The turbine develops 230 kW of power, which is transmitted to the gears such that both B and C receive an equal amount. The rotation of the 100-mm-diameter A992 steel shaft is w = 720 rev/min. (Figure 1) The journal bearing at D allows the shaft to turn freely about its axis. Determine the absolute maximum shear stress in the shaft. Express your answer to three significant figures and include appropriate i µA ? 'max Value Units

The turbine develops 230 kW of power, which is transmitted to the gears such that both B and C receive an equal amount. The rotation of the 100-mm-diameter A992 steel shaft is w = 720 rev/min. (Figure 1) The journal bearing at D allows the shaft to turn freely about its axis. Determine the absolute maximum shear stress in the shaft. Express your answer to three significant figures and include appropriate i µA ? 'max Value Units

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The propellers of a ship are connected to an A-36 steel shaft that is 60 m long and has an outer diameter of 340 mm and inner diameter of 260 mm. If the power output is 4.5 MW when the shaft rotates at 20 rad/s, determine themaximum torsional stress in the shaft and its angle of twist.
Determine the diameter of a solid steel shaft that will transfer 30 MW at 1500 RPM with a 1 degree twist angle for every 20 diameters of length. G=80GN/m2. Give me the solution of this please. Ans. D = 3.03 m
A generator driven by a wind turbine is required to deliver 5 MW of power at the generator terminals. The turbine is a two-blade propeller rotating about a horizontal axis and the maximum permitted shear stress of the turbine shaft is 55x106 N/m2 The rotor is designed to operate at a rotational speed of 45 revolution per seconds .The stage efficiencies are Cp 0.32, ngb = 0.90, ng = 0.92. %3D . (i) If the turbine delivers its rated power at a wind average speed of 22 m/s, calculate the corresponding diameter of the propeller and its TSR, assuming a typical value for the overall efficiency. The air density may be assumed to have a value 1.29 kg/m³. (ii) Calculate the torque on the turbine shaft.
The motor A delivers 3000 hp to the shaft at 1500 rev/min, of which 1000 hp is removed by gear B and 2000 hp is removed by gear C. 1.) Determine the maximum shear stress in the shaft in ksi. (Answer in 2 decimal places) 2.) Determine the angle of twist in degrees of end D relative to end A. Use G = 12 x 106 psi for steel, and assume that friction at bearing D is negligible. (Answer in 3 decimal places)
The solid steel shaft is supported by frictionless bearings in D and E. This system is connected to a motor that provides 5 kW of power to the shaft while rotating at w = 75 rpm. If A and B gears get 2 kW and 3 kW respectively, determine the minimum shaft diameter. w rotation speed and safety shear stress τem = 35MPa are known and given in the table with your names below.
A hollow steel shaft of length 1.75 m transmits 2000 kW of power at a speed of150 rev/min. The inside diameter is to be 0.75 times the outside diameter. Themaximum allowable torsional shear stress for the steel is 130 MN/m2and themodulus of rigidity (G) for the steel is 83 GN/m2. Given that a factor of safety of2 is required for the shaft, determine:i) the torque acting on the shaft;ii) the required external and internal diameters for the shaft; iii) the torsional shear stress set-up in the shaft material at the inside surfaceof the hollow shaft, and sketch the stress distribution through the shaftwall;iv) the angle of twist (in degrees) due to the torque.
A hollow shaft for a rotary compressor is to be designed to transmit a maximum torque of 4750 N-m.The shear stress in the shaft is limited to 50 MPa. Determine the inside and outside diameters of theshaft, if the ratio of the inside to the outside diameter is 0.4. [Ans. 35 mm ; 90 mm]
Q: Part A: Determine the absolute maximum shear stress in the shaft. Part B: Determine the angle of twist of end EE of the shaft relative to BB. Given: The turbine develops 150 kW of power, which is transmitted to the gears such that CC receives 70% and DD receives 30%. The rotation of the 100-mm diameter A-36 steel shaft is ωomega = 600 rev/min . The journal bearing at EE allows the shaft to turn freely about its axis. The shear modulus of elasticity for A-36 steel is 75 GPa.
A solid shaft 100 mm diameter transmits 100.6 horsepower with a maximum allowable shear stress 25 MN/m ^2 . What is the spced of rotation of the shaft in (r.p.m)? (b) If the solid shaft is replaced by the hollow shafl transmitting 100 kW at the same rotation speed of the solid shaft. The hollow shaft has a mean torque =5/6 of maximum torque with the angle of twist 0.35° per meter length of the shafl and G= 80 GN/m^2 Determine the dimensions ofr the hollow shaft if the internal diameter of the shaft is to be 80 % of the external diameter.
PLSSS ANSWER WITHIN AN HOUR At what angular velocity will the stress of the rotating steel ring equal 250 MPa if its mean radius is 220 mm? The density of steel 7.85 Mg/m3 .
a) A solid alloy shaft 5cm diameter is to be coupled in series with a hollow steel shaft ofthe same external diameter. Find the internal diameter of the steel shaft if the angle oftwist per unit length is to be 75% of that of the alloy shaft. Determine the speed at whichthe shafts are to be driven to transmit 200kW, if the limits of shearing stress are to be55N/mm2 and 75N/mm2 in alloy and steel respectively. Gsteel = 2.2Galloy
The 25 mm diameter shaft is made of a material having an allowable shear stress of 80 MPa. If the power generated is 15 kW, determine the minimum allowable angular velocity of the shaft (rad/s) indicatwe free body diagram