Calculate the maximum contact exposure rate at the side surface of a 10-foot wide railcar loaded with steel scrap with a 2 curie Cs-137 source at the geometric center of the car. The TVL for scrap metal (typical density of 65 lbs/cubic foot) is 16 inches.

Calculate the maximum contact exposure rate at the side surface of a 10-foot wide railcar loaded with steel scrap with a 2 curie Cs-137 source at the geometric center of the car. The TVL for scrap metal (typical density of 65 lbs/cubic foot) is 16 inches.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter11: Heat Transfer By Radiation

Section: Chapter Questions

Problem 11.66P

See similar textbooks

Related questions

Q: Q2. As shown on the right in image below, the force Facting on the box varies with displacement s, a...

Q: find femperature, at the trißle point? Vapou pressure of liquid & Sofid ammoniay are respectivelcy g...

A: Write the expression for vapour pressure of liquid ammonia. lnP=14.15-3054T ...... (1) Write th...

Q: The shallow circular disk has a sharp-edged orifice at its center. A water jet of speed V strikes th...

Q: umed to be sinusoidal, the res kcited vibrations, are determine Es of the vehicle, stiffness ng. spe...

Q: -Reller

Q: Determine the acceleration (normal component) (m/s^2)of the plane. Round off your answer to the near...

A: Given data: v=550 m/s2a=50 m/s2θ=70° Need to determine the normal component of acceleration of the p...

Q: The gas constant R has the value 287 J/Kg * K for dry air. Using the ideal gas law (P = PdryRT): Fin...

Q: Compare a GPS and differential GPS in accordance to aircraft operations

A: GPS stands for Global Positioning System and differential GPS is also known as DGPS. The comparison ...

Q: t. Determine the velocity of car B

A: Determine the velocity of car B relative to Car A

Q: Need some assistance figuring this one out! , d1 = 3.3m , d2 = 1.7m , d3 = 2.9m , d4 = 4.2m , h = 6...

A: Calculated expression of AC as position vector (rACx , rACy , rACz ). And the length of cable AC. Ca...

Q: Can be manufactured by cast aluminum alloy only Nose Section Power Section Supercharger section Acce...

Q: Determine the time(s) when the acceleration of the vehicle becomes 20m/s^2. The car starts from rest...

Q: Draw an archemedian spiral of 1½ convulations with the greatest radius of 100mm and the smallest rad...

A: Draw an archemedian spiral of 1½ convulations with the greatest radius of 100mm and the smallest rad...

Q: A process to liquify nitrogen gas (N2) from 300K, 200atm to 98.69K (saturation temperature) and 7atm...

A: Given data, Initial temperature of the nitrogen, T1 = 300 K Initial pressure of nitrogen, P1 = 200 a...

Q: A steel wheel of 900mm diameter on a horizontal steel rail. It carries a load of 50ON. The coefficie...

A: Coefficient of rolling resistance =b= 0.1 Diameter d= 900 mm W= 500 N

Q: 2. Consider the belt and pulley system, as shown. Pulley B and pulley C are locked together. Determi...

A: As per given We have to determine angular speed of pulley D

Q: A uniform bar of weight 500N is held in honzontal position by 3 vertical wires as shown. Diameter of...

Q: 16. 1000CFM of air are compressed at constant temperature of 85°F and 198 psia to 580 psia. For both...

A: Given data: V=1000 CFMT1=T2=85°FP1=198 psiaP2=580 psia Need to determine the value of ∫pdv, -∫Vdp , ...

Q: (b) Is the 0.03 lb/10° Btu rule more or less restrictive than the 1 percent emission rule?

A: As shown in Table 3.1, there are two cases: (1) the plant began operations on September 18, 1978, an...

Q: For a thin-walled cylindrical pressure vessel with hemispherical end caps, constructed uniform thick...

Q: 4. The gauge of the Impact Testing Apparatus shows 52 divisions. Calculate the amount of energy adso...

A: Answer: The amount of energy absorbed per unit surface area prior to fracture is 1300 kJ/m2.

Q: Q2: A Freon -12 installation has the following data: Сараcity: Evaporator temperature : Condenser te...

A: A compressor, condenser, expansion device (which might be a valve, a capillary tube, an engine, or a...

Q: .) The vane is then fixed to a cart, which moves at a constant velocity Veart Vvane 2 m/s to the lef...

Q: Q3) A 16 lb cylinder stretches a spring 2/27 inches by itself. The spring is initially displaced 1/2...

A: according to the given data

Q: A single full penetration weld pass is made on a thin steel plate using a power input of 4 kW, and w...

A: Write the given data in the problem. Q=4 kW η=85% ux=10 mm/s ρc=0.005 J/mm3·°C t=5 m...

Q: For each state of an n-channel enhancement-mode MOSFET that follows, determine what operating region...

A: A n-channel MOSFET is made up of a p-type substrate that is implanted with two n-type materials that...

Q: DRAW THE THREE PROJECTION OF THE FOLLOWING SHAPE

A: According to the details provided in the question, we need to calculate three projection view

Q: a (m/s²) В 24 A 12 t (s) 30 60

A: for time t= 0 to 30 , a= (12/30 t a= 0.4 t a=(dV/dt)= 0.4 t integrating we get, velocity= V= 0.2 t2...

Q: The centroid distance y and the second moment of area INA of the channel section are 40 mm and 6 x 1...

Q: sentropically from intet to exhaust having an enthalpy drop=1200 kJ/kg. Assuming ideal conditions de...

Q: A solar panel is mounted on the roof of a house. Fig. 4.1 shows a section through part o solar panel...

A: A framework on which the photovoltic cells are mountedand which is used to convert the solar energy ...

Q: In a ballistic test shown in Figure Q2, a bullet is shot with a velocity of 450 m/s where it pierced...

A: Given Data The velocity of the bullet is: vb=450 m/s The velocity of block A is: vA=1.5 m/s The vel...

Q: Find the coordinate direction angles ( α 1 , β 1 , γ 1 ) of the force F1 so that the resultant force...

Q: PROBLEM 2. A circular shaft AB consists of a 250 mm long, 22 mm diameter steel 125 mm cylinder which...

Q: 750 kg of dry saturated steam at a pressure of 160 N/cm2 is generated in a boiler per hour. The temp...

A: Given mass of the steam ms=750kgpressure in boiler P=160N/cm2=16barheat loss at the exit of boiler Q...

Q: SIMPLE STRESSES 340 mm 1. Two plates are connected by bolts as shown in the figure. Compute the bear...

A: Given data: F=200 kNd=20 mmt=50 mmn=4×5=20 Need to determine the bearing stress in each bolt.

Q: A steel wheel of 900mm diameter on a horizontal steel rail. It carries a load of 50ON. The coefficie...

A: GIVEN DATA - W=500N D=900mm SO R=450mm μ=0.1 WE HAVE TO FIND VALUE OF FORCE

Q: 1.36 The bell crank, which is in equilibrium under the forces shown in the figure, is supported by a...

A: To find diameter of rod AB and stress in pin at D

Q: An automobile whose weight is 150 N and it is mounted on 4 identical springs due to its weight it sa...

A: given; automobile weight (w)=150Nmass (m)=wg =1509.81 =15.29kgdamp...

Q: Research on the four (4) types of advanced engineering materials. You may refer to our referenc book...

A: The multidisciplinary discipline of materials science, often known as materials science and engi...

Q: force necessary to roll the wheel

A: Given; A steel wheel of ; D=800 mm= 0.8m Load=600N Rolling resistance=0.2

Q: PROBLEM 2 : An ammonia simple saturation cycle operates evaporator and condenser temperatures of -20...

A: Given Evaporator temperature = -20 C Condenser temperature = 35 C Mass = 6000 kg Ice temperature = -...

Q: Moment diagrams. 14. (a) A timber beam of rectangular section is to support a load of 20KN/M uniform...

A: As we only solve upto one question, we will solve the first one. Please resubmit the other question ...

Q: Beam cross section is shown in Figure Q3 and given the second moment of area is I= 20.85 x 106 mm*. ...

A: Find the shear stress at point M, N, O, P and draw stress distribution over the cross section

Q: A mould has downsprue whose length is 30cm and the cross sectional area at the base of the downsprue...

A: Given data, Area of gate A= 2 cm² Length H= 30 cm Volume of mold cavity V= 1500 cm³

Q: (2013) A rubber cord of a Y– shaped object has a cross sectional area of 4 x 10-6 m² ? And relaxatio...

A: Draw the diagram of the rubber attached in Y-shaped object. Calculate the angle, θ. sinθ=35200θ=10....

Q: In this experiment, (S) is compressed to a spring (R) by a distance x-5cm, and then released for to-...

A: We will answer the first question (up to 3 subparts) since the exact one was not specified. Please r...

Q: (a) Describe/Illustrate in detail: Ways how to convert/transform the rotary motion (vertical or hori...

A: (a) In this problem, it is asking about the way to convert rotary motion of the shaft of a motor to ...

Q: For my medical device, I wish to create a material that is soft and will retain a lot of water. But ...

A: Clinical plastic items have become further developed as the worldwide market for top notch clinical ...

Q: Determine displacement

A: Given data : Force=F Work done=W To find : Displacement

Question

Calculate the maximum contact exposure rate at
the side surface of a 10-foot wide railcar loaded
with steel scrap with a 2 curie Cs-137 source at the
geometric center of the car. The TVL for scrap
metal (typical density of 65 lbs/cubic foot) is 16
inches.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

1.26 Repeat Problem 1.25 but assume that the surface of the storage vessel has an absorbance (equal to the emittance) of 0.1. Then determine the rate of evaporation of the liquid oxygen in kilograms per second and pounds per hour, assuming that convection can be neglected. The heat of vaporization of oxygen at –183°C is .
Consider a flat plate or a plane wall with a thickness L and a long cylinder of radius r0. Both of these are made of materials such that they can be treated as lumped capacitances (Bi0.1). Show that in each case, the characteristic length lc, defined lc=(V/As), can be approximated as (L/2) and (ro/2), respectively.
1.28 The sun has a radius of and approximates a blackbody with a surface temperature of about 5800 K. Calculate the total rate of radiation from the sun and the emitted radiation flux per square meter of surface area.
give sample problem with solution regarding interchange of radiations between two parelle vertical planes (heat transfer)
A small 100 cd spring is located in the center of a spherical mirror with a diameter of 10 cm and a focal length of 50 cm. Assuming that the total reflectance is about 80%, obtain the average brightness of the parallel beam reflected from the mirror.
A right circular cylinder has a height of 1 m and diameter of 75 cm. Find the view factor for the cylindrical to the base.
a) Define Stefan-Boltzmann Law and emissivity. b) Is there any surface whose emissivity value is greater than 1? If no, explain the reason.
Calculate the (τα) product for a two-glass-cover collector (KL = 0.0370 per plate) with a flat black collector absorber for radiation incident on the collector at an angle of (a) 25° and (b) 60°. εp = 0.96.
At the surface of the sun, the temperature is approximately 5800 K. How much energy is contained in the electromagnetic radiation filling a cubic meter of space at the sun's surface?
Q#01:a) Define Radiation and give at least 3 examples.b) Define Stefan-Boltzmann Law and emissivity. Is there any surface whose emissivity valueis greater than 1? If no, explain the reason.
A plate-type solar energy collectorr with an absorbing surface covered by a glass is to receive an incident radiation of 800 W/m2. The glass plate has a reflectivity of 0.12 and a transmissivity of 0.80. The absorbing surface has an absorptivity of 0.90. The area of the collector is 5 m2. How much solar energy in watts is absorbed by the collector? ANSWER: 3060 WATTS
Two circular plates of radii r1= 4 cm and r2 = 2 cm are (9) cm apart. Find view factorF21.