Calculate the pressure drop through horizontal sanitary stainless steel tubing (9 mm inner radius and 1.2 m long) for an apple juice drink that flows with a velocity of 3.13 ms - 1 . The density and viscosity of apple juice drink are 1100 kg m -3 and 0.8 x 10 -3 kg m -1 s -1 , respectively. Use the Moody diagram to solve this problem

Calculate the pressure drop through horizontal sanitary stainless steel tubing (9 mm inner radius and 1.2 m long) for an apple juice drink that flows with a velocity of 3.13 ms - 1 . The density and viscosity of apple juice drink are 1100 kg m -3 and 0.8 x 10 -3 kg m -1 s -1 , respectively. Use the Moody diagram to solve this problem

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.6P: 5.6 A fluid flows at 5 over a wide, flat plate 15 cm long. For each from the following list,...

See similar textbooks

Similar questions

A pipeline 0.5 m diameter and 1200 m long is used for transporting an oil of density 150 kg/m3 and of viscosity 0.91 Pa-s at 0.4 m2/s. If the roughness of the pipe is 0.5 mm, what is the pressure drop?
A certain garden hose is advertised to be able to deliver 550 gallons of water per hour. If the hose if 50 feet long and has an inside diameter of 5/8 inch, estimate the water pressure necessary to deliver this much water, assuming laminar flow and viscosity at 1.002 x 10-3 kg/(m-s)
Calculate the pressure drop of starfruit juice drink that flows with a velocity of 1.5 m/sthrough 1.2 m of horizontal sanitary stainless steel tubing with 9 mm inner diameter. Thedensity and viscosity of starfruit juice drink are 2300 kg m -3 and 0.8 x 10 -3 kg m -1 s -1 ,respectively. Calculate the energy losses due to the friction. Use the Moody diagram tosolve this problem.
An oil gusher shoots crude oil 23.0 m into the air through a pipe with a 0.100 m diameter. Neglecting air resistance but not the resistance of the pipe, and assuming laminar flow, calculate the pressure (in N/m2) at the entrance of the 45.0 m long vertical pipe. Take the density of the oil to be 900 kg/m3 and its viscosity to be 1.00 (N/m2) · s (or 1.00 Pa · s). Note that you must take into account the pressure due to the 45.0 m column of oil in the pipe.
A shaft 70-mm in diameter is being pushed at a speed of 400mm/s through a bearing sleeve 70.2-mm in diameter and 250mm long. The clearance is filled with oil with a kinematic viscosity of v = 0.005 ?2/? and SG=0.9. Find the frictional resistance exerted by the oil on the shaft in Newtons (N).
steel tape 0.5 mm thick and 20 mm wide is pulled by a force F through a slit opening 1.5 mm and length 15 mm. Considering that the tape is centered on the slit, that lubricating oil of viscosity µ = 0.4 Nm-2s? fills the gap spaces not occupied by the tape and that the maximum tape speed is 10 m/s, calculate the maximum force F. Expected Answer: Maximum Force = 4.8N
An ideal gas at 250 °C and atmospheric pressure flows through a smooth pipe with ID 6-in. The molecular weight of the ideal gas is 35 g/mol, and its viscosity is 0.002 cP. If the average velocity of the gas is 3.5 m/s, determine the pressure drop per unit length (m).
PROB 3 A capillary tube is being used to measure the viscosity of a Newtonianliquid. The has a 20-mm radius and a length of 20-cm. Estimate theviscosity coefficient for the liquid if the pressure of 2500 Pa is required tomaintain a flow rate of 1 kg/s with ρ = 998 kg/m3
3.1 A cylindrical plug, 120mm long with a diameter of 95 mm, slides concentrically in a fixed cylinderwith an internal diameter of 95,2 mm. The radial clearance is filled with oil with a viscosity of 0.2 Pa.sCalculate the Force required to slide the plug along the cylinder at a speed of 5 m/s against the viscousresistance of the oil, the power lost due to the viscous resistance and the Kinematic viscosity of the oil ifits density is 850 kg/m 3 . A pressure intensifier is used in reverse deboost the pressure in a hydraulic system from 15MPa to7MPa. The volume of fluid required in the low pressure side is 700ml and the length of the stroke of thepiston is to be half the diameter of the low pressure piston. Calculate the diameters of the high-pressureand low pressure sides as well as the stroke length of the piston.
Find the head lost due to friction in a pipe of radius 20 cm and length 50m, through which oil is flowing at a velocity of 5 m/s using (a) Darcy formula (b) Chezy formula for which C= 65, Take Specific gravity of the oil is 0.8 and Dynamic viscosity is 8 X 10-3 poise.
Sulfuric acid with a density of 1980 kg / m3 and a viscosity of 26.7 cP flows in a pipe with a diameter of 35 mm. If the acid flow rate is 2 m3 / min, what is the pressure loss due to friction in a 30 m long smooth pipe? a. Reynold number = Answer. b. Loss of Pressure = AnswerkPa.
PROB E. A capillary –tube viscometer is being selected to measure viscosity of a liquid food. The maximum viscosity to be measured will be 230 cP and the maximum mass rate is 900 grams per hour. If the tube length is 10 cm and the maximum sustainable pressure is 25 Pa, determine the nominal diameter size of the tube to be used.