c) A gas with a molecular weight of 4 and a specific heat ratio of 1.67 flows through a variable area duct. At some point in the flow the velocity is 180m/s and the temperature is 10°C. At some other point in the flow, the temperature is -10°C. Find the velocity at this point in the flow assuming that the flow is adiabatic

c) A gas with a molecular weight of 4 and a specific heat ratio of 1.67 flows through a variable area duct. At some point in the flow the velocity is 180m/s and the temperature is 10°C. At some other point in the flow, the temperature is -10°C. Find the velocity at this point in the flow assuming that the flow is adiabatic

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An airplane is flying at a velocity of 150 m/s at standard sea-level conditions. The temperature at a point on the wing is 270K. What is the pressure and velocity at that point? For air, C, = 1008- %3D kg K
Consider the fluid flow between two large plates at a distance L from each other. While the top plate is motionless and insulated from these plates, the bottom plate moves with a constant velocity V. It moves and is kept at temperature T0. General continuity, momentum and energy equations, simplifying these equations and solving for each separately Obtain a relation for the temperature of the fluid. In addition, the maximum Find where the temperature is formed and find its value.
Air flows steadily at a pressure of 105 kPa at a speed of 0.1m / s and a temperature of 300K in a duct with a diameter of 10 cm. After a deformation in the duct, the flow is uniformly out of the gap with dimensions of 3cm × 6cm out of the possible state. Act like a complete gas, you can make R = 287J / kg.k Assuming an incompressible flow, calculate the velocity of air out of the gap.
Brine is flowing through a coil with a velocity of 240 fpm, The pressure foss in overcoming me traction in the coil 3.134 psia. The diameter of the coil is 3 ft and it has internal diameter of 1.20 inches At 86 degree Fahrenheit, the density of the brine is 995.6262 kg/m and its viscosity is 0.10081067 PA. a.) Calculate for the fanning friction factor in problem. b.) Determine the number of turns of the coil.
Q4. Water is flowing in AF pipe (Figure 1) at a velocity of 2 m/s and a pressure of 102400 Pa, the pipe length is 100 m. If the water pressure needs to be at a pressure of 1.6 atm on a lower level. What should be the different in elevation between the upper and lower levels in order to achieve this pressure? Take the density of water 1000 kg/m and gravity is 9.81 m/s, consider the energy loss.
How much air is used per kg of coal burnt in a boiler having a chimney of 31.1 m height to create a draught of 19 mm of the water column when the temperature of the flue gases in the chimney is 361 o C and the temperature of the boiler house is 28.4 o C. Also find the equivalent gas head of the chimney.
Question 2: A fluid with density 1 kg/m' is moving through a pipe with same cross-sectional area at a velocity of 1.2 m/s at pointl and 1.5 m/s at point 2, and point 2 above point 1 in the elevation with 3 cm. If the pressure at the beginning at point lis 116 Pa, what is the pressure of fluid at point 2? What is the mass and volume flow rate at point 2? 2 1
3. In figure shown, pipes 1 and 2 are of diameter 3 cm, D3 = 4 cm. Alcohol (SG = 0.80) enters section 1 at 6 m/s while water enters at section 2 at 10 m/s. Assuming ideal mixing of incompressible fluids, compute the exit velocity and density of the mixture at section 3. The temperature is 20°C. Answer: 9 m/s, 928 kg/m3 (2) Ideal mixing (3) V₂-P3
could you please help me calculate theheigth in metres of the fluid at time t= 100s
Find an expression for the mass flux in the venturi tube (shown below) as a function of the pressure change.
(4) A water hose connected to a nozzle is used to fill a 10 L container. The internal diameter of the hose is 2 cm and the nozzle exit has an inner diameter of 1.7 cm. It takes 30 s to fill up the container. If the inlet pressure is 2 atm and the nozzle exit is 0.8 m above the hosea. What is the velocity (m/s) of water at the outlet stream and at the inlet stream?b. What is the water pressure (atm) at the outlet stream c. What is the mass flow rate of water (kg/s)?
Hot water at a constant volumetric flow rate of Fh and temperature Th(t) is mixed with cold water at a constant volumetric flow rate of Fc and a constant temperature of Tc. Both streams flow into a bathtub, but because of carelessness, the water is overflowing and keeping the bathtub full of water. The bathtub volume is V, and the heat loss can be ignored. Assuming the water in the bathtub is perfectly mixed and constant density and heat capacity, derive the differential equation relating the temperature in the bathtub, T(t), to the temperature of the hot water, Th(t).