Blowtorch is used to connect the two pipes together. Length of the pipe section shown is 150 cm with an inner diameter of 85 cm. The thickness of the pipe wall is 4 mm. The conductivity of the pipe section is 167 Wilm^2K. Environment has a temperature of 30 C and convective heat transfer coefficient of 28 WI(mC), find the required heat transfer to join the pipe sections at 220 C? HINT: Assume that the welding section is the base plate and the pipe is 1D extended surface (fin) symmetric about the torch melting line. Heat transfer happens by conduction along the pipe thíckness in horizontal direction and by convection to the environment. Length thickness Torch melting line 200 w 275 W none 314 W 453 W O O

Blowtorch is used to connect the two pipes together. Length of the pipe section shown is 150 cm with an inner diameter of 85 cm. The thickness of the pipe wall is 4 mm. The conductivity of the pipe section is 167 Wilm^2K. Environment has a temperature of 30 C and convective heat transfer coefficient of 28 WI(mC), find the required heat transfer to join the pipe sections at 220 C? HINT: Assume that the welding section is the base plate and the pipe is 1D extended surface (fin) symmetric about the torch melting line. Heat transfer happens by conduction along the pipe thíckness in horizontal direction and by convection to the environment. Length thickness Torch melting line 200 w 275 W none 314 W 453 W O O

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.49P

See similar textbooks

Similar questions

A 61 m rm of 203.2 mm pipe carrying 7.03 kg/cm^2 ga steam is drained by one steam trap. Find the capacity, kg per hr for running operation. The pipe is covered with insulation of 0.962 efficiency and is laid in a trench where the ambient ai temperature is probably 54.4 °C.
What is the extension of a straight rum of steel pipe 25.86 m long, if the installation temperature is 4.4 °C and normal operation on steam at 8.79 kg/cm^2 ga, saturated steam .
As part of an industrial pipe system a 6-meter-long by .5 meter inner diameter copper pipeweighing 200kg holds a lubricating oil in place while is heats from 20 deg C to 55 deg C. At thatpoint, the valve opens and allows to oil to flow through. What is the total heat transferrequired? And, what percentage of the heat transferred does the oil and copper each accountfor? (oil density = .9 kg/L , oil specific heat = 1800 J/kgC)
A rectangular heat exchanger is to be divided intosmaller sections using sheets of commercial steel0.4 mm thick, as sketched in Fig. The fl ow rate is20 kg/s of water at 20°C. Basic dimensions are L = 1 m,W = 20 cm, and H = 10 cm. What is the proper numberof square sections if the overall pressure drop is to be nomore than 1600 Pa?
spherical shaped vessel of 14 m outer diameter is 90 mm thick Find the rate of heat leakage, if the temperature difference between the inner and outer surfaces is 220°C Thermal conductivity of the material of the sphere is 0.083 W/mK
A 10 ft length of pipe with an inner radius of 1 in and outer radius of 1.25 in has an outer surface temperature of 250 F. The heat transfer rate is 30,000 BTU/hr. Find the interior surface temperature. Assume k = 25 BTU/hr-ft-F.
A constant heat flux of 40 W/cm² is applied from the outside to the three surfaces (top surface adiabatic) of a 6cmx6cm square pipe. Water enters the pipe at 25°C and its flow rate is 1 kg/s. If the length of the channel is 1.5 m, what will the outlet temperature of the water be? You can get the properties of water at 320K.
Milk is flowing through a heat exchanger at a rate of 2000 kg/h. The heat exchanger supplies 111,600 kJ/h. The outlet temperature of the product is 95℃. Determine the inlet temperature of the milk. The product specific heat is 3.9kJ/(kg℃). Show PBD and complete solution.
A pump delivers water between a reservoir and a water tank. The surface waterelevation of the water tank is 20m higher. The suction side contains an entrance strainer (Ks=2.5), and50m of PVC pipe that is 25cm in diameter. The discharge side includes a 200m long PVC pipe, 25 cmin diameter, and a gate valve. The net positive suction head (NPSH) is 7.5m, and the design discharge is150L/s. Determine the allowable elevation difference between the pump and the reservoir water surface,z s, to avoid cavitation. Assume a kinematic viscosity of 1x10-6m 2 /s and a specific weight of 9.79kN/m 3 .
A getter screen consists of a cylinder of length l = 0.3m, diameter d=0.25m and its circular based plate. The getter screen is cooled with liquid nitrogen and coated completely with deposited titanium providing a constantly fresh surface. Sticking probability s=1 for N2 and mean thermal velocity = 470m/s. Find the pumping speed.
Heat transfers Air is to be heated from 15 C to 270 C, as it flows through a tube 25mm diameter at average velocity 30 m/s. The tube surface is maintained at 280 C and the air is to be provided at rate 0.013 kg/s. Take the water properties k=0.0336 W/m.C , υ = 25.9× 10-6 m2/s , Cp=1.014 kJ/kg.C , ρ = 0.8826 kg/ m3 , Pr=0.689 . Determine the following The necessary tube length Heat transfer coefficient Heat transfer rate
a)Identifythe maximum velocitylimitof ammonia gas in the pipe if the flow is to be maintained as laminar flow. b)If the actual velocity of ammonia gas is 0.9 times the maximum velocitylimit, calculatethe heat transfer coefficient and heat transfer flux if the heat transfer area is 0.16m^2. c)Suppose the pipe has an outer diameter of 43.1 mm and the outer surface wall temperature of the pipe is 356 K, determinethe thermal resistance and thermal conductivity of the pipe.