A fluid with density 1 kg/m' is moving through a pipe with same cross-sectional area at a velocity of 1.2 m/s at pointl and 1.5 m/s at point 2, and point 2 above point 1 in the elevation with 3 cm. If the pressure at the beginning at point lis 116 Pa, what is the pressure of fluid at point 2? What is the mass and volume flow rate at point 2? 2 1

A fluid with density 1 kg/m' is moving through a pipe with same cross-sectional area at a velocity of 1.2 m/s at pointl and 1.5 m/s at point 2, and point 2 above point 1 in the elevation with 3 cm. If the pressure at the beginning at point lis 116 Pa, what is the pressure of fluid at point 2? What is the mass and volume flow rate at point 2? 2 1

Name: Question 2:A fluid with density 1 kg/m' is moving through a pipe with
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Question 2:A fluid with density 1 kg/m' is moving through a pipe with same cross-sectional area at avelocity of 1.2 m/s at pointl and 1.5 m/s at point 2, and point 2 above point 1 in the elevationwith 3 cm. If the pressure at the beginning at point

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pump is discharging 12 liters/sec of water through 10 cm diameter pipe. When the pressure on the discharge side of the pump is 700 kPa, what pressure can be expected in the discharge pipe at a point 540 m distant from the pump and 45 m higher in elevation. Use n = 0.015.
A medical syringe (shown below) is used to inject a patient with a local anaesthetic before performing outpatient surgery. The anaesthetic can be modeled as an incompressible fluid with specific gravity, S = 1.02. Determine the plunger velocity, in units of in/s, if the anaesthetic is to be delivered at a constant 7 cm3 s −1 when the syringe is modeled as being perfectly sealed, and there is backward leakage between the plunger and syringe at a rate of 10% of the volume flow rate delivered through the needle. Note that anaesthetic is still to be delivered to the patient at 7 cm3 s −1 , despite this leakage.
Consider coolant in a circular pipe to be in laminar flow; the following formula gives one-dimensional velocity: V=Vmax*(1-((r/R)^2)) Vmax = 2 m/s R = Radius of Pipe = 0.05 m Fluid Density (uniform) = 300 kg/m^3 1. What is the coolant flow (m^3/s)? 2. What is the coolant average velocity in the pipe (m/s)? 3. What is the true kinetic head of flow expression?
The pressure in a section of a horizontal pipe of diameter d1 = 2.0 cm is p1 = 142 kPa. The water flows through the pipe at a volumetric flow rate V = 2.8 L/s. If the pressure at a certain point is reduced to p2 = 42.6 kPa, due to a throttling of a pipe section, what should the diameter d2 of the throttling section be? Consider the density of water ρ = 1.0 g/cm3. Choose the correct option:
In a horizontal pipe water flows at a rate of 9.1 L/s. Here, the pipe has two sections, one with a diameter of 10.16 cm and the other with a diameter of 5.08 cm, with a gradual smooth reducing section. In this case, a mercury manometer is used to measure the pressure difference. If friction is negligible how would I find the differential height of mercury between the two sections? If the manometer on the 5.08cm pipe section was replaced with a pitot tube how would the reading change? any help would be deeply appreciated
Water flows through a pipe of 0.0025 m^2size with a uniform velocity of 7m/s and flows out from an ariface at bottom at a rate 0.003 m^3/s. what is rate of change of mass of water in the tank?
If the difference between the total pressure and static pressure in an air duct is measured by a pitot tube to be 6.5 cm H2O, what is the flow velocity in m/s? Density of water is 998 kg/m3, and g = 9.81 m/s2. 3 signififcant figures answer
Water enters a shower head through a pipe of internal radius r = 6.4 mm, and leaves through 30 small holes, each of radius r1 = 0.08 mm. When the faucet is opened, the water moves in the tube at a speed of 90 cm/s. What is the volumetric flow of the shower head in liters per second?
A 6.0 cm diameter horizontal pipe gradually narrows to 4.5 cm. When water flows through this pipe at a certain rate, the gauge pressure in these two sections is 33.5 kPa and 22.6 kPa, respectively. What is the volume rate of flow?
The entrance-to-exit area ratio of streamtube is given as 2. Consider incompressible flow entering the streamtube. Which of the following statements is true? A. mass flow decreases and static pressure decreases B. mass flow decreases and static pressure increases C. mass flow remains unchanged and velocity of the flow decreases D. mass flow remains unchanged and velocity of the flow increases
A jet of water, issuing from sharp-edged vertical orifice under a constant head of 60 cm , has the horizontal and vertical coordinates measured from vena contracta at a certain point as 10. cm and 0.45 cm respevtively. Find Cc if Cd= 0.60.include your free body diagrama.0.612 b.0.962 c.0.98 d.0.623
The head loss for a certain circular pipe is given by hL = 0.0826fL(V.2/D5), where f is the friction factor (dimensionless), L is the pipe length, V. is the volumetric flow rate, and D is the pipe diameter. Determine if the 0.0826 is a dimensional or dimensionless constant. Is this equation dimen sionally homogeneous as it stands?