Calculate the concentration of a solution species that yields a 500 μA peak current response in a cyclic voltammetry experiment with a sweep rate of 50 mV s-1 at a 0.5 cm2 planar electrode and a temperature of 30 °C. Assume the species undergoes a two electron oxidation/reduction and has a diffusion coefficient of 2 x 10-5 cm2 s-1. 2.33 x 10-5 mol cm-2 2.33 x 10-6 mol cm-2 1.33 x 10-5 mol cm-2 1.33 x 10-6 mol cm-2

Calculate the concentration of a solution species that yields a 500 μA peak current response in a cyclic voltammetry experiment with a sweep rate of 50 mV s-1 at a 0.5 cm2 planar electrode and a temperature of 30 °C. Assume the species undergoes a two electron oxidation/reduction and has a diffusion coefficient of 2 x 10-5 cm2 s-1. 2.33 x 10-5 mol cm-2 2.33 x 10-6 mol cm-2 1.33 x 10-5 mol cm-2 1.33 x 10-6 mol cm-2

Fundamentals Of Analytical Chemistry

9th Edition

ISBN:9781285640686

Author:Skoog

Publisher:Skoog

Chapter22: Bulk Electrolysis: Electrogravimetry And Coulometry

Section: Chapter Questions

Problem 22.1QAP

See similar textbooks

Similar questions

Chemistry The exchange current density for the electrode Pt(s) │|H2(g) │|H+(aq) is 0.79mA cm-2 at 25°C. What is the current density in the electrode when its overpotential is 5.0 mV, and what is the anode current through of an electrode with a surface area of 5.0 cm2 Solution: . 0,15 mA cm-2, 0,75 mA
The boundary equivalent conductivity of the 0.1 M electrolyte with a resistance of 0.33 ohms was determined as 320 Scm-2mol-1 and the conductivity ratio was determined as 0.55. According to this information, the electrolyte; a) Equivalent conductivityb) Self conductivityb) Find the cell constant of the electrode used.
A conductivity cell was calibrated using 0.01 M KCl (κ = 1.4087x10-3 S/cm) and the measured resistance was 688 Ω. a. Determine the cell constant (include units). b. Determine the molar conductivity, Λm for a 0.0100 M AgNO3 solution in the same cell with a resistance reading of 777Ω.
The exchange-current density for a Pt|Fe3+,Fe2+ electrode is 2.5 mA cm−2. The standard potential of the electrode is +0.77 V. Derive an expression for the current flowing through an electrode of surface area 1.0 cm2 as a function of the potential applied to the electrode; assume standard conditions.
An unknown cadmium(II) solution was analyzed polarographically by the method of standard additions. A 25.00-mL sample of the unknown solution produced a diffusion current of 1.86 mA. Following addition of a 5.00-mL aliquot of 2.12x10^23 M Cd2+ standard solution to the unknown solution, a diffusion current of 5.27 mA was produced. Calculate the concentration of Cd2+ in the unknown solution.
The resistances of a series of aqueous NaCl solutions, formed by successive dilution of a sample, were measured in a cell with cell constant (the constant C in the relation κ = C/R) equal to 0.2063 cm-1 and the following values were found at 25oC: c/(mol dm−3) 0.00050 0.0010 0.0050 0.010 0.020 0.050 R/W 3314 1669 342.1 174.1 89.08 37.14 Find the molar conductance of NaCl at 25oC at infinite dilution from the graph.
When a certain electrolytic cell was filled with 0.1 M KC1, it has resistance of 85 ohms at 25 °C. When the same cell was filled with an aqueous solution of 0.052 M unknown electrolyte, the resistance was 96 ohms. Calculate the molar conductance of the electrolyte at this concentration.[Specific conductance of 0.1 M KC1 = 1.29 X 10-2ohm-1 cm-1]
The resistances of a series of aqueous NaCI solutions, formed by successive dilution of a sample, were measured in a cell with cell constant (the constant C in the relation κ = C/R) equal to 0.2063 cm-1. The following values were found: c/(mol dm-3) 0.00050 0.0010 0.0050 0.010 0.020 0.050R/Ω 3314 1669 342.1 172.5 89.08 3714(a) Verify that the molar conductivity follows the Kohlrausch law and find the limiting molar conductivity. (b) Determine the coefficient κ, (c) Use the value of κ (which should depend only on the nature, not the identity of the ions) and the information that λ(Na+) = 5.01 mS m2 mol-1 and , λ(I-) = 768 mS m2 mol-1, to predict (i) the molar conductivity, (ii) the conductivity,(iii) the resistance it would show in the cell, of 0.010 mol dm-3 Nal(aq) at 25 °C.
A typical exchange-current density, that for H+ discharge at platinum, is 0.79 mA cm−2 at 25 °C. Use the Butler–Volmer equation to calculate the current density at an electrode when its overpotential is (a) 10 mV, (b) 100 mV, (c) −5.0 V. Take α = 0.5.
5. An infinite flat plate of a solid has a surface potential of 50 mV in an infinite bath of 10-2 molL-1 NaCl(aq) aqueous solution at 298K. Make a plot of the potential, y, the Na+ ion concentration, and the Cl- ion concentration as a function of distance from the interface using (a) the exact equation for potential and (b) the low potential approximation. Comment on the difference between your answer for (a) and (b).
A standard addition method for the voltammetric determination of Pb2+ involved addition of 5.00 mL of 0.800 x 10-3 M Pb2+ to one of two 25.00 mL aliquots of the sample. Supporting electrolyte and water were then added to each aliquot to give a final volume of 50.00 mL. Calculate the molar concentration of Pb2+ based on the following data Diffusion current of sample only = 78.3 uA A Diffusion current of sample with standard addition = 88.7 uA
An ion-selective electrode (ISE) produces voltage output (mV) proportional to solution pH. You have three standard pH solutions (4, 7, and 10). Assuming that pH 7 buffer solution is used together with pH 4 for calibration prior to measuring acidic solutions and together with pH 10 before measuring alkaline solutions, produce a flowchart of the calibration routine for a single pH ISE.