Calculate the capillary effect in mm in a glass tube of 4mm diameter, when immersed in (1)water, (2)mercury. The temperature of the liquid is 25°C and the values of surface tensions of water and mercury at 25°C in contact with air is 0.0735 and 0.59N/m respectively. The angle of contact for water is 0° and 130° for mercury . Take the density of water 1000 kg/m³ , specific gravity of mercury is 13.6.

Calculate the capillary effect in mm in a glass tube of 4mm diameter, when immersed in (1)water, (2)mercury. The temperature of the liquid is 25°C and the values of surface tensions of water and mercury at 25°C in contact with air is 0.0735 and 0.59N/m respectively. The angle of contact for water is 0° and 130° for mercury . Take the density of water 1000 kg/m³ , specific gravity of mercury is 13.6.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter9: Heat Transfer With Phase Change

Section: Chapter Questions

Problem 9.26P

See similar textbooks

Similar questions

Calculate the capillary effect in mm in a glass tube of 6 mm diameter when immersed in (i) water, and (ii) mercury, both liquids being at 20°C. Assume σ to be 73 × 10−3 N/m for water and 0.51 N/m for mercury. The contact angles for water and mercury are zero and 130°, respectively.
A 0.10-mm-diameter glass tube is inserted into water at 100°C in a tub to observe capillary rise phenomenon. Determine the capillary rise of water in the tube. (a) What would happen if water is replaced with gasoline in tube? (b) Can you calculate the capillary rise if the diameter of tube at one end is 0.3mm and on the other end it is 0.10mm
A 0.10-mm-diameter glass tube is inserted into water at 100°C in a tub to observe capillary rise phenomenon. Determine the capillary rise of water in the tube. (a) What would happen if the water is cooled down to 20°C? (b) What would happen if 0.10mm tube replaced with 0.3mm tube?
Calculate the magnitude of capillary effect in millimeters in a glass tube of 7 mm diameter when immersed in mercury. The temperature of the liquid is 25oC and the and the values of surface tension of mercury at 25oC is 0.51 N/m. The angle of contact for mercury is 130o
Calculate the capillary effect in mm in a glass tube of 4mm diameter, when immersed in (1)water, (2)mercury. The temperature of the liquid is 25ᵒC and the values of surface tensions of water and mercury at 25⁰C in contact with air is 0.0735 and 0.59N/m respectively. The angle of contact for water is 0ᵒ and 130ᵒ for mercury . Take the density of water 1000 kg/m3 , specific gravity of mercury is 13.6. The capillary effect of water in mm is equal to= The capillary effect of mercury in mm is equal to=
Compare the capillary effect of immersion in (i) water and (ii) mercury of a glass tube of 6 mm internal diameter. The surface tension values are 0.072500 N/m and 0.60 N/m for water and mercury. The angle of contact for water is zero degree. The angle of contact for mercury is 130°
Consider a thin-walled, ﬁ xed-volume container of volume V that holds an ideal gas at constant temperature T. It can be shown by dimensional analysis that the number of particles striking the walls of the container per unit area per unit time is given by nv-/4, where as usual n is the particle number density. The container has a small hole of area A in its surface through which the gas can leak slowly. Assume that A is much less than the surface area of the container. (a) Assuming that the pressure inside the container is much greater than the outside pressure (so that no gas will leak from the outside back in), estimate the time it will take for the pressure inside to drop to half the initial value. Your answer should contain A, V, and the mean molecular speed v-. (b) Obtain a numerical result for a spherical container with a diameter of 40 cm containing air at 293 K, if there is a circular hole of diameter 1.0 mm in the surface.
The hot water coming out of a hydrothermal vent is sometimes called vent fluid. Why would you and I find these vent fluids to be an unpleasant thing to be exposed to? a They are some of the coldest fluids on Earth, being much colder than the normal freezing point of water. b They can be up to 400 degrees Celsius, and contain dissolved compounds like hydrogen sulfide, carbon dioxide, and methane. c The vent fluids are actually an exotic type of magma, made of silicate minerals. d They are actually ultra-pure water, with nothing at all dissolved in them; so pure that even simple cells will die due to the lack of nutrients in the fluids.
The capillary effect in a glass tube of 3.7 mm diameter, when immersed in (1) water and (2) mercury are 8.2 mm and -3.6 mm respectively. Calculate the value of surface tension in contact with air for water and mercury in N/m. Take, the contact angle for water =00 and mercury =1300.
0.04 m3 of gas at a pressure of 1482 KN/m2 is expanded isothermally unit volume is 0.09 m3, calculate the work done during the expansion.
a hemispherical liquid drop formed under a solid surface is just about to separate and fall . determine the diameter of this drop just before separation from the solid surface. take y=9790N/m3 and a=0.073N/m
Nutrients dissolved in water are carried to upper parts of plants by tiny tubes partly because of the capillary effect. Determine how high the water solution will rise in a tree in a 0.0026-mm-diameter tube as a result of the capillary effect. Treat the solution as water at 20°C with a contact angle of 15°. The density of water is 1000 kg/m3.