Calculate the rate of overall heat transfer coefficient for the tube heat exchanger with inner and outer heat transfer coefficient of 670 W/m2 -K and 1880 W/m2 -K, respectively. Thermal conductivity of the tube wall is 27 W/m-K. The diameter and the thickness of the tube are 4 cm and 1.5 mm, respectively.

Calculate the rate of overall heat transfer coefficient for the tube heat exchanger with inner and outer heat transfer coefficient of 670 W/m2 -K and 1880 W/m2 -K, respectively. Thermal conductivity of the tube wall is 27 W/m-K. The diameter and the thickness of the tube are 4 cm and 1.5 mm, respectively.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter10: Heat Exchangers

Section: Chapter Questions

Problem 10.32P

See similar textbooks

Similar questions

Water flowing in a long, aluminum lube is to be heated by air flowing perpendicular to the exterior of the tube. The ID of the tube is 1.85 cm, and its OD is 2.3 cm. The mass flow rate of the water through the tube is 0.65kg/s, and the temperature of the water in the lube averages 30C. The free-stream velocity and ambient temperature of the air are 10m/sand120C, respectively. Estimate the overall heat transfer coefficient for the heat exchanger using appropriate correlations from previous chapters. State all your assumptions.
10.1 In a heat exchanger, as shown in the accompanying figure, air flows over brass tubes of 1.8-cm 1D and 2.1-cm OD containing steam. The convection heat transfer coefficients on the air and steam sides of the tubes are , respectively. Calculate the overall heal transfer coefficient for the heal exchanger (a) based on the inner tube area and (b) based on the outer tube area.
In a double pipe heat exchanger if the wall resistance can be neglected and the convective heat transfer coefficient on inner diameter basis of inner pipe is 1W/m2K and convective heat transfer coefficient on basis of outside diameter is 600W/m2K, then overall heat transfer coefficient is
Under what conditions can a counter-flow heat exchanger have an effectiveness of one? What would your answer be for a parallel-flow heat exchanger?
Q 3.1: What effect do finned surfaces have on the overall heat transfer coefficient and hence the performance of a heat exchanger? When is the use of fins most appropriate?
What are the common causes of fouling in a heat exchanger? How does fouling affect heat transfer and pressure drop?
What is the heat capacity rate? What can you say about the temperature changes of the hot and cold fluids in a heat exchanger if both fluids have the same capacity rate? What does a heat capacity of infinity for a fluid in a heat exchanger mean?
What are the common approximations made in the analysis of heat exchangers?
Why does a “mixed” or “unmixed” fluid arrangement influence heat-exchanger performance?
A thin-walled double-pipe counter-flow heat exchanger is to be used to cool oil (cp = 2200 J/kg·K) from 150°C to 40°C at a rate of 2 kg/s by water (cp = 4180 J/kg·K) that enters at 22°C at a rate of 1.5 kg/s. The diameter of the tube is 2.5 cm, and its length is 6 m. Determine the overall heat transfer coefficient of this heat exchanger.
A counterflow double-tube heat exchanger with hot engine oil fluid at inlet and outlet temperatures of 190°C and 60°C, respectively, and a flow rate of 0.65 kg/s. While cold engine oil at a flow rate of 1.05 kg/s has an exit temperature of 149°C and Cp-1.84 kJ/kg.K. It is known that the overall heat transfer coefficient is 305 W/m².K. Determine the heat transfer surface area of the heat exchanger.
What is the role of the baffles in a shell-and-tube heat exchanger? How does the presence of baffles affect the heat transfer and the pumping power requirements? Explain.