Two wrenches are used to tighten the pipe. The pipe is made from a material having an allowable shear stress of Tallow = 90 MPa. The pipe has an outer diameter of 25 mm and inner diameter of 20 mm. (Figure 1) Determine the maximum allowable force P that can be applied to each wrench. Express your answer to three significant figures and include the appropriate units. P = Value Submit Request Answer Units

Two wrenches are used to tighten the pipe. The pipe is made from a material having an allowable shear stress of Tallow = 90 MPa. The pipe has an outer diameter of 25 mm and inner diameter of 20 mm. (Figure 1) Determine the maximum allowable force P that can be applied to each wrench. Express your answer to three significant figures and include the appropriate units. P = Value Submit Request Answer Units

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.9.3P: A vertical pole consisting of a circular tube of outer diameter 5 in. and inner diameter 4.5 in. is...

See similar textbooks

Similar questions

The shear stresses t in a rectangular beam arc given by Eq. (5-43): in which Fis the shear force, / is the moment of inertia of the cross-sectional area, /lis the height of the beam, and i] is the distance from the neutral axis to the point where the shear stress is being determined (Fig. 5-32). By integrating over the cross-sectional area, show that the resultant of the shear stresses is equal to the shear force V.
A thin-walled rectangular tube has uniform thickness t and dimensions a x b to the median line of the cross section (see figure). How does the shear stress in the tube vary with the ratio = a/b if the total length Lmof the median line of the cross section and the torque T remain constant? From your results, show that the shear stress is smallest when the tube is square (ß = 1).
A typical stainless steel cylindrical vessel is shown. The inside diameter of the tank is 48.0 in. and the wall thickness is 0.75 in. The tank is pressurized to 1.40 ksi. Determine the absolute maximum shear stress on the inner surface of the cylinder wall.
A torque of 2 kip # in. is applied to the tube. If the wall thickness is 0.1 in., determine the average shear stress in the tube.
Internal loadings at a critical section along a steel drive shaft are given. If the yield stress under tension and shear are S_y = 800 MPa, respectively, determine the maximum length of the shaft using the maximum-shear-stress theory (Tresca yield theory) in a way that the shaft does not fail neither at A nor at B
The drive shaft of a car with diameter 30 mm is designed to transmit a power of 50 kW when rotating at 2100 rpm. The drive shaft material has an allowable shear stress of 230 MPa. i) Determine the maximum shear stress in the shaft. ii) In order to reduce the weight of the vehicle, a hollow shaft is proposed with a maximum outer diameter of 30 mm. Determine, the maximum inner diameter iii) Determine the resultant percentage weight reduction
The internal loadings at a critical section along the steel drive shaft of a ship are calculated to be a torque of 2300 lb # ft, a bending moment of 1500 lb # ft, and an axial thrust of 2500 lb. If the yield points for tension and shear are sY = 100 ksi and tY = 50 ksi, respectively, determine the required diameter ofthe shaft using the maximum shear stress theory.
The pipe assembly shown is subjected to a force F = 400 N. The pipe has an inner diameter of 20 mm and an outer diameter of 30 mm. It is made of steel with Sy = 250 MPa. Determine the safety factor at point A using the maximum shear stress theory. Select one: a. NA = 1.843 b. NA = 3.224 c. NA = 2.580 d. NA = 4.299
A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 20 mm. The diameter of the pressure vessel is 450 mm, and its length is 2.0 m. Determine the maximum internal pressure that can be applied if the longitudinal stress is limited to 140 MPa, and the circumferential stress is limited to 60 MPa.
The drive shaft AB of an automobile is made of a steel having allowable shear stress of tallow = 8 ksi. If the outer diameter of the shaft is 2.5 in. and the engine delivers 200 hp to the shaft when it is turning at 1140 rev>min, determine the minimum required thickness of the shaft’s wall.
a hollow shaft for a rotary compressor is to be designed to transmit maximum torque of 4750 n-m. the shear stress in the shaft is limited to 50 mpa. determine the inside outside diameter of the shaft if the ratio of inside to outside diameter of the shaft is 0.4
Two fork-end pieces are to be joined together by a single steel pin of 25 mm diameter and they arerequired to transmit 50 kN. Determine the minimum cross-sectional area of material required in one branch of eitherfork if the stress in the fork material is not to exceed 180 MN/m2. What will be the maximum shear stress in the pin?1.39 x 10 m*; 50.9 MN/m*]