(c) Given the end area of cut and fill of soil as in Table Q4(c). If the material bulks after excavation about 10% and shrink 12%. Given, distance between chainage is 100 m. Draw the mass haul diagram and estimate how much excess cut or fill is required.

(c) Given the end area of cut and fill of soil as in Table Q4(c). If the material bulks after excavation about 10% and shrink 12%. Given, distance between chainage is 100 m. Draw the mass haul diagram and estimate how much excess cut or fill is required.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Find the expected production in loose cubic meters (LCM) per hour of a large hydraulic excavator.…

A: given data: sand and gravel soil Bucket fill factor(F)=0.95 average depth of cut=2.5 m maximum depth…

Q: You are a civil engineer who has been given the task to monitor the excavation of road construction.…

Q: Q3- Find the production rate of the crawler-tractor-mounted loader shown in Figure, Using the…

A: Cycle time per load in minutes Fixed time(load,shift,turn and dump) Time=0.4 Haul…

Q: Q1: In construction of a highway section, the earthwork information is available as shown in the…

A: Given: A highway section, the earthwork information is available as shown in the table below.…

Q: An excavation of 25,750 m3 (bm) is to be made for the foundation excavation of a building in 5 weeks…

A: Volume of earthwork to be excavated, V=25750 m3 Initial working days=5 weeks×6 days=30 days Workdays…

Q: You are a civil engineer who has been given the task to monitor the excavation of a road…

Q: Following is the variation of N60 with depth in a granular soil deposit. A concrete pile 9 m long…

A: It is required to determine the average value of standard penetration resistance.…

Q: A single summit mass diagram has the following properties: Free haul: Length = 50 m, Mass ordinate =…

A: Total cost =Cost of haul×VOlume×Length+Cost of Economic haul×VOlume×Length

Q: Find the expected production in loose cubic meters (LCM) per hour of a large hydraulic excavator.…

A: Question is based on the large hydraulic excavator . Bucket capacity, job efficiency, average and…

Q: You are a civil engineer who has been given the task to monitor the excavation of road construction.…

Q: Given the end area of cut and fill of soil as in Table Q4(c). If the material bulks after excavation…

A: Data Given: Bulks after excavation = 10% Shrink = 12% Chainage distance = 100m Asked: Draw Mass…

Q: Briefly discuss the advantages of preloading methods?

A: The technique of pre loading was developed and is mainly was used in the projects connected to…

Q: A sack slides off the ramp with a horizontal velocity of 12 m/s. If the height of the ramp is 6 m…

Q: Determine mass diagram ordinates given is the net fill and cut volumes and calculate overhaul…

A: Solution: Given data: The net fills and cut volumes are given: The free haul distance=250 m

Q: 1. What is the stationing of the end of excavation? 2. Find the volume of fill by end area method.…

Q: A natural site will be excavated to bring soil to backfill a 500m³ pit,Ks=1.2,K's=1.03.(1) Calculate…

A: Volume of the pit(Vp)=500 m3 Void ratio of pit filled with soil=1.2 Void ratio of excavated…

Q: Question 3 An ASD downward column load of 500 k is to be supported on a group of drilled…

A: Column Load = 500 kips Depth of groundwater table = 15 ft. Details of stratification:

Q: Given the following end areas for cut and fill, complete the earthwork calculation using a shrinkage…

Q: The areas of the cross-section of an excavation is 4 567.80 sq.m, 3 456.90 sq.m, and 3 876.30 sq.m.…

A: Introduction- The practice, profession, art, and science of identifying the terrestrial or…

Q: The given data of a proposed road is tabulated below. The free haul distance is 50m and the cost of…

A: The volume of the overhauled material is measured by multiplying the overhaul distance by the cubic…

Q: An excavation of 25,750 m3 (bm) is to be made for the foundation excavation of a building in 5 weeks…

A: The total quantity of earthwork is 25750 m3 Total working days in the 5 weeks are 6 days =5×6=30…

Q: The areas of the cross-section of an excavation are 3,987.23 sqm, 4,659.01 sqm, and 3,876.30 sqm.…

Q: SHOW FIGURE Given the following sections: Station 2 + 020 a 0 b +2.5 +3.15 +2.65 Station 2 + 080…

Q: A small hydraulic excavator will be used to dig a trench in hard clay (bucket fill factor = 0.80).…

A: Excavator is a power-driven digging machine used to excavate earth for different purposes.…

Q: Given: A small hydraulic excavator will be used to dig a trench in common earth (bucket fill factor…

A: Consider the following given data The soil type is common earth Bucket fill factor=B=0.95Trench…

Q: shrinkage of 20 %.

Q: In an earthwork computation , the results shown that the length of free haul distance is 50 m, with…

A: Given data- Length of free haul distance (Lf) = 50 m Limit of economical haul (Le) = 450 m The cost…

Q: A 4-yard dragline is being used to excavate a canal in wet. sticky clay. The average swing angle is…

A: Step 1: 4 yard drag lines Swing angle -75 deg Hcut=11 ft Job eff = 44 mins per hour BCY=1.578

Q: o0.2. Estimate the output per hour in bank volume of a power shovel capacity excavating a foundation…

A: Given, data, Bulk volume = 150m³/hr Angle of swing = 150° Factor = 0.88 Swell factor =1.3

Q: An excavation of 25,750 m3 (bm) is to be made for the foundation excavation of a building in 5 weeks…

A: Hauling is the movement of material by mobile units such as road vehicles and rail locomotives. Road…

Q: An excavation for a square footing is 3.5m deep. The bottom of the excavation is 4 square meters. If…

A: Depth of footing = 3.5 m Area for the bottom of excavation(A1) = 4 m2 Side slope for edges of…

Q: If the free haul area is between 4+30 and 14+30, what is the average haul distance (ft) for the net…

A: Given data- Free Haul Area between 4+30 and 14+30 Volume section between 2+60 and 3+00 To Find-…

Q: Estimate the actual bucket load in bank measure for a shovel bucket whose capacity is 3.0 m3. The…

A: The given data is: The bucket capacity=3 m3 Soil bucket fill factor=0.8 Load factor=0.7

Q: Q1: In construction of a highway section, the earthwork information is available as shown in the…

A: Given - Free haul distance = 500m Swelling factor = 20% Overhaul price = $200/m3 To find -Mass…

Q: what is the cost of borrow per cu.m.

A: given- an earthwork computation , the results shown that the length of free haul distance is 50 m,…

Q: FUNDAMENTALS OF SURVEYING 1) What is called the unwanted excavated materials for disposal out of…

A: 1. Waste is the unwanted excavated material which comes when earth is dug out for construction…

Q: (c) Giver the end area of cut and fill of soil as in Table Q4(c). If the material bulks after…

A: Data Given: Bulks after excavation = 10% Shrink = 12% Chainage distance = 100m Asked: Draw Mass…

Q: Describe about the Hydraulic transportation method.

A: Hydraulic transportation is a process by which solid materials are moved by a stream of water.

Q: Q.3/A Crawler hoe having a three Cyd bucket and whose cost per hour, including the wage to an…

Q: Estimate the hourly production in bank measures of a hydraulic shovel loading sand and gravel into…

A: Answer We are given Sand and gravel load Front dump bucket Heaped bucket capacity = 5.2 LCM Average…

Q: An excavation of 25,750 m3 (bm) is to be made for the foundation excavation of a building in 5 weeks…

Q: Determine the total toque for 4 cm square shaft using finite element formulation

A: In physics and mechanics, torque is the rotational equivalent of linear force. It is also referred…

Q: Compute for the volume of excavation using end area method

A: For the station 7+460 - Area - A1 = 12×4.14 - 3.5×.6 + 12×1.92 + .6×3.5 + 12×1.92 + 1.52×3.5 +…

Q: n a certain portion of a road construction, the following data were taken; Cost of haul = P30 per…

A: GIVEN: Cost of haul = 30 per cum Cost of borrow = 360 cum

Q: Required: 1. What is the stationing of the end of excavation? 2. Find the volume of fill by end area…

Q: In construction of a highway section, the earthwork information is available as shown in the able…

A: tabulate the given values and find the Equivalent Fill and cumulative values draw the mass haul…

Q: Given the following end areas for cut and fill, complete the earthwork calculation using a shrinkage…

Q: A mass haul diagram shows a free-haul distance of 50 m, cost of excavation of Php 6.00/m³ and a…

A: Solution: Given: Free haul distance = 50 m Cost of excavation = 6/m3 Price of over haul = 0.10/m3

Q: Determine the balanced hauls and indicate the direction of haul for the mass diagram showR below.…

A: Given data- Mr =41400 KN/m26.0×103 Psisubbase Mr =93,150 KN/m2 13.5×103 Psi…

Q: A cantilever sheet pile wall is required to support a temporary excavation, as shown in the…

A: Solution

Question

Give me right solution according to the question.. Urgent please

Table Q4(c): Cut and fill areas
Chainage
Cut and Fill area (m³)
-26
1
52.28
23.58
3
3.73
4
-8.4
5
-63.8
6.
-33.34

(c) Given the end area of cut and fill of soil as in Table Q4(c). If the material bulks
after excavation about 10% and shrink 12%. Given, distance between chainage is
100 m. Draw the mass haul diagram and estimate how much excess cut or fill is
required.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Interpretation of Data

VIEW

Step 2 Calculations for cut and fill volume

VIEW

Step 3 Balance

VIEW

Step 4 Rearranging Table

VIEW

Step 5 Calculations for Equivalent cut and fill volume,

VIEW

Step 6 Calculations for Cumulative Volume,

VIEW

Step 7 Calculations for mass Haul diagram

VIEW

Step by step

Solved in 7 steps with 14 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

In an earthwork computation , the results shown that the length of free haul distance is 50 m, with a limit of economical haul of 450 m. If the cost of haul is estimated to be P40 per cu.m. per meter station, what is the cost of borrow per cu.m.
In construction of a highway section, the earthwork information is available as shown in the table below. The free-haul distance is 500m and the swelling factor is 20%. Draw the mass haul diagram between station 3 + 00 and station 9 + 00 and determine the extra compensation that must be paid to the contractor when the overhaul price is $200/m3 station.
From the given earthworks data shown, determine the total cost of earthworks if unit cost of haul is P 500 per on, unit cost of borrow is P 3,500 per cubic meter, and unit cost of excavation is P 1,000 per cubic meter. Free haul dist. mated to be 400 m. Assume shrinkage of 20 %.
(c) Giver the end area of cut and fill of soil as in Table Q4(c). If the material bulks after excavation about 10% and shrink 12%. Given, distance between chainage is 100 m. Draw the mass haul diagram and estimate how much excess cut or fill is required.
From the given earthworks data shown, determine the total cost of earthworks if unit cost of haul is P 500 per meter station, unit cost of borrow is P 3,500 per cubic meter, and unit cost of excavation is P 1,000 per cubic meter. Free haul distance is estimated to be 400 m. Assume shrinkage to be 20%.
Briefly discuss the advantages of preloading methods?
FUNDAMENTALS OF SURVEYING 1) What is called the unwanted excavated materials for disposal out of the R.O.W?2) It is a factor to be multiplied to excavation volume in order to reduce it.3) It is a factor to be multiplied to excavation volume in order to increaseit.
1.Find the volume of excavation by end area method 2. Compute the volume of fill by end area method
What should be the volume of the pit that remains in theborrow area after all the material required for the fill hasbeen removed?
Q#2 During excavation processes as a civil engineer what types of precautions should be taken and what are its types .
A limestone mine has the following equipment at its primary production face: Excavator: a 15 yd3 (11.5 m3) front-end loader with 40 sec cycle time Trucks: five 100 ton (90 tonne) trucks Material: average blasted rock with medium-hard digging conditions Working conditions: average Haulage cycle time: 20.0 min (a) What is the sustained production rate of the system in tons/hr, assuming 60 min of production per hour'? (b) Which equipment (loader or trucks) governs? (c) What improvements would you recommend to increase mine production without changing equipment?
A new road segment is to be constructed to connect Barangay A to the Central Municipality B. The road to be constructed requires for an excavation all throughout its length of 1.2 km. The end areas of the to-be-excavated route are 6.34 sq. m and 12.59 sq. m and the estimated area in the middle was 9.97 sq. m. Estimate the volume of excavation needed in cubic meters.