Calculate the dimensions of the I-section of a connecting rod, stating any assumptions. using the data below: Maximum cylinder pressure = 3.15N/mm² Cylinder bore = 100mm Factor of Safety=6 Crank length 95mm Connecting rod length=380mm Take the constant a=7500.
Q: Just see my handwriting need text form answer not handwriting retype it. Dont mis all retype A to z
A: Given , A solution in handwritten format.To do - rewrite the solution.
Q: Two wrenches are used to tighten the pipe. The pipe is made from a material having an allowable…
A: The maximum allowable shear stress is The outer diameter of pipe is The inner diameter is
Q: I want to explain how to count j1 (half joints) and j2 (full joints) in the degree of freedom and…
A:
Q: Plz solve correctly
A: The objective of the question is to find the center of mass of a uniform slice of pizza with radius…
Q: Problem 3: Calculate the horizontal velocity v with which the 48-lb carriage must strike the spring…
A: The weight of the carriage,
Q: 1
A: The stress in the Aluminum shell is -0.2544ksi. Explanation:For thermal expansion…
Q: A student working 3.0m away from you in a chemistry lab performs an experiment which creates a bad…
A:
Q: The mass of the bar shown is m = 4 kg and its length is I = 1.2 m. The spring constant is K = 180…
A: The mass of bar is The length is The spring constant is The initial angular velocity is The initial…
Q: Two wooden members are joined by plywood splice plates that are fully glued on the contact surfaces.…
A: Wooden Member
Q: How many forces are acting in X Direction? Hint: Draw FBD and break forces into Components
A:
Q: Problem 1: The inlet of a jet engine flying at supersonic speed (M∞ > 1) is supposed to compress…
A: Given data:Inlet area = AiThroat area = A*Area ratio= 1.3and, throat is always sonicThe objective of…
Q: A block of mass m = 2.00 kg is attached to a spring of force constant k = 525 N/m as shown in the…
A:
Q: (b) The gudgeon pin is used to connect the piston and the connecting rod. Show from first principles…
A: The objective of the question:Show that the maximum bending moment acting on the gudgeon pin is…
Q: find trasfer function Y(s)/R(s) if kc is 5 and plant is 1/(0.5s+1). input r(t) is a unit-step…
A: The transfer function as you have asked is: T(s)=0.5s+65 It can be simplified by taking 0.5 common…
Q: Rod BD is made of steel (E= 29 × 100 psi) and is used to brace the axially compressed member ABC.…
A:
Q: PROBLEM: Represent the translational mechanical system shown in Figure 3.15 in state space about the…
A:
Q: Motiyo Add explanation
A: The objective of the question is to determine the reactions at point A of a cantilever beam…
Q: Hi, I have been given this pin-jointed frame analysis to solve (see pictures of the structure…
A:
Q: Two cylinders act right after one another. Each cylinder is metered, and some actions are slow, and…
A: Given below solution Explanation:Step 1: Step 2: Step 3: Step 4:
Q: 1.6 (A). An I-seetion girder is constructed from two 80 mm x 12 mm flanges joined by an 80 mm x 12…
A:
Q: A 1.1 kg metal head of a geology hammer strikes a solid rock with a speed of 3.1 m/s. Assuming all…
A:
Q: Consider a commercial airliner flying at a speed of 540 mph (relative to the air) at an altitude of…
A: Givenairline flying at a speed altitude means molar mass, (M) temperature variation with altitude is…
Q: 6 Three wooden beams and two steel plates are securely bolted together to form the composite member…
A: The largest permissible bending moment when the member is bent about horizontal axis is 115.958…
Q: An oil well has the following specifications; • Tubing diameter = 2.875” • Tubing roughness = 0.0254…
A:
Q: Question 3 (Type B): Determine the magnitude of the force in each member of the truss using the…
A: Here method of joints is used.
Q: 1.2 (A). A steel tube, 25 mm outside diameter and 12 mm inside diameter, carries an axial tensile…
A:
Q: Gas at 70 bars gage pressure and 37.8°C is contained in a 12,900-cm3 cylinder. A piston compresses…
A: The gas gage pressure is = 70 barAtmospheric pressure is = 1.01325 barThe temperature is T1=37.8…
Q: Question 2: As it passes the position shown, the particle P has a constant speed v = 100 m/s along…
A:
Q: In copper, what percentage of the volume change which occurs as the specimen is heated from room…
A: Linear thermal expansion coefficient of copper:Melting point temperature isRoom temperature can be…
Q: A 750-g collar can slide along the horizontal rod shown. It is attached to an elastic cord with an…
A: The mass of the collar is m = 750 g.The spring constant of the cord is k = 210 N/m.The unstretched…
Q: An object of characteristic length L = 0.5 m is 10°C warmer than the surrounding fluid, which is…
A: 1. Reynolds number:Write expression for Reynolds number. ...... (1)Here V is fluid…
Q: Refrigerant 134a enters an air conditioner compressor at 4 bar, 20 degrees celsius, and is…
A:
Q: Please don't provide handwritten solution ...
A: Hence the Moment Diagram as shown belowExplanation:Step 1: A continuous beam is laid on three…
Q: Water steam is running through the nozzle. Inlet pressure is P1=25 bars; T1=300C; V1=90m/s;…
A: a) Exit velocity 577.148 m/sb) Inlet diameter 0.5046 m Outlet diameter 0.029 mExplanation:
Q: Determine an equivalent lumped mass model for the crankpin.
A: To determine an equivalent lumped mass model for the crankpin, you would typically follow these…
Q: 6-125 A heat pump designer claims to have an air-source heat pump whose coefficient of performance…
A: Answer Explanation:Step 1: Step 2: Step 3: Step 4:
Q: Question 3: The cast iron of a small press has a cross section as shown. For Q = 16-kips, determine:…
A:
Q: Part A Consider the frame shown in (Figure 1). Determine the x and y components of force that the…
A:
Q: isn't h1 154.99?
A:
Q: The device shown in figure below can be analyzed as a pin-jointed fourbar mechanism in series with a…
A: The angle made by the link OC with the horizontal axis, The length of the link AB, The length of the…
Q: A bare slab fuel element is 0.2 inches thick with a thermal conductivity of 10 BTU/hr-ft-F. It…
A: This problem involves heat conduction in a slab and can be solved using the heat conduction…
Q: Give brief description of magnetic flowmeter? Can one use such flowmeter to measure the flow of non…
A: The answers are provided below.
Q: A spring with a 2-kg mass and a damping constant 1 can be held stretched 1 meters beyond its natural…
A:
Q: Find normal stress at a,b,c,d (t wall = 10mm)
A: Stress at A =39.826MPaStress at B = 32.234 MPaStress at C = 7.052 MPaStress at D = -0.54 MPa#…
Q: When a sample of a real gas expanded adiabatically and reversibly, its pressure changed from 10.0…
A: Given:The initial pressure, The final pressure, The temperature dropped,
Q: find the transfer function Y(s)/R(s)
A: The transfer function is Y(s)/R(s)=(14s+56)/(s3+10s2+31s+16)Explanation:
Q: A 1.5 kW motor is running at 1440 rev/min. It is to be connected to a stirrer running at 36 rev/min.…
A: Given Data, Motor Power(P)=1.5 KWSpeed(N)=1440Stirrer speed(N1)=36
Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…
A:
Q: 24. The three branches of a hydraulic system require flow rates of 12, 25, and 18 gpm, respectively.…
A: Given:flow rates from the three branches of hydraulic system:Find:the correct reservoir size that…
Q: Please write a matlab code to Solve this
A:
Step by step
Solved in 1 steps
- Repeat Problem 2.3-18, but assume that the bar is made of copper alloy. Calculate the displacements SBand Scif P = 50 kips, L = 5 ft = 3/5 in., b1= 2.75 in., b2= 3 in., and E = 16,000 ksi.Three round, copper alloy bars having the same length L but different shapes are shown, in the figure. The first bar has a diameter d over its entire length, the second has a diameter d over one-fifth of its length, and the third has a diameter d over one-fifteenth of its length. Elsewhere, the second and third bars have a diameter Id. All three bars are subjected to the same axial load P. Use the following numerical data: P = 1400 kN, L = 5m,d= 80 mm, E= 110 GPa. and v = 0.33. (a) Find the change in length of each bar. (b) Find the change in volume of each bar.Repeat Problem 10.3-15 using L = 3.5 m, max = 3 mm, and EI = 800 kN·m2.
- A square wood platform is 8 ft × 8 ft in area and rests on masonry walls (see figure). The deck of the platform is constructed of 2-in. nominal thickness tongue-and-groove planks (actual thickness 1.5 in.; sec Appendix CL) supported on two S-ft long beams. The beams have 4 in. × (i in. nominal dimensions (actual dimensions 3.5 in. × 5.5 in.). The planks arc designed to support a uniformly distributed load n ( lb/ft" i acting over the entire top surface of the platform. I be allowable bending stress for the planks is 2400 psi and the allowable shear stress is 100 psi. W ben analyzing the planks, disregard their weights and assume that their reactions are uniformly distributed over the top surfaces of the supporting beams. (a) Determine the allowable platform load Mr. (lb/ft2) based upon the bending stress in the planks. (b) Determine the allowable platform load if-. (lb/ft-) based upon the shear stress in the planks. (c) Which of the preceding values becomes the allowable load alolow on the platform? Hints: Use care in constructing the loading diagram for the planks, noting especially that the reactions are distributed loads instead of concentrated loads. Also, note that the maximum shear forces occur at the inside faces of the supporting beams.Rigid bar ACB is supported by an elastic circular strut DC having an outer diameter of 15 in. and inner diameter of 14.4 in. The strut is made of steel with a modulus elasticity of E = 29,000 ksi. Point load P = 5 kips is applied at B. Calculate the change in length of the circular strut DC. What is the vertical displacement of the rigid bar at point B?Repeat Problem 2.4-8, but assume that the bar is made of aluminum alloy and that BC is prismatic. Assume that P = 20 kim. L = 3 ft.t = 314 in., b1 2m.b 2.Sin.andElO.400ksi.
- A hollow circular tube T of a length L = 15 in. is uniformly compressed by a force P acting through a rigid plate (see figure). The outside and inside diameters of the tube are 3.0 and 2.75 in., respectively. A concentric solid circular bar B of 1.5 in. diameter is mounted inside the lube. When no load is present, there is a clearance c = 0.0I0 in. between the bar B and the rigid plate. Both bar and tube are made of steel having an c[autoplastic stress-strain diagram with E = 29 X LO3 ksi and err= 36 ksi. (a) Determine the yield load Pt- and the corresponding shortening 3yof the lube. (b) Determine the plastic load Ppand the corresponding shortening Spof the tube. (c) Construct a load-displacement diagram showing the load Pas ordinate and the shortening 5 of the tube as abscissa. Hint: The load-displacement diagram is not a single straight line in the region 0 ^ P ^ PrSolve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield stress is 590 MPa, and the factor of safety is 3.0. (a) Determine the required thickness to the nearest millimeter. (b) If the tank wall thickness is 85 mm, what is the maximum permissible internal pressure?A sign for an automobile service station is supported by two aluminum poles of hollow circular cross section, as shown in the figure. The poles are being designed to resist a wind pressure of 75 lb/ft" against the full area of the sign. The dimensions of the poles and sign are hx= 20 ft, /r =5 ft, and h = 10 ft. To prevent buckling of the walls of the poles, the thickness e is specified as one-tenth the outside diameter d. (a) Determine the minimum required diameter of the poles based upon an allowable bending stress of 7500 psi in the aluminum. (b) Determine the minimum required diameter based upon an allowable shear stress of 300 psi.