Need help with c and d (a) If the time domain expression for the source is io(b) If the impedances are z, = j10000 N and z,20.04 cos(1250t) amps, find the phasor expression I,5000 – j10000 N, findthe equivalent impedance seen by the currentZeqssource(c) Calculate the complex power S, supplied by the current source(d) Calculate the power factor of the current sourceZ1Z2

Answered: ) Calculate the complex power S,…

Engineering

Electrical Engineering

) Calculate the complex power S, supplied by the current source ) Calculate the power factor of the current source

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For the frequency-domain circuit , calculate: 1. a) the rms magnitude of Vo;2. b) the average power dissipated in the 9 Ω resistor;3. c) the percentage of the average power generated by the idealvoltage source that is delivered to the 9 Ω load resistor.
characteristic impedance z0 = 50 ohms is a short-circuited coaxial (coaxial) cable with a length d = 0.3λ component is wanted to be made. Use Its frequency is f = 8 GHz. (a) Identify the component. (b) Find the impedance value of the component. (c) Find the parameter value of the component. lesson:electrical and electronical engineering
five infinite-impedance volunteers,calibrated to read rms values,are connected as shown below. let R= 200, L=0.400H,C=6.0 Mf, and V=30.0 v. what's the reading of the voltmeter's V1,V2,V3,V4 and V5 if W= 200 rad/s
S.2) The serial impedance of the 300 km power transmission line is 23 + j75 ohm / phase and the shunt acceptance is j500 microS / phase. A power of 50 MW with a power factor of 0.88 under 220 kV interphase voltage from the end of the power transmission line being shot. Using these data of the energy transmission line, a) Characteristic impedance of the energy transmission line, b) Natural apparent power of the energy transmission line according to the 220 kV interphase operating voltage, c) The values of the line parameters A, B, C and D of the transmission line using hyperbolic functions, d) Calculate the maximum power that the power transmission line can transmit.
6.23 Find period, frequency, phase angle in degrees, and maximum, minimum, average, and effective values of vðtÞ ¼ 2 þ 6 cosð10t þ =6Þ. Ans: T ¼ 0:2 s; f ¼ 5 Hz; phase ¼ 308; Vmax ¼ 8; Vmin ¼ 4; Vavg ¼ 2; Veff ¼ ffiffiffiffiffi 22
A SERIES RC CIRCUIT TAKES A CURRENT WHOSE EQUATION Is 2 sin (754t+40) AMPERE. WHEN CONNECTED TO A SOURCE OF EMF HAVING THE EQUATION e = 340sin 754 VOLTS. CALCULATE, (A) THE VALUE OF Z, R, AND XC, (B) CAPACITANCE, AND (C) AVERAGE POWER.
The values of the parameters in the circuit shown are L1=8 mH; L2=2 mH; k=0.75; Rg=1 Ω; and RL=7 Ω. Ifvg=542 cos 1000t V, find 1. a) the rms magnitude of vo;2. b) the average power delivered to RL;3. c) the percentage of the average power generated by the idealvoltage source that is delivered to RL.
The feeder is to be used with an antenna for which an inductive reactance is measured as j60 Ohms at 1.7 MHz. The resistive part of the antenna’s impedance is measured as 80 Ohms. Using the online impedance matching calculator, design a suitable impedance-matching network for each of the two cables if the coaxial cable has a characteristic impedance of 75 Ohms and the twin lead cable has a characteristic impedance of 300 Ohms, so that the inductance is in the longitudinal branch, while the capacitor is in the transversal branch of the impedance matching network. Do not round the resulting values.
A series circuit of RLC with following parameters, R=15 ohm, L=20 m H & C=100 micro Farad. VT=169.7 sin (337t-30) Volt. Find the following: Zt, , It, Voltage across each element, Power factor, apparent power, real or average power and reactive power and the total phasor diagram and power phasor diagram
A HV transmission line having receiving end load is 300MVA, 50 Hz line from poin A to point B. Resistance 0.13 ohm/KM , for 160 KM Inductance XL= 0.4 ohm per kilometer Parallel admittance j318 × 10-6 Power Factor 0.8770, 0.8477 lagging, unity and 0.8770, 0.8477 leading Assume desired voltage at the receiving end of the transmission line is not less than 380kV., if the line is supplying rated voltage and apparent power at various power factors given Estimate : a. Sending end voltages b. Voltage regulation c. Efficiency of the transmission line d. Give a technical explanations on the results obtained
a) You have been employed as an electrical engineer by a power transmission company to design a short transmission line to supply power to a light-industrial load consumer with power system specification as follows, a 3-ph, 60Hz overhead short transmission line with a line-to-line voltage of 23KV at the load end, line impedance of 2.48 ±j6.57Ω/phase, the industry has a cumulative consumption of 9MW with a power factor of 0.85 of lagging as a result of several induction motor on its production lines.As part of the regulations for connections to the grid, you are to provide justifications and values to the Energy Commission of Ghana.(i) What would be value of the voltage between the live conductor and the neutral, between live and live voltages at the industrial premises of the factory?(ii) What load angle would expect the factory to be operating at?
A 25V, 2.5kHz supply is connected to a network comprising a variable capacitor in parallel with a coil of resistance 250 ohms and inductance 80 mH. Determine, for the condition when the supply current is a minimum the capacitance of the capacitor the dynamic impedance the supply current the upper half-power frequency the value of the circuit impedance at the -3dB frequencies