I need answer as soon as possible Oil in hydraulic cylinder is compressed from aninitial volume 3 m³ to 1.92 m³. If the pressure ofoil in the cylinder changes from 30 to 80 MParespectiveley during compression. Determinebulk modulus of elasticity of oil ?

Given data: V1=3 m3 P1=30 MPaV2=1.92 m3 P2=80 MPaSo,Acc. to question,Oil in…

Answered: bulk modulus of elasticity of oil ?

Engineering

Mechanical Engineering

bulk modulus of elasticity of oil ?

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.122P: The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate...

See similar textbooks

Related questions

Q: A vibratory system consists of a mass 17.5 kg, a spring of stiffness 1350 N/m, and a dashpot with da...

Q: A thin-walled closed cylinder (radius r of 400 mm; wall thickness t of 20 mm), is simultaneously sub...

A: Solution: Given Data: r = 400 mm t = 20 mm P = 1.2 MPa T = 100 kN-m FOS = 2.8

Q: In the figure shown, an open tank tube is attached to a tank. If the water rises to a height of 800m...

Q: A fireworks show is choreographed to have two shells cross paths at a height of 117 feet and explode...

A: Given:h=117 ftθ=68o

Q: 1. The absolute pressure at some point is equal to 0.4at(engineering atmospheres pressure), the rela...

A: 1). P(absolute)=P(relative)+P(atm) 0.4atm=P(relative)+1atm P(relative/gauge)=-0.6atm Option A is cor...

Q: Find the refrigeration capacity (in TR ) required to cool 29 m³/min from 29°C to 18°C if air from th...

Q: 2. Link BD is made of brass ( E = 103 GPa ) and has a cross-sectional area of 258 mm?. Link CE is ma...

Q: The crane BC shown below lifts a load of W. Neglecting the weight of the crane. Determine the follow...

Q: The following represents stress measured in the global coordinate system [10 (X1, X2, X3) as o = |20...

Q: 20. Assume that the valve timing diagram of a Cadilac engine shows the intake valve opened for a per...

Q: The winch in the figure is used to move the 135 kg uniform log. The coefficient of static friction b...

Q: A nylon material has a fracture toughness K1c = 2.1 MPa.m1/2 It follows a Paris Law for fatigue with...

A: Given : K = 2.1 Mpa.m1/2 C = 4 x 10-8 n = 3.2 N = 63387 To find a

Q: A wind tunnel has an incompressible flow of air, flowing horizontally from an inlet section, 7 times...

Q: A clamping vice uses a single acting cylinder to clamp the work-pieces. Determine the extend force i...

Q: 3. A car traveling at 20 m/s when the driver sees a child standing in the road. He takes 0.80 s to r...

Q: 1. Replace the loading acting on the beam by an equivalent force and a couple moment at point O. ...

Q: The basketball player likes to release his foul shots with an initial speed vo = 25.5 ft/sec. What 2...

A: Given: vo=25.5 ft/s

Q: A Kaplan turbine works under a head of 10 m. The design speed is 50 rpm and turbine develops 40000 k...

A: Given that, H=10 m, N=50 rpm, P=40000 kW, Q=550 m3/s

Q: Problem 6.5 - Locate the centroid of the plan area shown by integrati D D o d d d x = 4 – x = 3y 3 m...

A: Given: The plane area is given below,

Q: 1. A stone is dropped down a well and 5 sec later the sound of the splash is heard. If the velocity ...

A: Time of splash sound, T=5 secVelocity of sound, V=1120 ft/sec

Q: Inatwo-dimensional tug-of-war, Alex, Betty, and Charles pull harizantally on an automohile tire at t...

Q: What is the column (small, intermediate or long) if the radius of gyration is greater than the allow...

A: A column is a vertical member which is subjected to axial compressive load and failure of the column...

Q: An unknown hydrocarbon fuel, burned in air, has the following Orsat analysis: Carbon Dioxide 12.5% C...

A: Given data Carbon dioxide percentage = 12.5%Carbon Monoxide percentage = 0.3%Oxygen percentage = 3.1...

Q: What is the direction of the acceleration of the pendulum bob A at the instant shown in the figure?

A: The pendulum starts from the right side of O. And it had reachend 12.5 ° downwards. As it falls from...

Q: determine the water-

A: To find Water depth after jump

Q: heat from a small motorcycle engine. If the average engine surface temperature is 112 C, Exercise 4....

A: Given: The inner diameter of fin, d = 20 cm = 0.2 m The outer diameter of fin, D = 26 cm = 0.26 m Th...

Q: natural frequency of the system.

A: Given: A mass of 1 kg, m=1 kgAttached to two identical springs each of stiffness; k=25 kN/mUnder fr...

Q: Assume that after removing the cylinder head of an engine, a wet, oily condition is noticed on the b...

Q: The Truck A is used to hoist the block B with the pulley system in the figure. If A has a forward ve...

Q: What is the mass flow rate flowing through the boiler?

Q: The velocity of a particle moving in the x-y plane is given by (6.00i + 4.94j) m/s at time t = 5.61 ...

Q: car travelling at 20 m/sec applies the brake and comes to rest in 6 seconds. Determine the accelerat...

A: Given Data vo=20 m/s vf=0 t=6 sec

Q: 1. In a Rankine cycle, steam enters the turbine at 2.5 MPa and condenser at 50 kPa, what is the ther...

Q: A force of 50 kN has two components, F₁ = 30 kN and F₂ = 60 kN. Determine the angle that F, makes wi...

Q: determine the temperature distribution along the fin surface. The thermal conductivity of the heat f...

Q: Problem (5.2) An impulse turbine has a number of pressure stages (pressure compounded turbine). The ...

Q: Copper wire has a resistivity ρ = 1.7 × 10-8 Ω⋅m when at 20°C and it has a temperature coefficient α...

Q: Since Lucas is an engineer familiar with thermodynamics. He decided to create his own heat engine at...

Q: A weather report indicates the barometric pressure is 28.54 in of mercury. What is the atmospheric p...

A: Given Data Pb=28.54 in of Hg

Q: 1. A vibration isolation unit consists of two blocks of hard rubber bonded to plate AB and to rigid ...

Q: A steel rod of diameter 10 mm carries an axial load of 10 kN. Consider the modulus of elasticity and...

Q: 12. A signal no. 1 storm is up in your area, and the weather sirens are turned on to give warning to...

Q: 2 - Explain the bonding, hybridization and geometry of carbon nanotubes that are used to help store ...

A: Introduction: carbon nano tubes are in the form of cyliders. It can be made by the graphine sheet by...

Q: A wind turbine has a blade length of 30 m. In a given day, average speed of wind for 5 hours is 9 m/...

Q: An Ideal Regenerative Rankine cycle operates on a boiler pressure of 10MPa. Steam leaves the boiler ...

Q: A. Clockwise moments N.M B. Counterclockwise moments N.M C. Net moments about point ( 0) N.M D Net M...

Q: The particle P starts from rest at point A at time t = 0 and changes its speed thereafter at a const...

Q: Required information A steel bar (Es= 210 GPa) and an aluminum bar (Ea = 70 GPa) are bonded together...

Q: A supersonic flow at M = 3, T1 = 295 K, and pi = 3 atm is deflected upward through a compression cor...

Q: 1.6.10If the component of force P parallel to the incline is 400 N, determine the value of P and its...

Question

I need answer as soon as possible

Oil in hydraulic cylinder is compressed from an
initial volume 3 m³ to 1.92 m³. If the pressure of
oil in the cylinder changes from 30 to 80 MPa
respectiveley during compression. Determine
bulk modulus of elasticity of oil ?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

What is the pressure at the bottom of 0.5m height fluid if the container moves 5m/s2 upward? Fluid has a density of 2000kg/m3 a. 13665Pab. 13258Pac. 14810Pad. 16145Pa
The truck carries an open rectangular container that is 3.9m wide, 3.0m deep and 5.0m long, contains oil of density 811kg/m³ to a depth of 2.1m. If it has a constant acceleration of 6.9m/s². Determine the total force(in kN) acting at the rear wall of the container.
A thin spherical shell in diameter with its wall of 1.2 cm thickness is filled with a fluid at atmospheric pressure. What intensity of pressure will be developed in it if 175 cm3 more of fluid is pumped into it? Also, calculate the circumferential stress at that pressure and the increase in diameter. Take E = 200 GN/m2, and 1/m = 0.3.
An oil tanker 3m wide 2 m deep and 10 m long contains oil of density 800 kg/m3, if the tanker is closed and completely filled with the oil and accelerated horizontally at 3m/s2. a.) determine the total liquid thrust (hydrostatic force) on the front end. (in kN) b.) determine the total liquid thrust (hydrostatic force) on the rear end. (in kN)
ii. If the surface tension of the drop be 42.27x103 N/m, find the pressure difference of the drop
To what height will 68˚F ethyl alcohol rise in a 0.005 in internal diameter glass capillary tube? The density of the alcohol is 49 lbm/ft3 note ? = 0.00156 ???/ ?? and ? = 0°.
A circular tank with a diameter of 4.5m is filled with two immiscible fluids. Water to a depth of 3m andoil with a relative density of 0,9 to a depth of 2mDetermine the Hydrostatic force acting on the verticalside of the tank and the position of the centre of pressure from the oil-free surface.
A hydraulic cylinder filled with water has an inside diameter of 1.0 in and a length of 2.0 ft. How many pounds of force must be applied to a piston at the end of the cylinder to compress the water by 0.1 in? Take the bulk modulus of water to be K=312,000 psi.
An open tank 2 m x 4 m rectangular horizontal section has anegligible weight and contains water to a depth of 1.5 m. It is actedupon by an unbalanced force of 50 kN parallel to longer side so thatwater is about to spill. If the tank is closed and theacceleration is increased by 4 m/s ², determine the new unbalancedforce if the pressure on the surface is 30 kPa.
he gage pressure of the air in the tank shown in the figure is measured to be 65 kPa. Determine the differential height h of the mercury column.
The 100cm radius cylinder weighs 3.1 KN and rest on the bottom of a container which is 1.5 meter long. Oil and water are poured into the left and right portion of the container to the depth of 0.8m and 1.4m respectively. Find the magnitude of the horizontal and vertical components of the force which will keep the cylinder touching the container at B.
An experiment was conducted using a communicating vessel to knowthehydraulic pressure. The communicating vessel consists of two column, XandY. Column X has a diameter of 15 cm and column Y of 75 cm. Oil (s = 0.852) wasfilled to the communicating vessel. A load of 1275 N was given to the columnY. Determine the minimum force that should be given to column Xso that theload can be lifted and the density of oil !