Calculate the number of series turns per pole required generator to enable it to maintain the voltage constant at 460 V be- tween no load and full load of 100 kW. Without any series winding, it is found that the shunt current has to be 2 A on no load and 2-65 A on full load to maintain the voltage constant at 460 V. Number of turns per pole on the shunt winding 2000_ If the series coils were wound with 8 turns per pole and had a total resistance of 0-01 2, what value of diverter resistance would be re- quired to give level compounding?

Calculate the number of series turns per pole required generator to enable it to maintain the voltage constant at 460 V be- tween no load and full load of 100 kW. Without any series winding, it is found that the shunt current has to be 2 A on no load and 2-65 A on full load to maintain the voltage constant at 460 V. Number of turns per pole on the shunt winding 2000_ If the series coils were wound with 8 turns per pole and had a total resistance of 0-01 2, what value of diverter resistance would be re- quired to give level compounding?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.4P

See similar textbooks

Similar questions

A separately excited generator has no-load voltage of 125V. A certain load rated at 1200W, 120V is then connected at the terminal. Calculate the series resistance needed to connect to the armature circuit in order for the load to operate at rated condition if the armature resistance is 0.0692Ω.
A 110V shunt generator has a full load current of 100A, shunt field resistance of 55 ohms and constant losses of 500W. If full load efficiency is 88%, find the armature resistance. Assuming voltage to be constant at 110V, calculate the efficiency at half load. Find the load current.
A Y- connected, 10-KVA, 230- has a field winding resistance of 4.59. At an operation of 0.85 lagging power factor, the excitation current is recorded at 10A. the core loss is 300W, and the mechanical loss is 200W. If the corresponding efficiency is 84.9%. calculate the per- phase armature winding resistance.
A short shunt compound DC generator delivers a load current of 30 A at 220 V and has armature, series field and shunt field resistances of 0.05, 0.3 and 200Ω respectively. Calculate the induced emf, the armature current and the voltage regulation. Allow 1 V per brush for contact dro
A DC shunt generator has a full load output of 10kW at a terminal voltage of 240V. The armature and the shunt field winding resistances are 0.6 and 160 ohms respectively. The sum of the mechanical and core-losses is 500W. calculate the power required in kW at the driving shaft at full-load, and the corresponding efficiency and voltage regulation
Calculate the full load voltage drop due to armature reaction In an experiment load test DC Shunt generator. Obtain the internal curve using the curves above.
A shunt generator has a field resistance of 60 ohms. When the generator driven 6KW, the terminal vtage is 125 Volts, while the generated emf is 133V. Determine a.) The armature resistance, and b.) The generated emf when the output is 2KW at terminal voltage of 135 V.
Two similar 6,600-V, three phase generators are running in parallel on constant-voltage andfrequency bus bars. Each has an equivalent resistance and reactance of 0.05 Ω and0.5 Ω respectively and supplies one half of a total load of 10,000 kW at a laggingp.f. of 0.8, the two machines being similarly excited. If the excitation of onemachine be adjusted until the armature current is 438 A and the steam supply to theturbine remains unchanged, find the armature current, the e.m.f. and the p.f. of theother alternator.
A shunt generator supplies a 31kW load at 230V through cables of resistance, R = 122mΩ. If the field winding resistance, Rf =50Ω and the armature resistance, Ra =51mΩ. Determine the following below: The terminal voltage is, Answer and unit for part 1 The e.m.f. generated in the armature is,
. A Short Shunt Compound DC Generator supplies 100-amp at 110-volt. Series field resistance of 0.04-ohm, armature resistance is 0.05-ohm, shunt field resistance of 57- ohm. Iron and friction losses mount to 852-watts. Find the power input and the over all efficiency.
A 110-V shunt generator has a full-load current of 100 A, shunt fieldresistance of 55 Ω and constant losses of 500 W. If F.L. efficiency is88%, find armature resistance. Assuming voltage to be constant at 110 V,calculate the efficiency at half F.L. And at 50% overload. Find the loadcurrent. Write the answer neatly.
1) total Armature Winding resistance of 60kW, 270V short shunt compound generator 54mΩ, series area windingits resistance is 40mΩ and the shunt field winding resistance is 135Ω. Brush-contact voltage drop is neglected.The generator supplies the load at Rated Power Rating (60kW) at rated voltage of 270V. Generatorthe voltage induced in the armature is 291V. (a) draw the equivalent circuit of the corresponding DC machine, specifying all current, voltage and winding resistors.Make appropriate current direction arrangements for the generator. (b) load current value (c) armature current value at full load