(c). The magnitude of stresses have been applied on soil element where Normal vertical stress is120 KN/m2 , Normal horizontal stress is 300 KN/ m², shear stress is 40 KN/m² and Angle ofinternal friction is 20°. Find the Principle stress and Normal and Shear stress on plan AB, figure 1.OyВitOxOxAOyFig .1Solution:1. 01.. . 2. 03.. .3. On.. .4. Tn..

Normal stresses are given and we have to find the stresses on the inclined plane given in question…

(c). The magnitude of stresses have been applied on soil element where Normal vertical stress is 120 KN/m? , Normal horizontal stress is 300 KN/ m?, shear stress is 40 KN/m? and Angle of internal friction is 20°. Find the Principle stress and Normal and Shear stress on plan AB, figure 1. Oy B Ox Ox A Oy Fig .1

(c). The magnitude of stresses have been applied on soil element where Normal vertical stress is 120 KN/m? , Normal horizontal stress is 300 KN/ m?, shear stress is 40 KN/m? and Angle of internal friction is 20°. Find the Principle stress and Normal and Shear stress on plan AB, figure 1. Oy B Ox Ox A Oy Fig .1

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter9: In Situ Stresses

Section: Chapter Questions

Problem 9.4P

See similar textbooks

Similar questions

A granular soil is subjected to a minor principal stress of 200 kN/m2. If the angle of internal friction is 30°. What is the shear stress on the plane of failure? a.173.2 b.300 c.200 d.224.2
The soil stress state is shown in the figure, σx = 10 kN/m2, σy = 50 kN/m2, τxy = -10 kN/m2:(1) Please use Mohr circle to draw the soil stress state(2) Calculate the maximum principal stress σ1 and the minimum principal stress σ3(3) Please find the (pole) position(4) What is the angle of intersection between the maximum principal stress surface and the horizontal plane?
The soil in a deposit underlying an area where a level ground surface exists has a unit weight of 22 kN/m3. Determine the principal stresses o1 and oz at a depth of 5 m below the soil surface if the lateral pressure is 0.50 of the vertical pressure. Adjust your answer to ZERO decimal places. 01 = kN/m2, 03 = kN/m2
A soil profi le consists of a clay layer underlain by a sandlayer, as shown in Figure P7.17. If a tube is inserted intothe bottom sand layer and the water level rises to 1 mabove the ground surface, determine the vertical effective stresses and porewater pressures at A, B, and C. IfKo is 0.5, determine the lateral effective and lateral totalstresses at A, B, and C. What is the value of the porewater pressure at A to cause the vertical effective stressthere to be zero?
A circular area having a radius of 3 m carries a uniformly distributed of 90 kPa is applied to the ground. Compute the total vertical stress in kN/m^2 increment due to this unifrom load if the unit weight of soil is 18.40 kN/m^3 at point 6 m below the edge of the circular area. a. 18.62 b. 137.66 c. 115.17 d. 129.02
An embankment consists of clay fill for which c=25 kPa and angle of internal friction is 260 (from consolidated undrained test with pore pressure measurement) The weight of fill per unit volume is 18.64 kN/m3. Compute the effective stress in kPa at a depth of 20 m. If the pore pressure at this point is shown by a piezometer to be 180 kPa. a. 62.5 b. 372.8 c. 192.8 d. 21.6
A granular soil is subjected to a minor principal stress of 200 kN/m2. If the angle of internal friction is 30°, determine the inclination of the plane of failure with respect to the direction of the major principal stress. Show free body diagram. a.30 b.45 c.60 d.37.5
6. From the given soil profile, the groundwater table is located 2m below the ground level. (See picture below) Compute the horizontal effective stress at point A. (Answer: 53.36 kPa) Compute the lateral effective stress at point A if the lateral earth pressure coefficient at rest is K0=0.50. (Answer: 26.68 kPa) Compute the lateral total stress at point A. (Answer: 56.11 m)
An embankment consists of clay fill for which c=25 kPa and angle of internal friction is 260 9from consolidated undrained test with pore pressure measurement) The weight of fill per unit volume is 18.64 kN/m3. Compute the stress in kPa at depth of 20 m. Show free body diagram a.21.6 b.372.8 c.192.8 d.62.5
3. The following convergence measurements (U) have been made in a 4.6-m-diameter circular vertical shaft in good quality granitic rock mass (Em = 40 GPa, ν = 0.2): θ (deg) U (mm) 0 2.25 45 2.39 90 1.50 135 1.00 a) Derive the equations that relate convergence to in situ stress. b) The angle θ is measured (clockwise) with respect to the x-axis, which is oriented 30 degrees clockwise from True North. What is the orientation of the maximum principal stress with respect to True North?
Redo Problem 6.12 using Figure 6.15. 6.12 Refer to Problem 6.1. Using Eqs. (6.3) and (6.29), estimate the average stress increase (av) below the center of the loaded area between depths of 3 m and 6 m. 6.1 A flexible circular area is subjected to a uniformly distributed load of 150 kN/m2 (Figure 6.2). The diameter of the load area is 2 m. Determine the stress increase in a soil mass at points located 3 m below the loaded area at r = 0, 0.4 m, 0.8 m, and 1 m. Use Boussinesqs solution. Figure 6.2 Increase in pressure under a uniformly loaded flexible circular area
Refer to Problem 6.1. Using Eqs. (6.3) and (6.29), estimate the average stress increase (Δσav) below the center of the loaded area between depths of 3 m and 6 m. 6.1 A flexible circular area is subjected to a uniformly distributed load of 150kN/m2 (Figure 6.2). The diameter of the load area is 2 m. Determine the stress increase in a soil mass at points located 3 m below the loaded area at r = 0. 0.4 m, 0.8 m, and 1 m. Use Boussinesq’s solution. Figure 6.2 Increase in pressure under a uniformly loaded flexible circular area