Calculate the force required by the hydraulic cylinder of a utility lift vehicle as shown in the figure below to maintain the position of the bucket. Draw all necessary diagrams and show step-by-step working. 1200 N 5 m 2.0 m 2.4 m 1.2 m 0.9 m

Calculate the force required by the hydraulic cylinder of a utility lift vehicle as shown in the figure below to maintain the position of the bucket. Draw all necessary diagrams and show step-by-step working. 1200 N 5 m 2.0 m 2.4 m 1.2 m 0.9 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The two blocks used in a measuring device have negligible weight. The spring is compressed 5 in.…

A: The two blocks used in a measuring device have negligible weight. The spring is compressed 5 in.…

Q: 3-38. The block has a weight of 20 lb and is being hoisted at uniform velocity. Determine the angle…

Q: A football player A throws a football C with a velocity of 20 m/s in the direction shown. Player B…

Q: Water enters an internally reversible turbine at 2 MPa, 400oC and exits at 150 kPa. Heat transfer,…

Q: A Lassonde Startup Company aims to expand its pump business into rural areas, where accessing clean…

Q: An oil pump operating at steady state delivers oil at a rate of 6 kg/s through a 2.5-cm- diameter…

A: The density of oil is .The mass flow rate is .The rise of pressure from inlet to outlet is .The…

Q: With the manometer reading as shown in Fig. 2.33, calculate the difference of pressures in the two…

Q: Determine the Prandtl number, Nusselt number, and Reynolds number from the following flow data: Cp =…

A: Determine the Prandtl number, Nusselt number, and Reynolds number from the following flow…

Q: A 1000 kg automobile accelerates from 10 km/hr to 120 km/hr. How much work does this require?

A: Question(4)Given:Mass Initial Velocity Final Velocity To find:The required Work

Q: The diameters of the main rotor and tail rotor of a single engine helicopter are 7.51 m and 1.01 m,…

A: Diameter of main rotor, Diameter of tail rotor, Rotational speed of main rotor, Rotational speed of…

Q: A Carnot heat engine operates between 1000°F and 50°F, producing 120 BTU of work. What is the heat…

Q: and indicate, with arrows, the directions of working fluid flow. b. Determine the required operating…

A: To draw temperature entropy drawing R 22 fluid, to calculate operating pressures and quality at…

Q: 3m A Sm. z (8₂) 450 N Find the reactions in Points A and G B 2m 4 m 3 m y (₂)

Q: What is the moment that the water exerts about the bottom edge of the dam (point P)?

Q: The machine shown is used to help load luggage into airliners. The combined mass of the conveyor and…

A: Initially, we will disassemble the apparatus and create the conveyor's free-body diagram.The baggage…

Q: Two electric motors are being considered to drive a centrifugal pump. Each motor is capable of…

A: Given:P = 90 hpMARR = 5%To find:Annual cost of electric power

Q: For a fibrous composite with fibers that are randomly and uniformly oriented within a specific…

A: A fibrous composite with fibres that are randomly and uniformly oriented within the specific…

Q: The collar C in Fig. 16-16a is moving downward with a velocity of 2 m/s. Determine the angular…

A: The collar C in Fig. 16-16a is moving downward with a velocity of 2 m/s. Determine the angular…

Q: Member AB is supported by BC and at A by a single journal bearing with a square shaft. Determine the…

A: Free body diagram:Position vector:System A will move up and down, therefore there won't be any…

Q: Use the Shell Balance approach for the Mass conservation of Species a transporting in species b,…

Q: Use one main program and then a subprogram to machine the pockets. Write the subprogram in absolute…

A: We must create both the main program code and the subprogram code in order to address the…

Q: 1. (a) Given a discrete signal x[0] = 1, x[1] = -1, x[2] = 1, x[3] = -1, compute the DFT X[k]. Use…

Q: 5 m 150 kN B 5 m El constant E-70 GPa 7 = 1000 (106) mm¹ 5 m D

Q: e state of stress at a point in a member is shown on the rectangular stress element in (Figure 4)…

Q: Sketch an induced draft counter-flow cooling tower, showing how it may be regulated to control the…

Q: In the following figure, a machine is installed in the water drainage system. Knowing that the…

Q: Determine the COP of a refrigerator that removes heat from the food compartment at a rate of 5250…

A: The refrigerantion effect is .The power consumed by compressor is

Q: 4.7* Near to the point where I am standing on the surface of Planet X, the gravitational force on a…

A: To solve this problem, let's break it down step by step.(a) Work done by gravity:The work done by…

Q: For the beam ABC loaded as shown below, (a) draw the shear force and bending moment diagrams, and…

A: For the beam ABC loaded as shown below, (a) draw the shear force and bending moment diagrams, and(b)…

Q: 3. A992 steel W beam; max. deflection ≤ ½ in. 5 kip/ft. 18 ft. B

A: to determine the shear force, bending moment of the triangular loaf in cantilever beam, length of…

Q: Problem 16.137 At the instant shown in (Figure 1), rod AB has an angular velocity WAB = 3.0 rad/s…

Q: The cars on the amusement-park ride rotate around the axle at A with a constant angular velocity…

A: The angular velocity frame is .The angular velocity of axle is .

Q: 2. The heat pump for my house has a 4 kW compressor motor. I wish to keep my house at 25°C. My house…

Q: Q/Derivation of b.c.c equations with atomic compaction 4R V3 a

A: BCC crystal structure is given.We have to derive bcc equations with atomic compaction.

Q: A woman enters an elevator, stands on a scale, and presses the "up" button. Her normal weight is 550…

A: This question is based on the concept of free body diagram from Mechanics.

Q: The air conditioning system of 90 kPa total pressure. The data is shown in the figure. determine the…

Q: 1. Combine the two forces H and I, which act on the fixed structure at B, into a single equivalent…

Q: in the truss below, the maximum force(s) will occur in members GF, AF, or AB. What component…

A: In the truss below, the maximum force(s) will occur in members GF, AF, or AB.What component sustains…

Q: Two blocks A and B have a weight of 10 lb and 6 lb, respectively. They rest on the inclined plane…

A: Two blocks A and B have a weight of 10 lb and 6 lb, respectively.They rest on the inclined plane…

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

A: need force for memebers EG, DG and DF.A Pratt roof truss is shown. Take P= 9.6 KN.

Q: 3)Design a V – Belt drive to the following specifications Power transmitted = 75kw Speed of driving…

Q: A technician states that the master cylinder has a piston radius of .75" and the calliper piston has…

A: Write expression for total force exerted on master piston.Evaluate pressure exerted on master…

Q: 4) For the mechanical system shown below, find the transfer function T(s) = V₂(s)/R(s) Friction b₂…

A: The free body diagram of mass M2 is:andthe free body diagram of mass M1 is;and from (2);

Q: With the the following modifications: Change the 30 degree angle of the 4 kN force to 15 degrees

A: Consider a free body diagram below:First diagram is the components of force in horizontal and…

Q: A spherical tank,the inner diameter 50 cm and is maintained at temperature of 50c,the outer…

Q: 3. 1500 N The rod below has a diameter of 40mm. Find the stresses acting at point A. Hint: draw 3…

Q: ed The robot arm moves the paint gun to 0.95 m directly above the car. The voltage between the car…

A: To determine:the speed with which a paint droplet will hit the car.Given:The voltage between the car…

Q: Problem 2.132 The end B of a robot arm is moving vertically down with a constant speed vo= 2 m/s.…

A: v0=2 m/sd=1.5 mthe free body diagram:

Q: With a base schedule as shown below, what changes will occur if activity C can start after B is…

A: Here alphabets indicate activity and numbers indicate activity processing time.

Q: Plz see attached pic Need Force for Member AC Member BC

Concept explainers

Basic Terminology in Mechanics

The area of science and mathematics concerned the motion of the objects, the relation between the force matter, and motion if specified. Forces exerted over the objects result in displacements or changes in the position of an object concerning its environment. This branch of physics keeps its roots in Ancient Greece in the form of the scripts of Aristotle and Archimedes.

Question

Calculate the force required by the hydraulic cylinder of a utility lift vehicle as shown in the figure
below to maintain the position of the bucket. Draw all necessary diagrams and show step-by-step
working.
1200 N
5 m
2.0 m
2.4 m
1.2 m
0.9 m
+

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Draw the free-body diagram of the member that is connected to the bucket.

VIEW

Step 2: Apply trigonometry to calculate the angles shown in the diagram.

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A Hydraulic press has a ram of 30 cm diameter and a plunger of 2 cm diameter. It is used for lifting a weight of 35 kN. How much force is required at the plunger? a. 311.1 kNb. 466.6 kNc. 233.3 kNd. 155.5 kN
A force of 30 N is applied to the input piston of a hydraulic jack. If the input and output piston have areas of 0.2 m² and 0.8 m², respectively, what is the minimum weight that can be lifted by the jack?
.A flywheel rim has a mean diameter of 500 mm and weight 120 kg. The density of the flywheel material is 7200 kg/m3. Which of the following is the thickness of the flywheel if the rim width is twice its thickness? choices: 146 mm 103 mm 52 mm 73 mm
A dictionary is pulled to the right at constant velocity by a 10 N force acting 30° upward above the horizontal. The coefficient of kinetic friction between the book and the horizontal surface is 0.5. What is the weight of the book?
A pull of 60 N inclined at 25° to the horizontal plane is required just to move a body placed on a rough horizontal surface. But the push required to move the body is 75 N. Find the weight of the body and coefficient of friction
A pull of 20 N at 30° to the horizontal is necesary to move a block of wood on a horizontal table. If the coefficient of friction between the bodies in contact is 0.25, what is the weight of the block
A mechanic is lifting a car of 2000kg using a screw jack as he applies a force of 100 N. The screw jack handle is 600 mm, and the screw pitch is 10 mm. Calculate the following; Mechanical advantage Velocity ratio Efficiency
21 A 180-kg block is resting on a 25 deg inclined plane with a coefficient of friction = 0.8. Find the required horizontal force P (kN) that is necessary to start the block UP the incline. ROUND OFF TO TWO DECIMAL PLACES.
The larger and smaller pulleys of a chain block has 31 and 29 recesses respectively. If the efficiency is 45% when raising a load of 8kN, calculate, 6.1 the effort required 6.2 the effective distance through which the effort must move in order to lift the load 350 mm.
An object weighing 400 N is held by a rope that passes over a horizontal drum. The coefficient of friction between the rope and the drum is 0.25. If the angle of contact is 150 degrees, determine the force that will raise the object.
Five movable pulleys are arranged as in the first system of pulleys. If the efficiency of the system is 80%. Find the effort required to raise a load of 1000kg.
a 200 kg box is on the platform of a weighing scale and is being pulled by a force of 70 kg acting at 43° above the horizontal. between the box and the platform the coefficient of friction is 0.36 . (A) How much will the scale register? (B) Will the box remain on the platform or slide?