Calculate the convective heat transfer rate per unit length from a 40-cm diameter horizontal pipe whose surface is maintained at 95°C. This pipe is transporting hot water in a steam power plant. The temperature of air around the pipe is 25°C and the air is blowing across the pipe with a velocity of 0.2 mph. 1 mile = 1609 m.

Calculate the convective heat transfer rate per unit length from a 40-cm diameter horizontal pipe whose surface is maintained at 95°C. This pipe is transporting hot water in a steam power plant. The temperature of air around the pipe is 25°C and the air is blowing across the pipe with a velocity of 0.2 mph. 1 mile = 1609 m.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.16P

See similar textbooks

Similar questions

5.7 The average Reynolds number for air passing in turbulent flow over a 2-m-long, flat plate is . Under these conditions, the average Nusselt number was found to be equal to 4150. Determine the average heat transfer coefficient for an oil having thermal properties similar to those in Appendix 2, Table 18, at at the same Reynolds number and flowing over the same plate.
3.10 A spherical shell satellite (3-m-OD, 1.25-cm-thick stainless steel walls) re-enters the atmosphere from outer space. If its original temperature is 38°C, the effective average temperature of the atmosphere is 1093°C, and the effective heat transfer coefficient is , estimate the temperature of the shell after reentry, assuming the time of reentry is 10 min and the interior of the shell is evacuated.
Water at a temperature of 25oC flows parallel over a flat plate with free-stream velocity of 2 m/s. The plate surface temperature is uniform at 86oC. Calculate: a) Thermal boundary layer thickness at x = 8 cm from leading edge; b) Local heat flux on x = 8 cm from leading edge; c) Total heat transfer rate in the area of plate L = 8 cm from the leading edge and width w = 10 cm.
Air at a temperature of 25oC flows parallel over a flat plate with free-stream velocity of 2 m/s. The plate surface temperature is uniform at 86oC. Calculate: a) Thermal boundary layer thickness at x = 8 cm from leading edge; b) Local heat flux on x = 8 cm from leading edge; c) Total heat transfer rate in the area of plate L = 8 cm from the leading edge and width w = 10 cm.
Air at 20oC and 1 atm flows over a flat plate at 35 m/s. The plate is 75 cm long and 100 cm depth and is maintained at 60oC. Calculate (a) velocity boundary layer thickness at the leading edge, (b) thermal boundary layer thickness at the distance of 10 cm from the leading edge, and (c) thermal boundary layer thickness at the trailing edge.
A long aluminum wire of diameter 3 mm is extruded at a temperature of 280°C. The wire is subjected to cross air flow at 20°C at a velocity of 6 m/s. Determine the rate of heat transfer from the wire to the air per meter length when it is first exposed to the air.
Airstream at 1 atm flows, with a velocity of 15 m/s, in parallel over a 3-m-long flat plate where there is an unheated starting length of 1 m. The airstream has a temperature of 20°C and the heated section of the flat plate is maintained at a constant temperature of 80°C. Determine (a) the local convection heat transfer coefficient at the trailing edge and (b) the average convection heat transfer coefficient for the heated section.
Water at 45.0oC flows over a large plate at a velocity of 30.0 cm/s. The plate is 1.0 m long (in the flow direction), and its surface is maintained at a uniform temperature of 5.0oC. Calculate the steady rate of heat transfer per unit width of the plate. Properties The properties of air at 1 atm and the film temperature of (Ts+T∞)/2 = (5+45)/2 = 25°C are: ρ = 996.6 kg/m3, k = 0.610 W/m.oC, μ = 0.854x10-3 kg/m.s, Pr = 5.85
Prove that the thermocouple will underestimate the temperature of airflow by more than 15% but less than 30% in a large air duct if the temperature of the hot air is 1367 K, duct-wall temperature is 533 K, emissivity of the thermocouple is 0.5, and the convection heat-transfer coefficient is 114 W/m2 -K.
Air at 25 ° C blows over the hot steel plate whose surface temperature is maintained at 150 ° C. The plates are 50 cm x 40 cm in dimensions and 3 cm thick. The convection heat transfer coefficient on the upper surface is 30 W / (m² ° C). The thermal conductivity of steel is 45 W / (m ° C). Calculate the hourly heat loss from the plate surface. a. heat loss per hour = AnswerkJ. b. If the reverse side surface temperature is maintained, determine the hourly heat loss occurring = AnswerkJ.
Air at 400C flows with a velocity of 7 m/s over a 5m long and 4m wilde surface of a flat plate whose surface temperature is 800C. Find the rate of heat transfer from the laminar flow region of the surface. (For air at 400C , V = 1.702 × 10-5 , pr = 0.7255, K = 0.02662 w/m . K).
A coated sheet is being dried with hot air blowing in cross flow on the sheet surface. The surface temperature of the sheet is constant at 90°C, while the air velocity and temperature are 0.3 m/s and 110°C, respectively. The length of the sheet subjected to the blowing hot air is 1 m long. Determine the convection heat transfer coefficient and the heat flux added to the sheet surface. Treat the coated sheet as a vertical plate in cross flow.