰ with a tension of 1 kN, Calculate the vertical stress increase at 1 m depth and the elastic settlement below the axis if E is given as 40 MPa and μ = 0.45. Use Boussinesq’s point load theory
An electric power transmission pole is 12 m above ground level and embedded 2 m into the ground. The butt diameter is 450 mm and the tip diameter (the top of the pole) is 320 mm. The weight of the pole, cross arms, and wires is 33 kN. Assuming the pole transmits the load as a point load, find the change in vertical stress in kPa at 2 m depth.
Find the vertical stress increment at this point of interest using Boussinesq analysis.
Calculate and plot the stress distribution with depth at a point 6.0 m from the corner (along the longest side) of a rectangularly loaded area 18 × 24 m with a uniform pressure of 175 kPa. Perform the calculation using the Boussinesq theoryand the 2:1 method. Comment on the results.When plotting stress distribution with depth, make sure the vertical axis (i.e. depth) increases downwards. Use z=0, 1, 5, 10, 15, 35, 50, and 100 m. Equations that may be helpful are attached.
Figure below shows a 100 kN point load and 40 kN/m line load are applied on the ground surface. Calculate the vertical stress at the depth z=5 m directly underneath of Points A and B.
Q2: For the soil element shown in the figure. Draw Mohr circle, locate OP (origin point), then find the stresses inclined at: 1- 75° from the horizontal plane. 2- With the horizontal plane.
The center of a rectangular area at the ground surface has Cartesian coordinates (0, 0), and one corner has coordinates (7, 18). All dimensions are in meters. The area carries a uniform pressure of 135 kPa. Estimate the stresses at a depth of 15 meters below the ground surface at each of the following locations: (0, 0), (0, 18), (7, 0), (7, 18), and (12, 28).a. Obtain the values by the Boussinesq methodb. Compare the results with those of the 2:1 methodc. Comment on the resultsHint: In the Boussinesq method, the equations attached can be used.
Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine the increase in vertical stress at point A located z = 15 ft below the surface. Given: x = 27 ft.
Using the principles of Mohr’s circles for the soil element shown in Figure 10.36, determine the following:a. Maximum and minimum principal stressesb. Normal and shear stresses on plane AB
Point loads of magnitude 100, 200, and 400 kN act at B, C, and D, respectively (Figure P6.2). Determine the increase in vertical stress at a depth of 6 m below point A. Use Boussinesq’s equation.
Please help me answer this question Refer to Figure 10.47. A exible rectangular area is subjected to a uniformly distributed load of q 5 330 kN/m2. Determine the increase in vertical stress, Dz, at a depth of z 5 6 m under points A, B, and C and more is a photo I sent
Use Eq. (6.14) to determine the stress increase () at z = 10 ft below the center of the area described in Problem 6.5. 6.5 Refer to Figure 6.6, which shows a flexible rectangular area. Given: B1 = 4 ft, B2 = 6 ft, L1, = 8 ft, and L2 = 10 ft. If the area is subjected to a uniform load of 3000 lb/ft2, determine the stress increase at a depth of 10 ft located immediately below point O. Figure 6.6 Stress below any point of a loaded flexible rectangular area