C100 x 8.Angle 100 x 75 x 6The composite shape shown below was manufactured by welding a structural steel angleshape to a standard C-channel.a) Delermine the location of be horzontal Centroidal axis ol the composile shape,b) Compute the arca moment of mertia with respect to the honzontal cetroidal axis

Answered: Image /qna-images/answer/00369698-3445-4990-a2d2-e6adfaffb47c.jpg

C100 x 8 Angle 100 x 75 x 6 The composite shape shown below was manufactured by welding a structural steel angle shape to a standard C-channel. a) Determine the location of Ibe horizontal centroidal axis ol the composile shape, b) Compute the arca moment of mertia with respect to the honzontal centroidal axis

C100 x 8 Angle 100 x 75 x 6 The composite shape shown below was manufactured by welding a structural steel angle shape to a standard C-channel. a) Determine the location of Ibe horizontal centroidal axis ol the composile shape, b) Compute the arca moment of mertia with respect to the honzontal centroidal axis

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.7.1P

See similar textbooks

Similar questions

A concrete beam has a width of 400 mm. It is reinforced at the bottom fiber with 4 – 28 mm deformed steel bars. Use f’c= (49) MPa and fy = (362) MPa. Determine the effective depth of the beam such that the design falls the boundary (a) between compression and transition zones as well as (b) between transition and tension zones.
Locate centroid for the following composite section:
Determine the centroid of the composite steel shape for the given axis system. Channel profile properties are available in Appendix A1 in textbook. The Appendix is posted on Canvas under Course Materials.
A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. The concrete cover to bar centroid is 80 mm and at the bottom is 70 mm. use concrete strength f'= 21 MPa and steel yield strength fy=415 MPa for all bars. 1. Determine the tensile steel ratio when the beam is in positive bending. a. 0.01567 b. 0.01283 c. 0.01169 d. 0.01923 2. Determine the nominal moment capacity in kN-m of the beam in positive bending. a. 188.30 b.167.70 c.218.96 d.193.68 3. Determine the tensile steel ratio when the beam is in negative bending. a. 0.00406 b. 0.00475 c.0.00383 d. 0.00508 please provide a complete solution so I can understand. Very much appreciated to solve it early !!
For a composite section attached, derive the equation for Y-bar assuming that the PNA is located in the flange of the steel beam. Hint: Balance the resultant forces through the section. Recall that Y-bar is the distance from the top of the steel flange to the PNA for any location with the PNA below the top of the steel flange.
3 A concrete floor slab 100 mm thick is cast monolithic with concrete beams 2.0 m on centers. The beams have a span of 4.0 m, web width of 250 mm and overall depth of 500 mm. The tensile reinforcement consists of 6-∅20 mm bars in two rows with 25 mm vertical clear spacing. Use material strengths f’c = 21 MPa and fy = 415 MPa. Calculate the following considering a T-geometry: Effective flange width of an interior beam in mm = ? Depth of uniform stress block at ultimate stage in mm to the nearest whole number = ?? Tensile steel strain compatible with concrete strain of 0.003 in 3 decimal places = ?
Show the complete FBD and complete solution. Given that centroid of the plane regions is at c find the radius R. use the method of composite areas
the load is 150kN at the center of the beam and the dimension of the beam is 6''x6''x24''. compute for modulus of rupture of beam.
Locate the centroid y bar of the composite area, then determine the moment of inertia of this area about the centroidal xannouncement: pulg = inch
a. Locate the centroid of the composite area. Choose your own reference axes. b. Draw the location of the centroidal x and y axes. c. Compute the moment of inertia about centroidal x and y axes. (Please include the specific formula.)
A reinforced concrete rectangular beam with 250 mm in width has an effective depth of 500 mm. It is reinforced only at the bottom with 5-28mm Φ bar. The reinforcing steel strength (Fs = 140 MPa) and a compressive strength of concrete is 28 MPa. Use alternate working stress design method. Modular ratio n = 9. 1. Which of the following most near ly gives the location of the neutral axis from the top most fiber of the beam. a. 256 mm b. 236 mm c. 226 mm d. 240 mm 2. If it is subjected to a total actual service moment of 100 kN-m, find the actual maximum concrete stress (in MPa) a. 7.93 b. 8.84 c. 6.84 d. 5.93 3. If it is subjected to a total actual service moment of 100 kN-m, find the actual maximum steel stress (in MPa) a. 73.63 b. 77.34 c. 66.84 d. 56.85
The composite section shown is made up of Channel and Wide Flange Steel section. Determine the properties of composite section. Channel (C 15 x 40) Wide Flange (W 18 x 158)