bone fracture demands the use a bio-degradable implantplate with a lengthof 50mm and a width of 10mm.The healing timecorresponding to full bone reconstruction along with complete implant degradation (100% corrosion) is expected to be 1 year. The materialof choice for the implant is a magnesium alloy having a density of 1.8g/cm3and a corrosion penetration rate of CPR=1mm/year.Note the corrosion constant K=87.6. (a)What should be the implant plate thickness to meetthese requirements?(a)What can be done if the healing time will have to be increased for another 6months?Suggest and justify at least two opportunities.

bone fracture demands the use a bio-degradable implantplate with a lengthof 50mm and a width of 10mm.The healing timecorresponding to full bone reconstruction along with complete implant degradation (100% corrosion) is expected to be 1 year. The materialof choice for the implant is a magnesium alloy having a density of 1.8g/cm3and a corrosion penetration rate of CPR=1mm/year.Note the corrosion constant K=87.6. (a)What should be the implant plate thickness to meetthese requirements?(a)What can be done if the healing time will have to be increased for another 6months?Suggest and justify at least two opportunities.

Principles of Instrumental Analysis

7th Edition

ISBN:9781305577213

Author:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Publisher:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Chapter5: Signals And Noise

Section: Chapter Questions

Problem 5.4QAP

See similar textbooks

Similar questions

A steel sheet will have a thin layer of zinc put on one side to protect it from corrosion. Determination of the zinc film thickness per one centimeter square of steel sheet when a 2 A current is employed and the electrolytic deposition process is completed in exactly 30 minutes at 25 degrees Celsius. With a 1 M zinc solution, it's safe to presume that its concentration will remain stable throughout the process.
A thin film of zinc is to be deposited on one side of a steel sheet. Determine the zinc film thickness per 1cm2 of steel sheet if 2 A current was used and the electrolytic deposition process was done for exactly 30 minutes at 25oC. The zinc solution has a concentration of 1 M and can be assumed to be constant throughout the process.
A thin film of zinc is to be deposited on one side of a steel sheet. Determine the zinc film thickness per 1cm2 of steel sheet if 2 A current was used and the electrolytic deposition process was done for exactly 30 minutes at 25oC. The zinc solution has a concentration of 1 M and can be assumed to be constant throughout the process. pls explain the solution shown in the figure thoroughly or you can come up with your own thank you
Knowing that an electroplating industry wants to coat a steel sheet with a layer of metallic Cu by an electrodeposition process, what is the time to deposit a 50 μm layer on a 10 cm2 plate applying a current density of 30 mA /cm2 if process efficiency is 75%.
.A conductance cell filled with 0.01 M solution of an electrolyte offered a resistance of 2300 ohms. If the electrodes of the cell are 1.90 cm apart and have an area of cross-section equal to 4.70 sq cm, calculate specific conductance Calculate molar activity
In the video "Sacrificial Anode Materials Demo", which among Zn, Al, Mg served as as i) sacrificial anodes? and ii) as noble coatings?
Silver is uniformly electro-deposited on a metallic vessel of surface area of 900 cm2 by passing a current of 0.5 ampere for 2 hours. Calculate the thickness of silver deposited.[Given: the density of silver is 10.5 g cm-3 and atomic mass of Ag = 108 amu.]
The maximum corrosion current density in a steel sheet coated with zinc and exposed to seawater is found to be 5 mA/m². What thickness of the layer is necessary so that the coating may last for one year?
Two Copper strips were used to determine the effect of electrolysis time and immersed in 3.080g of Cu (NO3)2 dissolved in 25mL of DI water. The weight of one copper strip act as an anode is taken before the reaction and after the reaction to calculate the change in mass. 1.0A of current and 7.50 V is used throughout the experiment Calculate the theoretical mass that should be obtained at each time interval and Compares the theoretical mass (mg) of copper and the actual mass deposited (obtained from the electrolysis, ∆m) by calculating the %error at different times. Briefly discuss the observed results. Is there any trend observed? Positive Anode (Copper strip): Cu(solid) ®Cu2+(aqueous)+2e- Negative Cathode(Copper strip ): Cu2+(aqueous)+2e- ®Cu(solid) Time interval (min) 2.5 5.0 7.5 10 Initial mass of strip (mg) 3432 3390 3297 3141 Final mass of strip (mg) 3390 3297 3141 2939 Mass change Dm (mg) 44 93 156 202 Michael Faraday…
The _____ in a _____ voltammogram is related to the ____ a. limiting current, cyclic, concentration of the analyte of interest b. limiting current , linear sweep, concentration of the analyte of interest c. peak current cyclic, standard reduction potential of the analyte of interest d. peak current , linear sweep, standard reduction potential of the analyte of interest e. none of these
How long would it take to plate 6.49 g of nickel onto copper using a 2.0 V power supply with a 437 mA current flow and 0.50 M nickel (II) acetate solution? time in (hr)
Explain how cyclic voltammetry works and how it forms a cyclic voltammogram - what does this tell us?