By using Gauss-Siedal method, the voltage of the bus 2 after two iteration is Your answer By using Gauss-Siedal method the voltage of the bus 3 after two iteration is Your answer For a system consist from 3 buses and bus 1 is the slack bus. The data of the system are:- 0.25 -0.2 -0.05 Ybus =j-0.2 0.225 -0.025 p.u. -0.05 -0.025 0.075 V₁=1+j0 p.u., P₂+jQ2-0.6+j0.25 p.u., P3+jQ=0.8+j0.5 p.u.

By using Gauss-Siedal method, the voltage of the bus 2 after two iteration is Your answer By using Gauss-Siedal method the voltage of the bus 3 after two iteration is Your answer For a system consist from 3 buses and bus 1 is the slack bus. The data of the system are:- 0.25 -0.2 -0.05 Ybus =j-0.2 0.225 -0.025 p.u. -0.05 -0.025 0.075 V₁=1+j0 p.u., P₂+jQ2-0.6+j0.25 p.u., P3+jQ=0.8+j0.5 p.u.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.34P

See similar textbooks

Similar questions

For an NN square matrix A, in (N1) steps, the technique of Gauss elimination can transform into an ____________ matrix.
Expand 6k=13m=12Dkm.
For the system in Figure 4 with given generation and load dispatch determine the voltages after two itterations of Gauss-Seidel method. Assume the initial voltage to be 1.01 at angle of 0◦ pu at bus 1, 1.015 at angle of 0◦ pu at bus 2, and 1.0 at angle of 0◦ pu at bus 3. All line impedances are in per unit on a common base, and charging is neglected. Take base power of 100 MVA.
The figure below shows the one-line diagram of a simple three-bus power system withgeneration at bus 1. The voltage at bus 1 is V1 = 1.0∠0°per unit. The scheduledloads on buses 2 and 3 are marked on the diagram. Line impedances are marked inper unit on a 100 MVA base.(a) Using Gauss-Seidel method and initial estimates of ?2(0) = 1.0 + ?0, ?3(0) = 1.0 + ?0, determine V2and V3. Perform two iterations.(b) If after several iterations the bus voltages converge to?2 = 0.90 − ?0.10 pu?3 = 0.95 − ?0.05 pudetermine the line flows and line losses and the slack bus real and reactive power.
Using Nyquist criterion, how counter-clockwise encirclements of -1 made by mapping are in the given system below?
3. Which one of the following method uses weak coupling between reactive power and voltage angle?. A. Newton - Raphson Method B. Decoupled Method C. Gauss-Seidal Method
Give two advantages and one disadvantage of fast decoupled load flow method over Newton-Raphson method. What simplification of the Jacobin matrix can be made in first decoupled?
Figure 5 shows a single-line diagram of a three-bus power system. Power flow input data are givenin Tables 1 and 2. (a) Determine the Ybus Matrix (b) Use Gauss-Seidel method to compute V2(1) and V3(1), the phase voltages at bus 2 and 3 after the first iteration. Use zero initial phase angles and 1.0 per-unit initial bus voltage magnitudes.
Does RTD have a treshold and a dead space? If yes, explain them.
Draw the phasor diagrams for a transmission line (modeled as short transmission line) when supplying a leading, lagging and unity power factor loads. Phasor diagram should include sending end voltage, receiving end voltage, load power factor, and line current. Based on the phasors answer the following: a. For lagging power factor load, is |??| >|??|? True/Falseb. For leading power factor load, is |??| >|??|? True/Falsec. For unity power factor load, is |??| >|??|? True/False
Discuss the advantages and limitations of Gauss-Seidal and Newton Raphson methods . Of this two, which method is generally preferred for solving the load flow problems?
A single-line diagram of a four-bus system is shown in fiugre. Equipment ratings and per-unit reactances are given as follows.Machines 1 and 2: 100 MVA 20 kV; X1= X2 = 0.2; X0= 0.04 Xn= 0.05 Transformers T1 and T2: 100 MVA 20Y/345Y kV; X1 = X2 = X0 = 0.08. On a base of 100 MVA and 345 kV in the zone of the transmission line, the series reactances of the transmission line are X1 = X2 = 0.15 and X0=0.5 per unit. (a) Determine the bus impedance matrix for each of the three sequence networks. (b) Assume the system to be operating at nominal system voltage without prefault currents when a bolted single-line-toground fault occurs on phase A at bus 3. Compute the fault current, the current out of phase C of machine 2 during the fault, and the line-toground voltages at the terminals of machine 2 during the fault. Total detailed answer is needed. The figure is attached.