The limiting current was observed to be 74.9 pA in the voltammogram for a 40.0 ml. solution of 0.00694M Cu. The current in the limiting-current region was continued for 54.6 min. Calculate the percentage decrease in the concentration of the solution. 54 percentage decrease: Enter numeric value ncoect

The limiting current was observed to be 74.9 pA in the voltammogram for a 40.0 ml. solution of 0.00694M Cu. The current in the limiting-current region was continued for 54.6 min. Calculate the percentage decrease in the concentration of the solution. 54 percentage decrease: Enter numeric value ncoect

Appl Of Ms Excel In Analytical Chemistry

2nd Edition

ISBN:9781285686691

Author:Crouch

Publisher:Crouch

Chapter11: Dynamic Electrochemistry

Section: Chapter Questions

Problem 6P

See similar textbooks

Similar questions

Copper was electroplated from a Cu2SO4 solution onto an electrode with an active surface area of 6.96 cm2. Determine the thickness (mm) of the deposit if the current is kept constant at 3.55 A for 1.0266 hours. (density of Cu = 8.96 g/cm3, MW of Cu = 63.55 g/mol). (Input values only with 2 decimal places. Do not include the unit.)
Copper was electroplated from a Cu2SO4 solution onto an electrode with an active surface area of 3.83 cm2. Determine the thickness (mm) of the deposit if the current is kept constant at 3.94 A for 1.4466 hours. (density of Cu = 8.96 g/cm3, MW of Cu = 63.55g/mol). Input values only with 2 decimal places. Do not include the unit.
Name the advantages of glass electrode in potentiometric measurements (please write correctly and concisely).
A thin film of zinc is to be deposited on one side of a steel sheet. Determine the zinc film thickness per 1cm2 of steel sheet if 2 A current was used and the electrolytic deposition process was done for exactly 30 minutes at 25oC. The zinc solution has a concentration of 1 M and can be assumed to be constant throughout the process. pls explain the solution shown in the figure thoroughly or you can come up with your own thank you
An ion-selective electrode (ISE) produces voltage output (mV) proportional to solution pH. You have three standard pH solutions (4, 7, and 10). Assuming that pH 7 buffer solution is used together with pH 4 for calibration prior to measuring acidic solutions and together with pH 10 before measuring alkaline solutions, produce a flowchart of the calibration routine for a single pH ISE.
The purity of a sample of K3Fe(CN)6 is determined using hydrodynamic voltammetry at a glassy carbon electrode. The following data were obtained for a set of calibration standards. A sample of impure K3Fe(CN)6 is prepared for analysis by diluting a 0.264 g portion to volume in a 100 mL volumetric flask. The limiting current for the sample is 444 μA. a) What type of calibration method is used? (Internal Standard, External Standard, or Standard Addition?) b) What is the purity of this sample of K3Fe(CN)6 (FW=329.25 g/mol)?
An atomic beam is designed to function with (a) cadmium, (b) mercury. The source is an oven maintained at 380K with a small slit of dimensions 1.0cm x 1.0 x 10-3cm. The vapor pressure of cadmium is 0.13 Pa nd that of mercury is 12 Pa at this temperature. What is the atomic current (the number of atoms per second) in the beams?
An unknown cadmium(II) solution was analyzed. A 25.00-mL sample of the unknown solution produced a diffusion current of 1.86 mA. Following addition of a 5.00-mL aliquot of 0.00212 M Cd2+ standard solution to the unknown solution, a diffusion current of 5.27 mA was produced. A) What type of electroanalytical method was used? B) What type of calibration method was used? C) What is the molar concentration of Cd2+ in the unknown solution?
For a nitrate ion selective electrode, the selectivity factor for nitrite over nitrate is 0.062 and that for nitrate over perchlorate is 990. What is the percent error in the measurement of a 1.50 mM nitrate solution in the presence of each interfering ion at a concentration of 0.10 mM? Please answer very soon will give rating surely Complete Answer needed
If the electrode bias voltage is 0 volts, what would the output be given that it is a Clark oxygen electrode? i) Iout is 0 A for all oxygen concentrations ii) Vout 0 V for all oxygen concentrations iii) Output current would be the same for all oxygen concentration
ELECTROCHEMISTRY: Copper was electroplated from a Cu2SO4 solution onto an electrode with an active surface area of 3.34 cm2. Determine the thickness (mm) of the deposit if the current is kept constant at 4.94 A for 1.022 hours. (density of Cu = 8.96 g/cm3, MW of Cu = 63.55 g/mol). (Input values only with 2 decimal places. Do not include the unit.)
Calculate the required voltage (V) if an unknown metal (M) was electrodeposited from an aqueous solution containing M2X1 (where X is the anion) with a supplied current of 4.98 A for 11 h, consuming 0.1145 kWh of electrical energy. Assume that the current efficiency is 93%. (Input values only with 2 decimal places. Do not include the unit.)