A horizontal thin plate with a length of L= 10 cm is tiled with a constant heat flux from the bottom and is cooled by air at the top. The air velocity is U = 40 m / s and the temperature is 20 ° C. What should be the minimum heat flux so that the plate temperature does not exceed 80°C? (kW / m²) v 17.94 x 10-6 m²/s = 0.0277 W/(m.K) Pr = 0.71

A horizontal thin plate with a length of L= 10 cm is tiled with a constant heat flux from the bottom and is cooled by air at the top. The air velocity is U = 40 m / s and the temperature is 20 ° C. What should be the minimum heat flux so that the plate temperature does not exceed 80°C? (kW / m²) v 17.94 x 10-6 m²/s = 0.0277 W/(m.K) Pr = 0.71

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.36P

See similar textbooks

Similar questions

An electrical transmission line of 1.2-cm diameter carries a current of 200 amps and has a resistance of 310-4 ohm per meter of length. If the air around this line is at v, determine the surface temperature on a windy day, assuming a wind blows across the line at 33 km/h.
Determine the rate of heat loss from the wall of a building resulting from a 16 km/h wind blowing parallel to its surface. The wall is 24 m long and 6 m high, its surface temperature is 27C, and the temperature of the ambient air is 4C.
5.7 The average Reynolds number for air passing in turbulent flow over a 2-m-long, flat plate is . Under these conditions, the average Nusselt number was found to be equal to 4150. Determine the average heat transfer coefficient for an oil having thermal properties similar to those in Appendix 2, Table 18, at at the same Reynolds number and flowing over the same plate.
During a cold winter day, wind at 55 km/h is blowing parallel to a 4m high and 10m long wall of a house. If the air outside is at 5 degrees Celsius and the surface temperature of the wall is 12 degrees Celsius , determine the rate of heat loss from the wall by convection. What would your answer be if the wind velocity has doubled? From Table A-1:thermal conductivity, k = 0.0246 W/m degrees Celsiusviscosity, v = 1.4 x 10^-5 m^2/sPrandtl no. Pr = 0.717
Water at a temperature of 25oC flows parallel over a flat plate with free-stream velocity of 2 m/s. The plate surface temperature is uniform at 86oC. Calculate: a) Thermal boundary layer thickness at x = 8 cm from leading edge; b) Local heat flux on x = 8 cm from leading edge; c) Total heat transfer rate in the area of plate L = 8 cm from the leading edge and width w = 10 cm.
Prove that the thermocouple will underestimate the temperature of airflow by more than 15% but less than 30% in a large air duct if the temperature of the hot air is 1367 K, duct-wall temperature is 533 K, emissivity of the thermocouple is 0.5, and the convection heat-transfer coefficient is 114 W/m2 -K.
Air at 20oC and 1 atm flows over a flat plate at 35 m/s. The plate is 75 cm long and 100 cm depth and is maintained at 60oC. Calculate (a) velocity boundary layer thickness at the leading edge, (b) thermal boundary layer thickness at the distance of 10 cm from the leading edge, and (c) thermal boundary layer thickness at the trailing edge.
A 5.0-cm-diameter cylinder is heated to a temperature of 200°C, and air at 30 °C forced across it at a velocity of 50 m/s (h = 180 W/m2 K). If the surface emissivity is 0.7, calculate the total heat loss per unit length if the walls of the enclosing room are at 10 °C. Comment on your calculation.
Air at a temperature of 25oC flows parallel over a flat plate with free-stream velocity of 2 m/s. The plate surface temperature is uniform at 86oC. Calculate: a) Thermal boundary layer thickness at x = 8 cm from leading edge; b) Local heat flux on x = 8 cm from leading edge; c) Total heat transfer rate in the area of plate L = 8 cm from the leading edge and width w = 10 cm.
Air is flowing in parallel over the upper surface of a flat plate with a length of 4 m. The first half of the plate length, from the leading edge, has a constant surface temperature of 50°C. The second half of the plate length is subjected to a uniform heat flux of 86 W/m2. The air has a free stream velocity and temperature of 0.5 m/s and 10°C respectively. The properties of air at Tf = 30°C are k = 0.02588 W/m∙K, ν = 1.608 × 10−5 m2/s, and Pr = 0.7282. Determine the local convection heat transfer coefficients at 1 m and 3 m from the leading edge.
Air is flowing in parallel over the upper surface of a flat plate with a length of 4 m. The first half of the plate length, from the leading edge, has a constant surface temperature of 50°C. The second half of the plate length is subjected to a uniform heat flux of 86 W/m2. The air has a free stream velocity and temperature of 0.5 m/s and 10°C respectively. The properties of air at Tf = 30°C are k = 0.02588 W/m∙K, ν = 1.608 × 10−5 m2/s, and Pr = 0.7282.Determine the local convection heat transfer coefficients at 1 m from the leading edge.
Q3: Air flows across a 20-cm-square plate with a velocity of $ m/s. Free-stream conditions are 10-C and 0.2 atm. A heater in the plate surface furnishes a constant heat-flux condition at the wall so that the average wall temperature is 100-C. Calculate the surface heat flux and the value of h at an x position of 10 cm. Answers: Q= 1414 W, b= 13.3 Wm?.C