Answered: Calculate the fluid force on a side of…

Name: 13. Calculate the fluid force on a side of the plate in Figure 11(A),
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: 13. Calculate the fluid force on a side of the plate in Figure 11(A),submerged in water, assuming that the top of the plate is at adepth of D = 2 m.2 mD4 m2 m4 m7 m2 m8.3 EXERCISES(A)(B)Rogawski et al., Calculus, 4e, © 2019 W. H. Freeman andCompanyF

Engineering

Mechanical Engineering

Calculate the fluid force on a side of the plate in Figure 11(A), submerged in water, assuming that the top of the plate is at a depth of D = 2 m. 2 m D 4 m 4 m 2 m 7 m 2 m

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.76P: A 6-in. diameter hole is drilled in the conical frustum. Calculate the volume and the surface area...

See similar textbooks

Similar questions

Is bouyant force acting on the body submerged increasing as the object goes deeper into the water? Yes or No. Explain your answwer.
A brass sphere (sp. gr. 8.60) is placed in body of mercury. If the diameter of the sphere is 30 cm (a) what minimum force would be required to hold it submerged in mercury? (b) What is the depth of flotation of the sphere when it is floating freely? NOTE: CLEAR HANDWRITTEN SOLUTION
The 6-ft-radius waterwheel in Fig. is being used tolift water with its 1-ft-diameter half-cylinder blades. If thewheel rotates at 10 r/min and rigid-body motion is assumed,what is the water surface angle θ at position A ?
Three types of fluids stack in an open tank as shown in the picture. If the specific gravidties are sg1=1, sg2=1, sg3=1, and h1=0 m, h2=0 m, h3=0 m, calculate the gage pressure at location 4, P4(gage)=_________(kPa)
Calculate the fluid force on one side of a 5 ft by 5 ftsquare plate if the plate is at the bottom of a pool filled with waterto a depth of 8 ft anda. lying flat on its 5 ft by 5 ft face.b. resting vertically on a 5-ft edge.c. resting on a 5-ft edge and tilted at 45° to the bottom of the pool
plzzzzzzzz heeeelp meeee right nowww What would be the rotation rate (in rad/sec) if during rotation the water in the right leg (with a diameter of d) decreases a distance h1=0.10 m?
The tank of water in Fig. is 12 cm wide into the paper.If the tank is accelerated to the right in rigid-body motion at6.0 m/s 2 , compute ( a ) the water depth on side AB and ( b ) thewater-pressure force on panel AB . Assume no spilling.
In Fig. , vertical, unsymmetrical trapezoidal panelABCD is submerged in fresh water with side AB 12 ft belowthe surface. Since trapezoid formulas are complicated,( a ) estimate, reasonably, the water force on the panel, in lbf,neglecting atmospheric pressure. For extra credit, ( b ) lookup the formula and compute the exact force on the panel.
End D of a 2.5 long uniformly plain wooden rod( s.g=0.7) is held 0.3m below the surface of still water. (a.) How much of the rod remains above the water surface? (b.) if the rod diameter is 25mm what force of D is required to hold it in place ?
What force, F, must be applied to the S-shaped gate to keep it closed? The gate is 1 m wide andthe radius of curvature of each part is 1 m. The liquid is water.
An elliptical plate, major axis 6 feet and minor axis 4 feet, is submerged vertically until its minor axis lies in the surface of the water (weight density =p Ib/fr3). Determine the appropriate integral to be used to determine the force on one side of the submerged
A semicircular gate with a diameter of 6 ft is installed at 50º as shown below. The top of the gate is 5 ft below the water surface. Determine the resulting hydrostatic force and the location of the center of pressure on the gate.