Calculate the force and moment reactions at the bolted base O of the overhead traffice-signal assembly. Each traffic signal has a mass of 39 kg, while the masses of members OC and AC are 66 kg and 57 kg, respectively. Positive answers are to the right, up, and counterclockwise. A 39 kg Answers 6.5 m 39 kg B G 1.0 m 57 kg 5.5 m 66 kg C 7.6 m

Calculate the force and moment reactions at the bolted base O of the overhead traffice-signal assembly. Each traffic signal has a mass of 39 kg, while the masses of members OC and AC are 66 kg and 57 kg, respectively. Positive answers are to the right, up, and counterclockwise. A 39 kg Answers 6.5 m 39 kg B G 1.0 m 57 kg 5.5 m 66 kg C 7.6 m

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.11P: The figure is a model for member CDE of the frame described in Prob. 4.10. Draw the FBD of the...

See similar textbooks

Similar questions

The figure is a model for member CDE of the frame described in Prob. 4.10. Draw the FBD of the member, neglecting its weight. Count the unknowns.
Draw the FBD for the bar described in Prob. 5.1 if the bar is homogeneous of mass 50 kg. Count the unknowns.
The two uniform cylinders, each of weight W, are resting against inclined surfaces. Neglecting friction, draw the free-body diagrams for each cylinder and for the two cylinders together. Count the total number of unknowns and the total number of independent equilibrium equations.
An athlete of 60 kg and 1.70 m tall performs the ring exercise called "the Christ", in which he keeps his body immobile with his arms extended horizontally as shown in Fig.-Prob.17(a). The angle with the vertical of the cords from which the rings hang is theta = 10. (a) Determine the tension T in the cords holding the rings. (b) Considering each arm of the athlete as a rigid horizontal bar subjected to the forces indicated in Fig.-Prob.17(b), calculate the value of the components RX and RY, the value of the reaction “R” and of the beta angle.- W is the weight of the arm, applied in the middle of its length.- R is the reaction at the shoulder joint O.- RX and RY are the horizontal and vertical components respectively of the reactionapplied at the shoulder joint O.- Note: Consider that the mass of each arm of the athlete is 3% of the total mass, and thatthe length of the arm is equal to 35% of its height. Fig.-Prob.17(a): Man performing the position of "The Christ"Fig.-Prob.17(b):…
At the shown position, the ground reaction forces measured using a force platform are 600N in the vertical direction (Fy) and 200N in horizontal direction (Fx). The mass of the limb below the knee is 4kg with the centre of gravity at the point G. Determine the forces and moment applied to the knee joint. Draw correct free body diagram using any part of the body shown below.
The mass center G of the 1300-kg rear-engine car is located as shown in the figure. Determine the normal force under each tire when the car is in equilibrium. State any assumptions.
The jib crane is designed for a maximum capacity of 14 kN, and its uniform I-beam has a mass of 270 kg. Plot the magnitude R of the force on the pin at A as a function of x through its operating range of x = 0.2 m to x = 4.0 m. On the same set of axes, plot the x- and y-components of the pin reaction at A. Do these plots on a separate piece of paper. Then answer the following questions in Wiley Plus as a check for your work. (You can disregard the plot, I only need a, b, c, and d)
The jib crane is designed for a maximum capacity of 7 kN, and its uniform I-beam has a mass of 240 kg. Plot the magnitude R of the force on the pin at A as a function of x through its operating range of x = 0.2 m to x = 3.7 m. On the same set of axes, plot the x- and y-components of the pin reaction at A. Do these plots on a separate piece of paper. Then answer the following questions in Wiley Plus as a check for your work.(a) What is the value of R when x = 1.9 m?(b) What is the value of R when x = 3.2 m?(c) Determine the minimum value of R and the corresponding value of x.(d) For what value of R should the pin at A be designed?
Neglecting friction and the weights of the members, compute the magnitudes of the pin reactions at A and C for the folding table shown. https://imgur.com/a/q744W8J
PROBLEM 1: The 1500-kg beam ABC has fixed support at A and connected to beam BD by hinge at B. Beam BD has a mass of 2000 kg and supported by a cable at D. The cable is attached to the 20-cm-diameter pulley at E and pulled vertically at the other end, by tension T. Given: a = 1.5 m; b = 0.9 m; c = 1.8 m d = 0.6 m; e = 1.4 m; θ = 75°. Calculate the required tension to maintain in equilibrium. (ANSWER: 12.830KN) Calculate the moment reaction at A. (ANSWER: 28.499) Calculate the total reaction at A. (ANSWER: 22.192) Calculate the vertical reaction at E. (ANSWER: 25.223)
Determine the horizontal and vertical components of reaction which the pins exert on member AB of the frame. 24.1 The magnitude of the component of reaction Bx is Blank 1 kN. 24.2 The magnitude of the component of reaction By is Blank 2 kN. 24.3 The magnitude of the component of reaction Ax is Blank 3 kN. 24.4 The magnitude of the component of reaction Ay is Blank 4 kN.
The mass of the uniform bar ABis 40 kg. Calculate the couple Crequired for equilibrium if a.θ = 0 b.θ = 54°