Calculate the latency (from first bit sent to last bit received) for: (a) 1-Gbps Ethernet with a single store-and-forward switch in the path and a packet size of 5000 bits. Assume that each link introduces a propagation delay of 10 us and that the switch begins retransmitting immediately after it has finished receiving the packet. (b) Same as (a) but with three switches.

Calculate the latency (from first bit sent to last bit received) for: (a) 1-Gbps Ethernet with a single store-and-forward switch in the path and a packet size of 5000 bits. Assume that each link introduces a propagation delay of 10 us and that the switch begins retransmitting immediately after it has finished receiving the packet. (b) Same as (a) but with three switches.

Operations Research : Applications and Algorithms

4th Edition

ISBN:9780534380588

Author:Wayne L. Winston

Publisher:Wayne L. Winston

Chapter20: Queuing Theory

Section20.10: Exponential Queues In Series And Open Queuing Networks

Problem 8P

See similar textbooks

Similar questions

Suppose that there are three inter-media nodes between Host 1 and Host 2, and the transmission rate of each link is 4.096 Mbps. The time of end-to-end circuit established is 0.5 second. How much seconds does it take to send a file of 8.192M byte from host H1 to host H2 over a packet-switched network?
1. Mention the protocols over which the protocol is encapsulated, to which layer ARP belongs. 2. What is the Target's Hardware Address = a8:9f:ec:bb:78:f0 in the frame and what is the Destination Address = a8:9f:ec:bb:78:f0 in the ARP request packet? Why? 3. Mention the protocol over which the ICMP protocol is encapsulated. - Explain a little in the answers
Consider a two-link network in which Host A has a 1 Mbps connection with a 10 ms propagation delay and the router has a 15 Mbps link with a 25 ms propagation delay. Host A sends Host B a 1500-byte packet. What is the packet transmission delay from the router to Host B (in milliseconds)?
Calculate the total time (in milliseconds) required to send a file of size of 8000 Bytes. Assume one-way propagation delay of 40 milli second on a link with bandwidth of 0.8 x106 Bytes/second and a packet size of 1000 Bytes where data packets can be sent continuously with no packet loss.
A TCP PDU of length 40,513 octets (including the TCP header) is to be transmitted over a physical link between two nodes at 1,064,218,818 bps using 802.3 with an MTU of 826 octets. Assume a LLC-PDU has an overhead of 4 octets and that the IP-PDU has no options. i) How many bits are sent over the connection from the source to destination assuming only full frames are sent? ii) What is the effective data rate from the TCP-PDU point of view (to nearest integer)? iii) If the propagation time between the two nodes is 5 microseconds what is the line efficiency to 3 decimal places assuming stop and wait is used between the two nodes?
A frame of 1200 bytes travel through five switches along the path. Each link has a bandwidth of 100 Mbps, a length of 100 m, and a propagation speed of 2 × 10*8 m/sec. Assuming a queuing and processing delay of 2 ms at each switch, what is the approximate end-to-end delay for this packet?
If there is a computer with the address 4A: 30: 10: 21: 10: 1A Sending a data frame to your Computer, specify the Destination Address and Source Address on the Ethernet frame, if the communication is done as i. Unicast. ii. Multicast. iii. Broadcast Table Fill in the following. Type of Communication Destination Address Source Address Unicast Multicast Broadcast
A factor in the delay of a store-and-forward packet-switching system is how long it takes to store and forward a packet through a switch. If switching time is 10 usec, is this likely to be a major factor in the response of a client-server system where the client is in New York and the server is in California? Assume the propagation speed in copper and fiber to be 2/3 the speed of light in vacuum.
Use again the network architecture provided in the figure above, were RS, RC and Ri for i = {1,2,3,4}, the transmission rates of the server link, client link and intermediate network links. Consider a message that is 60 · 106 bits long that is to be sent from client to server. Ignore propagation, queuing, and processing delays. a.Now assume that Rc = 60Mbps, Rs = 40Mbps, R1 = R3 = 30Mbps, R2 = 10Mbps and R4 = 20Mbps. Suppose that the message is segmented into 6000 packets, with each packet being 10,000 bits long. How long does it take to move the first packet from source host to the first switch? When the first packet is being sent from the first switch to the second switch, the second packet is being sent from the source host to the first switch. At what time will the second packet be fully received at the first switch? b) How long does it take to move the file from source host to destination host when message segmentation is used if path R3, R4 is chosen?
Identify the values of ToDS and FromDS in the 802.11 Mac data frame when Address 4 field has the sender address. Choose an answer A 0 and 1 B 0 and 0 C 1 and 0 D 1 and 1
In a Wireshark capture of the Ethernet II header contents of an ARP request, the destination address field value is ____________. 2 octets 4 octets 6 octets 8 octets How many types of footprinting are there? 4 2 5 3
Consider sending real-time data from Host A to Host B over a packet-switched network. Host A takes an 8-bit measurement every millisecond, and Host A collects these into 64-byte packets. There is one link between Hosts A and B; its transmission rate is 5 Mbps, its propagation delay is 2 × 108 meters/sec, and its length is 3 km. As soon as Host A gathers a packet, it sends the packet to Host B. How much time elapses from the time that Host A begins to take the first measurement in a packet until the entire packet reaches Host B?