Calculate the pressure drop of starfruit juice drink that flows with a velocity of 1.5 m/s through 1.2 m of horizontal sanitary stainless steel tubing with 9 mm inner diameter. The density and viscosity of starfruit juice drink are 2300 kg m -3 and 0.8 x 10 -3 kg m -1 s -1 , respectively. Calculate the energy losses due to the friction. Use the Moody diagram to solve this problem.

Calculate the pressure drop of starfruit juice drink that flows with a velocity of 1.5 m/s through 1.2 m of horizontal sanitary stainless steel tubing with 9 mm inner diameter. The density and viscosity of starfruit juice drink are 2300 kg m -3 and 0.8 x 10 -3 kg m -1 s -1 , respectively. Calculate the energy losses due to the friction. Use the Moody diagram to solve this problem.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.6P: 5.6 A fluid flows at 5 over a wide, flat plate 15 cm long. For each from the following list,...

See similar textbooks

Similar questions

Calculate the pressure drop through horizontal sanitary stainless steel tubing (9 mminner radius and 1.2 m long) for an apple juice drink that flows with a velocity of 3.13 ms -1 . The density and viscosity of apple juice drink are 1100 kg m -3 and 0.8 x 10 -3 kg m -1 s -1 , respectively. Use the Moody diagram to solve this problem.
Water flowing in a straight cylinder tube with radius of 3mm, has a maximum velocity U0=15cm/s. If the density and viscosity of the water are 1000kg/m3 and 1.0 x 10 -3 (Pa.s), and the flow is fully developed with a profile of u=U0(1-(r/a)2), calculate the Reynold’s number of the flow; calculate the mass flow rate in units of kg/s in the tube If the tube has a length of 50cm, calculate the flow resistance force of the tube wall imposed to the flow.
A Pitot-static probe is mounted in a 2.5-cm-inner diameter pipe at a location where the local velocity is approximately equal to the average velocity. The oil in the pipe has density ? = 860 kg/m3 and viscosity ? = 0.0103 kg/m⋅s. The pressure difference is measured to be 95.8 Pa. Calculate the Reynolds number of the ﬂow of Prob. Is it laminar or turbulent?
Pure milk at 293 K has a density of 1030 kg / m3 and a viscosity of 2.12 cp flowing at a rate of 2,605 kg / s in a pipe having a diameter of 100 mm. a. Calculate the Reynolds number. = Answer . b. Is the flow turbulent No, yes . c. The flow rate required for Reynold's number 2100 is = Answer m / s.
A shaft 70.0 mm in diameter is being pushed at a speed of 400 mm/s through a bearing sleeve 70.2 mm in diameter and 250 mm long. The clearance, assumed uniform, is filled with oil at 20 deg C with kinematic viscosity of 0.005 m^2/s and specific gravity 0.9. If the shaft is fixed axially and rotated inside the sleeve at 2000 rpm, determine the power required to rotate the shaft.
A shaft 70-mm in diameter is being pushed at a speed of 400mm/s through a bearing sleeve 70.2-mm in diameter and 250mm long. The clearance is filled with oil with a kinematic viscosity of v = 0.005 m²/s and SG-0.9. A. Find the frictional resistance exerted by the oil on the shaft in Newtons (N). B. If the shaft in the problem above is fixed axially and rotated inside the sleeve at 2000 rpm, determine the resisting torque exerted by the oil and the power required to rotate the shaft in kilowatts (kW).
Conduct thorough a research on Reynolds Number, laminar and turbulent flow as it relates to mechanics of fluids
steel tape 0.5 mm thick and 20 mm wide is pulled by a force F through a slit opening 1.5 mm and length 15 mm. Considering that the tape is centered on the slit, that lubricating oil of viscosity µ = 0.4 Nm-2s? fills the gap spaces not occupied by the tape and that the maximum tape speed is 10 m/s, calculate the maximum force F. Expected Answer: Maximum Force = 4.8N
An oil gusher shoots crude oil 23.0 m into the air through a pipe with a 0.100 m diameter. Neglecting air resistance but not the resistance of the pipe, and assuming laminar flow, calculate the pressure (in N/m2) at the entrance of the 45.0 m long vertical pipe. Take the density of the oil to be 900 kg/m3 and its viscosity to be 1.00 (N/m2) · s (or 1.00 Pa · s). Note that you must take into account the pressure due to the 45.0 m column of oil in the pipe.
A shaft 70-mm in diameter is being pushed at a speed of 400mm/s through a bearing sleeve 70.2-mm in diameter and 250mm long. The clearance is filled with oil with a kinematic viscosity of v = 0.005 ?2/? and SG=0.9. Find the frictional resistance exerted by the oil on the shaft in Newtons (N). And when the shaft is fixed axially and rotated inside the sleeve at 2000 rpm, determine the resisting torque exerted by the oil and the power required to rotate the shaft in kiloWatts (kW).
Ethylene Glycol at 60°C with a velocity of 4 cm/s enters a 2.5 cm diameter tube. The viscosity at the given temperature is 4.75 x 10−6 ?2/s. Determine the Reynolds number and its type of fluid flow. Show your step by step solution.
Laminar flow occurs when the Reynolds number (Re*) is below 2000; turbulent flow occurs when the Reynolds number is above 2000. For the following species, determine the maximum value of the average 1D speed for which laminar flow will occur: a) Ne at 293 K where ?η is 313 ?μP and ?ρ = (PM)/(RT) through a 2.00 mm (id) pipe b) Liquid water at 293 K where ?η is 0.891 cP and ?ρ = 0.998 g/mL through a 2.00 mm (id) pipe *Re = (?ρ **d)/?η, where d is the diameter of the tube through which the fluid is flowing.