Calculate the heat loss per linear foot from a 10 in. nominal pipe (outside diameter-10.75 in) covere with a composite pipe insulation consisting of 1 % in of insulation I placed next to the pipe and 2 In c Insulation II placed upon insulation I. Assume that the inner and outer surface temperatures of th composite insulation are 700 deg F and 110 deg F respectively, and that the thermal conductivity c material I is 0.05 Btu/hr-ft-deg F and for material Il is 0.039 Btu/hr-ft-deg F. Select the correct response. O 126 Btu/hr-ft 123.13 Btu/hr-ft 120 Btu-hr-ft 323.13 Btu/hr-ft Continue>

Calculate the heat loss per linear foot from a 10 in. nominal pipe (outside diameter-10.75 in) covere with a composite pipe insulation consisting of 1 % in of insulation I placed next to the pipe and 2 In c Insulation II placed upon insulation I. Assume that the inner and outer surface temperatures of th composite insulation are 700 deg F and 110 deg F respectively, and that the thermal conductivity c material I is 0.05 Btu/hr-ft-deg F and for material Il is 0.039 Btu/hr-ft-deg F. Select the correct response. O 126 Btu/hr-ft 123.13 Btu/hr-ft 120 Btu-hr-ft 323.13 Btu/hr-ft Continue>

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter9: Heat Transfer With Phase Change

Section: Chapter Questions

Problem 9.17P

See similar textbooks

Similar questions

1.4 To measure thermal conductivity, two similar 1-cm-thick specimens are placed in the apparatus shown in the accompanying sketch. Electric current is supplied to the guard heater, and a wattmeter shows that the power dissipation is 10 W. Thermocouples attached to the warmer and to the cooler surfaces show temperatures of 322 and 300 K, respectively. Calculate the thermal conductivity of the material at the mean temperature in W/m K. Problem 1.4
3.10 A spherical shell satellite (3-m-OD, 1.25-cm-thick stainless steel walls) re-enters the atmosphere from outer space. If its original temperature is 38°C, the effective average temperature of the atmosphere is 1093°C, and the effective heat transfer coefficient is , estimate the temperature of the shell after reentry, assuming the time of reentry is 10 min and the interior of the shell is evacuated.
A section of a composite wall with the dimensions shown below has uniform temperatures of 200C and 50C over the left and right surfaces, respectively. If the thermal conductivities of the wall materials are: kA=70W/mK,kB=60W/mK, kC=40W/mK, and kP=20W/mK, determine the rate of heat transfer through this section of the wall and the temperatures at the interfaces. Repeat Problem 1.34, including a contact resistance of 0.1 K/W at each of the interfaces.
thick-walled tube of stainless steel [18% Cr, 8% Ni, k = 19 W/m · ◦C] with 2-cm inner diameter (ID) and 4-cm outer diameter (OD) is covered with a 3-cm layer of asbestos insulation [k = 0.2 W/m · ◦C]. If the inside wall temperature of the pipe is maintained at 600◦C, calculate he heat loss per meter of length. Also calculate the tube–insulation interface temperature.
Write the expression for critical radius of insulation for a cylindrical pipe. Consider aninsulated pipe exposed to the atmosphere. Will the critical radius of insulation begreater on calm days or on windy days? Why?
A thick walled tube of stainless steel with 20 mm inner diameter and 40 mm outer diameter is convered with a 30 mm layer of asbestos insulation (k = 0.2 W/m°C). If the inside wall temperature of the pipe is maintained at 600°C and the outside insulation at 1000°C, calculate the heat loss per metre of length.
Calculate the heat loss per foot from a 10 in. nominal pipe ( outside diameter = 10.75 in.) covered with a composite pipe insulation consisting of 1 ½ in of insulation A placed next to the pipe and 2 in. of insulation B placed upon insulation A. Assume that the inner and outer surface temperature of the composite insulation are 700°F and 110°F respectively , and that the thermal conductivity of material I is 0.05 Btu/ hr-ft-°F and for material II is 0.039 Btu/hr-ft-°F (Include illustration/Figure)
A cylindrical tank is constructed from aluminum (kal = 240 W/m2.K) with 1 m inner diameter and 10 mm thick. The tank having uniform volumetric heat generation of 1 MW/m3. The outer surface of the tank is covered with a 5 mm thick layer of stainless steel (kst = 15 W/m2.K). The heat transfer from the tank is assumed to the radial direction only as the both cross sections of the tank are properly insulated. It is proposed to submerge the tank into oceanic water at 20˚C flowing at a velocity of 0.5 m/s. The properties of the oceanic water are kwater = 0.606 W/m.K, ρ = 1000 kg/m3, μ = 959 x 10-6 N.s/m2, Pr = 6.62. Analyze the acceptability of the proposal if the melting point of aluminum is 667˚C.
A steel pipe 150mm diameter conveys steam at a temperature of 260 degrees and is covered by two layers of lagging, each 50mm thick. The thermal conductivity coefficient of the inside layer of lagging is 0.086W/m.K while that of the outside layer is 0.055W/m.K. The outside surface temperature of the steel pipe can be taken as the same as the temperature of the system. The ambient temperature is 27 degrees. Calculate the heat lost per hour for pipe length 30m. Calculate the interface temperature between the two layers of lagging
HEAT TRANSFER Calculate insulation thickness in mm (minimum value)required for a pipe carrying steam at 1800°C. The pipe sizeis 8 in and the maximum allowable temperature of outer wallof insulation is 500°C. Thermal conductivity of theinsulation material for the temperature range of the pipecan be taken as 0.04 W/m·K. The heat loss from steam permeter of pipe length has to be limited to 80 W/m. SHOW COMPLETE SOLUTION IN A PAPER
Superheated steam at 575ºC is routed from a boiler to the turbine of an electric power plant through steel tubes (k = 35 W/m K) of 300 mm inner diameter and 30 mm wall thickness. To reduce heat loss to the surroundings and to maintain a safe-to-touch outer surface temperature, a layer of calcium silicate insulation (k = 0.10 W/m K) is applied to the tubes, while degradation of the insulation is reduced by degradation of the insulation is reduced by wrapping it in a thin sheet of aluminium having an emissivity of ε= 0.20. The air and wall temperatures of the power plant are 27ºC. Assume that the inner surface temperature of a steel tube corresponds to that of the steam and the convection coefficient outside the aluminium sheet is 6 W/m2 K, (a) What is the minimum insulation thickness needed to ensure that the temperature of the aluminium does not exceed 50ºC? (b) What is the corresponding heat loss per unit meter?
A thick wallet tube of stainless steel (k+10 W/M°C) with 2 cm inside diameter and 4 cm outer diameter is covered with a 3 cm layers of asbestos insulation (K= 0.2 W/M°C), if the inside wall temperature of the pipe is maintained at 600 degree C , Calculate the heat loss per meter of length, Also calculate the tube - insulation interface temperature. Draw the Coresponding diagram. Ambient temperature is 2°C.