Calculate :mass of the chain link and surface area of chain linl 3Determine the mass of the chain link shown in Figure 4. The link is made from a 6-mm-radius steel rod of density 7850 kg/m,where R= 10 mm and L = 30 cm.RRFigure 4: A chain link of length L and radius R at the semi-circular ends.Answer:Find the surface area of the the chain link in question 10.Answer:

Answered: Image /qna-images/answer/b31a0cf5-6a66-45b3-b321-20ea689130ad.jpg

Answered: Calculate : mass of the chain link and…

Engineering

Mechanical Engineering

Calculate : mass of the chain link and surface area of chain linl

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter9: Moments And Products Of Inertia Of Areas

Section: Chapter Questions

Problem 9.13P: Figure (a) shows the cross section of a column that uses a structural shape known as W867...

See similar textbooks

Related questions

Q: Compute the potential energy stored in raising object to height of 6.55 m having mass 10 kg

Q: Find the load carried by tower crane if G= 200N

Q: reading shown? For the 6 psi. The fluid in both pines A and B is water

A: we will use the equation of inclined tube manometer PA+γ1h1γ2I2 sinθ-γ3h3 =PB

Q: Compute the pressure produced in the oil in a closed cyl- inder by a piston exerting a force of 2500…

Q: Q1: Gate AB which is shown in figure (1) is (15m) long and (10m) wide and hinged at B with a stop at…

Q: A cargo truck with a weight of 289 kN was raised using a hydraulic press. If oil acts on a piston…

A: Correct answer: 1148.62 kPa

Q: Compute the mass of 60 ˚C air inside the rectangular shape system with dimensions 2m X 3m X 1m. The…

Q: What are the allowable values of the cross-sectional height

Q: 1.calculate the volume of displace water (m3) of sample 1-3 2. calculate Fb(N) of sample 1-3 3.…

Q: Qq; As shown in figure belaw, the plug weighs 0.3 KN/u. spherical Calculate (D) for ? buoy valve to…

A: Given data: The net pressure on the plug can be determined as,

Q: Problem 4- Fluids and Heat a) A distant planet has an average mass density identical to that of…

A: Gravitational acceleration Gravitational acceleration on any planet is given by, g =Gmr2 Where, G =…

Q: piston of 12 mm diameter and a Tge piston of 60 mm diameter. Calculate the force needed.on the nall…

A: Dia of small = 12 mm Dia of larger = 60 mm Load to be raised = 8 kN Force required = F Applying…

Q: Q) Write introduction and conclusion for Lift Mechanism

A: Given:

Q: Calculate the formula mass for compound. Ca(NO3)2

A: Mass in gram per mole for Ca = 40 Mass in gram per mole for N = 14 Mass in gram per mole for O = 16

Q: Give an example of Lifting of a large weight by a small force by the application of Pascal’s law. A…

A: According to Pascal law pressure on the enclosed fluid is transmitted throughout the fluid with…

Q: need of Fair is su s 310 m

Q: Calculate the blade length of a wind turbine rotor v

A: Given: Power (P)=4 MW=4×106 Wwind speed v=48 km/hr=13.33 m/sAir densityρ=1.23 kg/m3Generator…

Q: Compute the height to be raised of box to gain potential energy of 544 J having mass of box 23 kg

A: The height to be raised of box to gain potential energy of 544 J having mass of box 23 kg is h = 2.4…

Q: cylinder bore is 67 mm and the piston stroke is 57 mm. Compute (a) the clearance volumetric…

A: Given: Six cylinder refrigerant 22 compressor 29 r/s, 96.4 kW refrigerant capacity 28.9 kW power…

Q: An open cylindrical vessel 1.2 m in diameter and 2.1 m high is 2/3 full of water. Compute the amount…

Q: If you put a uniform block at the edge of a table, the center of the block must be over the table…

A: a) The center of gravity of top block can be as far out as the edge of the lower block. The center…

Q: chain wit RS=102.3m

Q: Convert 4.58 x 10^3 cm^3 to gal.

A: Given: The volume is V=4.58×103 cm3. The unit conversion factor to convert Centimeter cube into…

Q: 65.A cube of wood (s.g. 0.60) has 9-in sides. Compute the magnitude direction of the force required…

A: Given Specific gravity = 0.9 Side = 9 in = 0.75 ft…

Q: 4. If the compression ratio is 17:1 and the piston displacement is 10 cc. Compute for piston…

A: Dear student, we are suppose to solve only one question. Please post other question as a separate…

Q: Determine the most efficient value of θ for the V-shapedchannel of Fig.

A: Let's first determine the area of the V-shaped channel, The area of the V-shaped channel is,…

Q: Calculate the height of a column of water equivalent to atmospheric pressure of 1.02bar if the water…

Q: Given: A bar ( from point A to B )of 4 meters in length and weighting 20 kilos where its center of…

A: given; mass (m1)=20kgmass (m2)=10kgcenter of gravity for 20kg mass ,(x1)=2m from point Acenter of…

Q: Diagram of the problem, necessary formulas, clearance and numerical solution It is planned to lift…

Q: n. Calculate the force exerted by the seat

A: Given: V=670km/h R=1270m m=99kg To find NA NB

Q: Calculate the forces on the rod by using the method of analytics

A: Data given-

Q: ng the weight of the beam, comput in Fig

Q: 150 Ib/ft 100 lb

A: Consider the member AB and drawing FBD as shown below, Balancing vertical…

Q: of 300 mm running at a speed of 2950 rev/min delivering 45 similar spare pump running at a speed of…

Q: A freshly cut log floats with one fourth of its volume protruding above the water surface. The…

Q: collar at A necessary to hold the 250-lb sign in equiſibrium. The center of gravity for the sign is…

A: Answer: Tension in cables : BC = 225 lb and DE = 150 lb Reaction forces acting at A : Ax = 25 lb ,…

Q: of span 100 m and

Q: construct the free-body diagram of gate

A: The gate mass is 84 kg and its center of mass located at G the reaction force at point A is in…

Q: This butterfly valve that have 3 m-diameter is used to control the flow in a 3 m-diameter outlet…

A: Given details: d=3 mh= 10m formula used: F=ρgAh

Q: Calculate the reaction MAz

A: In the given force system, the 150 N force did not result in any moment about the z-axis as this…

Q: Qqs As shown in figure belaw, the plug weighs o.3 KN/u. spherical Calculate (D) for ? buoy valve to…

Q: b. Draw velocity triangles at inlet and outlet of the axial flow compressor blade for degree of…

Q: A rectangular pontoon has a width of 6m, length of 12m and draughts of 1.5 min fresh water.…

A: Given data width (w) = 6 m length (l) = 12 m draught (x) = 1.5 m in fresh water To determine (a)…

Q: Calculate the resultant force on the screw eye. Note the upper part of the rope is horizantal.

Q: Problem -1 A tank containing of 50 Kg of water saturated liquid at constant temperature is 90°C.…

A: Note:As per our guidelines we are supposed to answer only one question. Kindly repost other…

Q: The motor of the pimp consumes 1.05 hp of electricity. The pump increases the pressure of water from…

Q: Daive equabon for height Rof Patee Centre Method. Gvene usuig Instantenous

Q: work done in extending the spring is? From Following Graph.

Q: Q1/ For the hydraulic jack shown in Figure. Assume the specific weight of the liquid in the jack is…

A: The pressure generated in the smaller diameter cylinder due to the applied force can be determined…

Concept explainers

Center of Gravity and Centroid

The term center of gravity indicates the position or location of a point about which the whole weight of a body or system is supposed to be concentrated, which means the whole weight of the body or system works through this point. It is closely related to mass distribution. For all positions of the body, the center of gravity would be a single point.

Question

Calculate :

mass of the chain link and surface area of chain linl

3
Determine the mass of the chain link shown in Figure 4. The link is made from a 6-mm-radius steel rod of density 7850 kg/m,
where R= 10 mm and L = 30 cm.
R
R
Figure 4: A chain link of length L and radius R at the semi-circular ends.
Answer:
Find the surface area of the the chain link in question 10.
Answer:

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 540-N uniform rectangular sign 4.00 m wide and 3.00 m high is suspended from a horizontal, 6.00-m-long, uniform, 140-N rod as indicated in the figure below. The left end of the rod is supported by a hinge and the right end is supported by a thin cable making a 30.0° angle with the vertical. (Assume the cable is connected to the very end of the 6.00-m-long rod, and that there are 2.00 m separating the wall from the sign.) (a) Find the (magnitude of the) tension T in the cable.N(b) Find the horizontal and vertical components of the force exerted on the left end of the rod by the hinge. (Take up and to the right to be the positive directions. Indicate the direction with the sign of your answer.) horizontal component _____N vertical component _____N
Find the center of mass of the structure given in the figure below. Assume a uniform thickness of 20 cm, and a uniform density of 1 g/cm3.
A 15,000 N crane pivots around a friction-free axle at its base and is supported by a cable making a 25∘ angle with the crane (Figure 1). The crane is 16 m long and is not uniform, its center of gravity being 7.0 m from the axle as measured along the crane. The cable is attached 3.0 m from the upper end of the crane. 1. When the crane is raised to 55∘ above the horizontal holding an 11,000 N pallet of bricks by a 2.2 m very light cord, find the tension in the cable. 2. Find the horizontal component of the force that the axle exerts on the crane.
A 27 m vertical column of fluid (density 1878 kg.m3) is located where g= 9.65 m/sec2. Find the pressure at the base of the column.Ans. 489.313 kPa Please give me the solution.
A cube with edges of length L = 0.23 m and density ρc = 3.4×103 kg/m3 is totally submerged in water, with a density of ρw = 1.00×103 kg/m3, and oil, with a density of ρo = 0.82×103 kg/m3, as shown in the figure. The cube is submerged in the water to a depth of d = 0.065 m, while the rest of the cube is in oil. The cube is suspended by a taut string and is in static equilibrium. a) Calculate the magnitude of the buoyant force, in newtons. b) Enter an expression for the tension in the string, in terms of the defined quantities and g.
A vertical cylinder gasoline storage tank is 30m in diameter and is filled to a depth of 15m with gasoline of mass density 740 kg/m³. if the shell plating has an allowable stress of 100 MPa, calculate the required wall thickness at the bottom of the tank.
Determine the centroid of the surface shown in the figure below in two ways: The. Using a vertical differential element of dx thickness; B. By double integration The chart should contain all the information necessary to understand the issue
the timber shown is 30cm square and has a specific gravity of 0.50. A man weighing 70kg standing at a point 60cm from one end causes that end to be just submerged. How long is the timber? Answer: L=5m
A cylinder weighing 445 N and having a diameter of 1 m floats in salt water (sp.gr. 1.03) vertically. It has an anchor tied to the cylinder, where the anchor rest at the bottom of the earth. The anchor weigh 23540 N/m3 and has a volume of 0.280 m3. What height “h” above the water surface will be required to lift the anchor off the bottom of the water when a high tide occur? The part of the cylinder is submerged 0.30 m below the salt water.
A piece of steel wire, which is 3 m long, and of 1 mm diameter hangs vertically from the ceiling. A 5 kg mass, made from iron, (density = 7,9 x 103 kg.m-3 ) is attached to the free end. Find the tension in the wire when the mass is completely submerged in the water. (Density of water = 1 000 kg.m-3 )
Use stiffness influence coefficients to derive the stiffness matrix for A massless rod and other attachments shown in figure below. the center of gravity of 2m mass locate 1/3 of length from right hand end. N 15 3 15 2 ® m 3 2mI
A thin-walled hollow sphere 3.8 m in diameter holds helium gas at 1767 kPa. Determine the minimum wall thickness of the sphere in mm if its allowable stress is 84.8 MPa.