Block A supports a pipe column and rests as shown on wedge B. Knowing that the coefficient of static friction at all surfaces of contact is 0.25 and that θ = 45degrees, determine the smallest force P required to raise block

Q: pin at O and the cable AB. The weight W = 7 N is attached to the free end of the cable. a) Determine…

A: Since you have asked a multi-question, thus we can provide you the solution to the first question…

Q: A small 200-g collar C can slide on a semicircular rod that is made to rotate about the vertical AB…

A: Write the expression of the velocity of the mass.

Q: A 3m uniform plank of weight 203 N rests on two joists as shown. The coefficient of static friction…

A:

Q: Knowing that the coefficient of static friction between the tires and the road is 0.80 for the car…

A: Free body diagram, Considering the four wheels of a car,2Nf+2Nr=mgNf+Nr=mg2........(1)

Q: The 50-lb block A and the 25-lb block B are supported by an incline that is held in the position…

A:

Q: Knowing that the coefficient of static friction is 0.30 between the rope and the horizontal pipe and…

A: (a) Free-body diagram of rope for horizontal and vertical pipes, The contact angle for the…

Q: The cylinder shown is of weight W and radius r. Express in terms W and r the magnitude of the…

A: FBD of the cylinder: For maximum M motion impends both at A and B,

Q: The 50-lb plate ABCD is attached at A and D to collars that can slide on the vertical rod. Knowing…

A:

Q: A homogeneous block of weight W rests upon the incline shown in the figure. If the coefficient of…

A: Given data as per question  coefficient of friction = 0.30 considering…

Q: A block with weight W is pulled up a plane forming an angle a with the horizontal by a force P…

A:

Q: The friction tongs shown in Figure are used to lift a 350 kg casting. Knowing that h = 864 mm,…

A: Given Data:-   M = 350 kg H = 864 mm   Find:-   Smallest allowable friction coefficient M = ?…

Q: The 10-kg block is attached to link AB and rests on a conveyor belt that is moving to the left.…

A:

Q: Block A supports a pipe column and rests as shown on wedge B . Knowing that the coefficient of…

A: As per given  Coefficients of friction =0.25 θ = 45° We have to determine the smallest force P

Q: A wedge A of negligible weight is to be driven between two 100-lb blocks B and C resting on a…

A: Given, (a) The coefficient of the static friction between all surfaces (μ) = 0.35 The weight of the…

Q: In Prob. 8.39, determine the smallest couple MC for which equilibrium will be maintained.(Reference…

A: Given data: The couple about A is MA = 15 N-m The coefficient of friction between rod and collar is…

Q: The double pulley shown is attached to a 10-mm-radius shaft that fits loosely in a fixed bearing.…

A: For given coefficient of static friction rf can be determined as Draw Free body diagram and show…

Q: Question 2: 0.6 m- The uniform 60-kg crate C rests uniformly on a 10-kg dolly D. If the front…

A: The weight of the crate is Wc=mcg=60×9.81=588.6 N The weight of the dolly is WD=mDg=10×9.81=98.1 N…

Q: A 15° wedge is forced under a 50-kg pipe as shown. Knowing that the coefficient of static friction…

A: Given: The wedge angle, θ = 15⁰ The mass of the pipe, m = 50 kg The coefficient of static friction…

Q: A 300-g cylinder C rests on cylinder D as shown. Knowing that the coefficient of static friction l,…

A: Given data-μ=0.35d=75mmD=150mm

Q: A recording tape passes over the 20-mm-radius drive drum B and under the idler drum C . Knowing that…

A: Free body diagram of drum B: Let tension in one of the tapes be T.

Q: Determine the maximum allowable value of weight W at rest. Knowing that the coefficient of static…

A:

Q: Solve Prob. 8.124 assuming that the idler drum C is frozen and cannot rotate.(Reference to Problem…

A:

Q: A 40-kg packing crate must be moved to the left along the floor without tipping. Knowing that the…

A: Given, m = 40 kg μ = 0.35 Also given that, the crate is moved towards to left with tipping which…

Q: The press shown is used to emboss a small seal at E . Knowing that the coefficient of static…

A: Given data Load acting on point C, PC = 250 N. Coefficient of static friction between the vertical…

Q: Q1) Two Crates A and B are connected together with a cable and placed on the inclined plane. If the…

A: Given DataWA=200NWB=150NμA=0.25μB=0.35

Q: Two 10° wedges of negligible weight are used to move and position the 400-lb block. Knowing that the…

A:

Q: A lever AB of negligible weight is loosely fitted onto a 2.5-in.-diameter fixed shaft. Knowing that…

A: Given: The diameter of the shaft, d = 2.5 in The coefficient of friction between shaft and lever, μ…

Q: The main body of the cabinet weighs 15 kg, while the upper rectangular portion weighs 2.5 kg. Assume…

A: The cabinet will not move and will about to tip from point B.

Q: 4. The position of the machine block B is adjusted by moving the wedge A. Knowing that the…

A: A) Raising the Machine: f1 = μN1 = 0.35N1 f2 = μN2 = 0.35N2 Applying the Equilibrium Equations…

Q: A wedge A of negligible weight is to be driven between two 100 lb. block B and C resting on a…

A: Given: The weight of block B and block C is, W=100 lb. The coefficient of static friction between…

Q: A 15° wedge is forced into a saw cut to prevent binding of the circular saw. The coefficient of…

A: Given: The coefficient of static friction is μs=0.25. The magnitude of force P is P=30 lb. The…

Q: In the pivoted motor mount shown, the weight W of the 175-lb motor is used to maintain tension in…

A: Free Body Diagram of the given motor-mount set up is shown below:…

Q: Please solve asap

A: Apply the condition of the equilibrium  ∑MB=0r(TA-T)-M=0TA-T=Mr=300N.mm20mm=15N

Q: Block A supports a pipe column and rests as shown on wedge B . Knowing that the coefficient of…

A: Answer : Given parameters Coefficient of Friction,  μ = 0.25 Weight  = 3KN Least Force P = ?

Q: A 16-lb spool is at rest on an inclined surface. Around its center a cable is wound which travels…

A:

Q: A cable is placed around three parallel pipes. Two of the pipes are fixed and do not rotate; the…

A: Given, Coefficients of friction, μs=0.25,  μk=0.2

Q: a 1.2-m plank with a mass of 3kg rests on two joists. knowing that the coefficient of static…

A:

Q: Determine the maximum allowable value of weight W at rest. Knowing that the coefficient of static…

A:

Q: Block A supports a pipe column and rests as shown on wedge B. Knowing that the coefficient of static…

A: Given:-θ=45°μ=0.30To find:-Smallest force P

Q: Solve Prob. 8.19 assuming that the coefficients of friction at B are zero.(Reference to Problem…

A: Free body diagram

Q: Knowing that the coefficient of static friction between the tires and the road is 0.80 for the car…

A: Write the given data with suitable variables. μ=0.8v=360 in/ss=240 ing=386.08 in/s2

Q: Solve Prob. 8.93 assuming that the normal force per unit area between the disk and the floor varies…

A: Given Weight of the floor polisher,  Coefficient of kinetic friction,  Draw the diagram of the…

Q: The block and tackle shown are used to raise a 150-lb load. Each of the 3-in.-diameter pulleys…

A: According to principle of Kinematics, The total Upward and Downward forces are zero.

Q: The double pulley shown is attached to a 10-mm-radius shaft that fits loosely in a fixed bearing.…

A:

Q: Knowing that the coefficient of static friction between the tires and the road is 0.8 for the…

A:

Q: What weight W must be suspended through the fixed pulley shown to start motion to the left of the…

A: Given data The weight of the wedge A is WA=1500 N The weight of the wedge B is WB=3000 N The…

Q: The slender, uniform bar BC with a mass of 6 kg rests on the center of the 300x200 mm block of mass…

A:

Q: 3. (a) A 15 kg rod AB of length 2.5 m and a uniform cross section, is held in equilibrium as shown…

A: Angle of static friction(ϕs)⇒ It is the angle made by contact force with normal reaction when the…